Ford AA5Z-6714-A Filter Assembly - Oil

You can Select Your Vehicle to check if AA5Z-6714-A fits your vehicle.

Position a drain pan under the oil drain plug and remove the plug with the correct-sized wrench, wearing a rubber glove to avoid burns. Shift the pan as oil flow slows, inspect the old oil for metal particles, clean the drain plug and surrounding area, reinstall the plug, and move the drain pan under the oil filter.

During an oil change, the oil filter should be loosened with a filter wrench, unscrewed by hand while tilting the open end upward to prevent spills, and the mounting surface on the engine block should be cleaned while ensuring no old gasket remnants remain.

Remove tools and materials, lower the vehicle, and add fresh oil through the filler cap using a funnel to prevent spills. Pour four quarts of oil, wait for drainage, and check the level with the dipstick.

Proper disposal of the old oil is crucial, and it should not be poured on the ground or down a drain. Instead, it should be taken to a recycling facility.

Frequent oil changes are crucial for preventive maintenance because aging engine oil becomes diluted and contaminated over time, leading to premature engine wear. Regular oil changes help maintain engine health and prolong its lifespan.

Care should be taken not to touch the hot exhaust components, and one should note their routing to avoid contact.

Loosen and remove the oil filter with a wrench or by hand, tilting it upward to prevent oil spillage. Clean the mounting surface and gasket, compare the old filter to the new one, lubricate the gasket with engine oil, and install the new filter by hand.

Regular oil changes are crucial preventive maintenance tasks for home mechanics because aging engine oil becomes diluted and contaminated over time, resulting in premature engine wear. Prior to commencing the procedure, ensure that you have all the necessary tools and an ample supply of rags or newspapers to address potential oil spills. Access to the oil drain plug and filter can be facilitated by elevating the vehicle on a hoist, driving it onto ramps, or supporting it with jackstands. If you're unfamiliar with changing the oil on this vehicle, locate the oil drain plug and oil filter beneath it while being cautious of the warm exhaust components. Start the engine and let it reach normal operating temperature, as warm oil and sludge flow more easily. If new oil, a filter, or tools are required, use the vehicle to obtain them and simultaneously warm up the engine and oil. Park on level ground, turn off the engine, and remove the oil filler cap from the valve cover. Elevate the vehicle safely on jackstands, making sure it is securely supported. While avoiding contact with hot exhaust components, position a drain pan beneath the engine's plug and remove the plug using an appropriately sized wrench or socket. It is advisable to wear a rubber glove when loosening the plug to prevent scalding from hot oil. Adjust the position of the drain pan as oil flow slows down to a trickle and inspect the old oil for the presence of metal particles. After all the oil has drained, wipe the drain plug clean with a rag, as any small metal particles clinging to it can contaminate the new oil. Clean the area around the drain plug opening, reinstall the plug, and securely tighten it without stripping the threads. Position the drain pan under the oil filter, loosen the filter counterclockwise using an oil filter wrench, and then unscrew it by hand while immediately tilting the open end upward to prevent oil spillage. Use a clean rag to wipe the mounting surface on the block and ensure no remnants of the old gasket remain, which can be scraped off if necessary. Verify that the new filter matches the old one before applying engine oil to its rubber gasket and screwing it into place, being cautious not to overtighten it to avoid gasket damage. Most filter manufacturers recommend hand-tightening the filter only, typically 3/4-turn after the gasket contacts the block, while adhering to the instructions on the filter or container. Remove all tools and materials from beneath the vehicle, taking care not to spill oil from the drain pan, and then lower the vehicle. Add fresh oil through the oil filler cap using a funnel to prevent spills on the engine's top. Pour four quarts of oil into the engine, allow a few minutes for it to drain into the pan, and check the oil level with the dipstick. If the oil level falls within the "OK" range, reinstall the filler cap. Start the engine and let it run for about a minute, inspecting under the vehicle for leaks around the oil pan drain plug and oil filter. In case of any leaks, stop the engine and slightly tighten the plug or filter. After a few minutes, recheck the oil level with the dipstick and add oil as needed to reach the "OK" range. During the initial trips following the oil change, be vigilant about checking for leaks and maintaining the proper oil level. Disposing of the old oil is essential, and it should not be poured onto the ground or down a drain. Instead, check with local auto parts stores, disposal facilities, or environmental agencies to find out if they accept used oil for recycling. Once the oil has cooled, it can be drained into a container such as capped plastic jugs, bottles, or milk cartons for transport to an authorized disposal site.

Yes, the oil type does not matter with this filter