How do you check and replace fuel injectors, Fuel Pressure Regulator,Fuel Rail,Intake Manifold,Throttle Body and Throttle Position Sensor on a Ford Crown Victoria 5.0L engine?

The first step in removing the air intake plenum and throttle body on a 5.0L engine involves disconnecting the negative battery cable. Also, unplug electrical connectors at the air bypass valve, throttle position sensor, and EGR position sensor. Disconnect the accelerator cable and transmission linkage from the throttle body assembly, remove the accelerator cable/TV cable bracket from the intake manifold, and label and detach vacuum lines from the upper intake manifold vacuum tree, EGR valve, and fuel pressure regulator. Make sure to disconnect the PCV system or any canister purge line if it is present and also downsize the water pipes of spacer coolant lines for EGR. Unbolt six (6) upper manifold retaining bolts to separate the upper manifold and throttle body as an assembly from the lower manifold. Ensure the gasket is in place during installation, attach new gasket(s) onto lower intake mounting face, and snug up air intake plenum with throttle body assembly by using six (6) upper manifold retaining bolts right up to the recommended torque value.

Genuine Ford Crown Victoria Fuel Injector

Gas Injector

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Fuel Injectors found

View related parts
Ford Crown Victoria Injector Assembly
Part Number: 6W7Z-9F593-AA
$52.03 MSRP: $86.00
You Save: $33.97 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Injector Assy; Injector
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Injector Assembly
Part Number: XL2Z-9F593-CA
$57.18 MSRP: $109.45
You Save: $52.27 (48%)
ADD TO CART
Product Specifications
- Other Name: Injector Assy; Injector
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT 4R75W
- 2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Injector Assembly
Part Number: 5W7Z-9F593-AA
$43.09 MSRP: $68.73
You Save: $25.64 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Injector Assy; Injector
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT
View related parts
Ford Crown Victoria Injector Assembly
Part Number: 1W7Z-9F593-AA
Product Specifications
- Other Name: Injector Assy; Injector
- Manufacturer Note: Injector asy. (Fuel) #1W7E 9F593-A5A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Injector Assembly
Part Number: XL3Z-9F593-CA
$0.00
Product Specifications
- Other Name: Injector Assy; Injector
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Injector Assembly
Part Number: F5TZ-9F593-B5A
Product Specifications
- Other Name: Injector Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2001 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Injector Assembly
Part Number: XW7Z-9F593-AB
Product Specifications
- Other Name: Injector Assy; Injector
- Manufacturer Note: Injector asy. (Fuel) #XW7E 9F593-A5B
- Replaces: F81Z-9F593-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W

Ford Crown Victoria Fuel Injector

The Ford Crown Victoria Fuel Injector is a component that injects fuel into the engine cylinder in the correct amount decided by the Engine Control Module on the right mixture of air and fuel. This system is "returnless," which minimises fuel pipes and avoid failure that cause engine stall and poor fuel economy. Some types of Crown Victoria entail the use of fuel injectors that include the direct and the indirect injection systems with the latter being in many cases electronically controlled in order to enhance efficiency. Fuel injectors are therefore central and very instrumental when it comes to improving the function of carburetors and overall performance of an engine and hence the car.

We provide a wide range of Ford Crown Victoria Fuel Injector at the best prices possible. If you need Ford Crown Victoria Fuel Injector, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Crown Victoria Fuel Injector Parts Questions & Experts Answers

Injector Assembly
1W7Z-9F593-AA
Q: How do you check and replace fuel injectors, Fuel Pressure Regulator,Fuel Rail,Intake Manifold,Throttle Body and Throttle Position Sensor on a Ford Crown Victoria 5.0L engine?
A: The first step in removing the air intake plenum and throttle body on a 5.0L engine involves disconnecting the negative battery cable. Also, unplug electrical connectors at the air bypass valve, throttle position sensor, and EGR position sensor. Disconnect the Accelerator Cable and transmission linkage from the throttle body assembly, remove the accelerator cable/TV cable bracket from the intake manifold, and label and detach vacuum lines from the upper intake manifold vacuum tree, EGR valve, and fuel pressure regulator. Make sure to disconnect the PCV system or any canister purge line if it is present and also downsize the water pipes of spacer coolant lines for EGR. Unbolt six (6) upper manifold retaining bolts to separate the upper manifold and throttle body as an assembly from the lower manifold. Ensure the gasket is in place during installation, attach new gasket(s) onto lower intake mounting face, and snug up air intake plenum with throttle body assembly by using six (6) upper manifold retaining bolts right up to the recommended torque value.