How do you check and replace fuel injectors, Fuel Pressure Regulator,Fuel Rail,Intake Manifold,Throttle Body and Throttle Position Sensor on a Ford Crown Victoria 5.0L engine?

The first step in removing the air intake plenum and throttle body on a 5.0L engine involves disconnecting the negative battery cable. Also, unplug electrical connectors at the air bypass valve, throttle position sensor, and EGR position sensor. Disconnect the accelerator cable and transmission linkage from the throttle body assembly, remove the accelerator cable/TV cable bracket from the intake manifold, and label and detach vacuum lines from the upper intake manifold vacuum tree, EGR valve, and fuel pressure regulator. Make sure to disconnect the PCV system or any canister purge line if it is present and also downsize the water pipes of spacer coolant lines for EGR. Unbolt six (6) upper manifold retaining bolts to separate the upper manifold and throttle body as an assembly from the lower manifold. Ensure the gasket is in place during installation, attach new gasket(s) onto lower intake mounting face, and snug up air intake plenum with throttle body assembly by using six (6) upper manifold retaining bolts right up to the recommended torque value.

Genuine Ford Crown Victoria Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Intake Manifolds found

View related parts
Ford Crown Victoria Kit - Manifold Hardware
Part Number: 1W7Z-9424-AAA
$322.05 MSRP: $475.00
You Save: $152.95 (33%)
ADD TO CART
Product Specifications
- Replaced by: PU7Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Manifold Assembly - Inlet
Part Number: 3W7Z-9424-AD
$322.05 MSRP: $475.00
You Save: $152.95 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assy - Inlet
- Manufacturer Note: No serviceable gaskets between intake and water crossover
- Replaced by: PU7Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT
View related parts
Ford Crown Victoria Manifold Assembly - Inlet
Part Number: 1W7Z-9424-AA
$322.05 MSRP: $475.00
You Save: $152.95 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assy - Inlet
- Replaced by: PU7Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Manifold Assembly - Inlet
Part Number: F8AZ-9424-AA
$854.52 MSRP: $1187.07
You Save: $332.55 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assy - Inlet
- Manufacturer Note: Compressed natural gas, NGV ONLY
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Manifold Assembly - Inlet 0
Part Number: 6W7Z-9424-AA
Product Specifications
- Other Name: Manifold Assy - Inlet; Intake Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Kit - Manifold Hardware
Part Number: F8AZ-9424-BAA
$0.00
Product Specifications
- Manufacturer Note: Kit to replace plastic intake. Includes intake, alt. brace, 2 bolts, gaskets & o-ring., With 4g alternator(straight fins in case)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Manifold Assembly - Inlet
Part Number: 9W7Z-9424-A
$345.78 MSRP: $510.00
You Save: $164.22 (33%)
Product Specifications
- Other Name: Manifold Assy - Inlet; Intake Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Kit - Manifold Hardware
Part Number: F8AZ-9424-AAA
Product Specifications
- Manufacturer Note: Kit to replace plastic intake. Includes intake, alt. brace, 2 bolts, gaskets & o-ring.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Kit - Manifold Hardware
Part Number: F8AZ-9424-CA
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Manifold Assembly - Inlet
Part Number: F8AZ-9424-CB
$0.00
Product Specifications
- Other Name: Manifold Assy - Inlet
- Manufacturer Note: Used to replace intake manifold with aluminum cross over.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Kit - Manifold Hardware
Part Number: 1W7Z-9424-BA
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W

Ford Crown Victoria Intake Manifold Parts Questions & Experts Answers

Kit - Manifold Hardware
F8AZ-9424-AAA
Q: How do you check and replace fuel injectors, Fuel Pressure Regulator,Fuel Rail,Intake Manifold,Throttle Body and Throttle Position Sensor on a Ford Crown Victoria 5.0L engine?
A: The first step in removing the air intake plenum and throttle body on a 5.0L engine involves disconnecting the negative battery cable. Also, unplug electrical connectors at the air bypass valve, throttle position sensor, and EGR position sensor. Disconnect the Accelerator Cable and transmission linkage from the throttle body assembly, remove the accelerator cable/TV cable bracket from the intake manifold, and label and detach vacuum lines from the upper intake manifold vacuum tree, EGR valve, and fuel pressure regulator. Make sure to disconnect the PCV system or any canister purge line if it is present and also downsize the water pipes of spacer coolant lines for EGR. Unbolt six (6) upper manifold retaining bolts to separate the upper manifold and throttle body as an assembly from the lower manifold. Ensure the gasket is in place during installation, attach new gasket(s) onto lower intake mounting face, and snug up air intake plenum with throttle body assembly by using six (6) upper manifold retaining bolts right up to the recommended torque value.

Related Ford Crown Victoria Parts

Browse by Year

2011 Intake Manifold 2010 Intake Manifold 2009 Intake Manifold 2008 Intake Manifold 2007 Intake Manifold 2006 Intake Manifold 2005 Intake Manifold 2002 Intake Manifold 2001 Intake Manifold 2000 Intake Manifold 1999 Intake Manifold 1998 Intake Manifold 1997 Intake Manifold 1996 Intake Manifold