How to replace windshield wiper arm and Wiper Blade on Ford Bronco II?

Raise the blade end of the front wiper arm off of the windshield. Move the slide latch away from the pivot shaft. The wiper-arm can now be removed from the shaft without the use of any tools. Be sure the wipers are in the parked position, and the blade assembly is in its correct position. Push the main head over the pivot shaft. Hold the main arm head onto the pivot shaft while raising the blade end of the wiper arm and push the slide latch into the lock under the pivot shaft head. Lower the blade to the windshield. If the blade does not lower to the windshield, the slide latch is not completely in place. For the rear wiper, raise the windshield wiper blade/arm off of the glass and place it into the service position. Using a small, flat bladed prytool, release the retaining clip at the base of the windshield wiper pivot arm. Carefully pry the wiper arm from the shaft. Ensure that the wiper motor pivot shaft is in the park position. Position the wiper arm over the shaft and firmly push it on until it stops. Lower the wiper blade/arm against the glass. The blade is properly positioned when it firmly contacts the wind-shield wiper arm stop. If it does not, remove the arm again and reposition it so that it does.

Genuine Ford Bronco II Wiper Blade

Windshield Wiper Blade

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Wiper Blades found

View related parts
Ford Bronco II Wiper Blade Assembly
Part Number: 2U2Z-17528-EA
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Blade Assembly - Wiper
- Position: Passenger Side
- Replaced by: GU2Z-17V528-L
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Bronco II Wiper Blade Assembly
Part Number: XL6Z-17528-AA
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Blade Assembly - Wiper
- Replaced by: GU2Z-17V528-L
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Bronco II Wiper Blade Assembly
Part Number: 2U2Z-17528-AA
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Blade Assembly - Wiper
- Replaced by: GU2Z-17V528-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Bronco II Wiper Blade Assembly
Part Number: XL2Z-17528-AA
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Blade Assembly - Wiper
- Replaced by: GU2Z-17V528-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Bronco II Wiper Blade Assembly
Part Number: 4U2Z-17528-FA
$10.64 MSRP: $13.98
You Save: $3.34 (24%)
Product Specifications
- Other Name: Blade Assembly - Wiper
- Position: Passenger Side
- Replaced by: MU2Z-17V528-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Bronco II Wiper Blade Assembly
Part Number: 4U2Z-17528-AA
Product Specifications
- Other Name: Blade Assembly - Wiper; Blade Assembly, Wiper Blade
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT

Ford Bronco II Wiper Blade

This Ford Bronco II Wiper Blade is an important part that assists in ensuring that drivers get to have the premier visions while driving especially in times of rainy or snowy seasons. These blades are mounted to remove water, snow, dirt and other harms from the windshield so that the driver can have a good vision of the road in front. Comprising a metal that has a rubber edge, the wiper blade is driven by an electric or an air motor which enables it to oscillate in order to remove the glass. For personal use, Ford Bronco II vehicles could come with synchronized radial arms, while for the commercial use the place could have hard-wearing pantograph arms. Further, windscreen washer systems may be incorporated in some vehicle perhaps to spray water or antifreeze of some sort equally helping the wipers to clean the glass.

We provide a wide range of Ford Bronco II Wiper Blade at the best prices possible. If you need Ford Bronco II Wiper Blade, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Bronco II Wiper Blade Parts Questions & Experts Answers

Wiper Blade Assembly
2U2Z-17528-EA
Q: How to replace windshield wiper arm and Wiper Blade on Ford Bronco II?
A: Raise the blade end of the front wiper arm off of the windshield. Move the slide latch away from the pivot shaft. The wiper-arm can now be removed from the shaft without the use of any tools. Be sure the wipers are in the parked position, and the blade assembly is in its correct position. Push the main head over the pivot shaft. Hold the main arm head onto the pivot shaft while raising the blade end of the wiper arm and push the slide latch into the lock under the pivot shaft head. Lower the blade to the windshield. If the blade does not lower to the windshield, the slide latch is not completely in place. For the rear wiper, raise the windshield wiper blade/arm off of the glass and place it into the service position. Using a small, flat bladed prytool, release the retaining clip at the base of the windshield wiper pivot arm. Carefully pry the wiper arm from the shaft. Ensure that the wiper motor pivot shaft is in the park position. Position the wiper arm over the shaft and firmly push it on until it stops. Lower the wiper blade/arm against the glass. The blade is properly positioned when it firmly contacts the wind-shield wiper arm stop. If it does not, remove the arm again and reposition it so that it does.