How to replace the Door Handle,Door Latch and Door Lock Cylinder on Ford Edge?

To replace the outside door handle lever, begin by removing the trim cap for the outside handle retaining screw and loosening the screw without removing it. Next, take off the cover from the outside handle and pull the handle out and to the rear to disengage it from the handle reinforcement inside the door. Inspect the outside door handle seals and replace them if they are cracked or deteriorated. For the inside door handle, remove the door trim panel, disengage the handle from the regulator module, and disconnect the actuator by prying out the bushing, aligning the cable with the slot in the handle lever to pull out the cable end plug. For the outside door handle reinforcement, first remove the outside door handle lever, then the door trim panel and the power window regulator. Disengage the upper and lower actuating rods, disconnect the keyless entry pad harness retaining clip, and remove the handle reinforcement. When dealing with the door lock cylinder, note that a new cylinder cannot be simply installed; instead, discard the old one and build a new unit using a lock repair package from the dealer. Remove the outside door handle, disengage the release tab, and install the rebuilt lock cylinder by aligning the D-slot. For the liftgate latch, remove the trim panel, disconnect the electrical connector, and remove the latch bolts. The installation process is the reverse of removal, followed by de-initialization/initialization procedures. For power release switch models, remove the liftgate trim panel, disconnect the electrical connector, and remove the switch molding screws to take out the switch. For manual release switch models, remove the trim panel, disconnect the electrical connector, and remove the switch molding nuts before taking out the switch. For the keyless entry pad on 2014 and earlier models, remove the upper trim cap, release the clip holding the keypad, and disconnect the electrical connector. For 2015 and later models, the keyless entry pad is integrated into the door upper trim panel; remove the exterior mirror, lower the window, and take off the door panel and moulding fasteners. Disconnect the key pad entry electrical connector and remove the door upper trim panel fasteners, pulling the harness out through the window opening. The installation process is the reverse of removal for all components.

Genuine Ford Edge Door Lock Cylinder

Door Lock Cylinder Tumbler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Door Lock Cylinders found

View related parts
Ford Edge Cylinder Assembly - Lock
Part Number: 8E5Z-5421991-B
$63.98 MSRP: $93.53
You Save: $29.55 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Position: Driver Side
- Replaces: 5L8Z-7821991-AA, 6E5Z-5421991-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Cylinder Assembly - Lock
Part Number: DS7Z-5421991-E
$71.70 MSRP: $130.60
You Save: $58.90 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock; Lock Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2019 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS) , 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Cylinder Assembly - Lock
Part Number: DS7Z-5421991-C
$88.12 MSRP: $128.83
You Save: $40.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder, Lock Cylinder Assy
- Position: Driver Side Only
- Replaces: DS7Z-5421991-G, DS7Z-5421991-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS), 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 2.7 L GAS, 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Lockset - Complete Vehicle
Part Number: ES7Z-5422050-B
$62.18 MSRP: $90.90
You Save: $28.72 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS) , 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Cylinder Assembly - Lock
Part Number: DS7Z-5421991-D
$88.12 MSRP: $128.83
You Save: $40.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Position: Driver Side Only
- Replaced by: DS7Z-5421991-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2019 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS) , 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Cylinder Assembly - Lock
Part Number: 6E5Z-5421991-B
$63.98 MSRP: $93.53
You Save: $29.55 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Position: Driver Side
- Replaced by: 8E5Z-5421991-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Ford Edge | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Lockset - Complete Vehicle
Part Number: FR3Z-6322050-A
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2016 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS) , 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Lockset - Complete Vehicle
Part Number: GT4Z-5422050-A
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2017 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS) , 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive

Ford Edge Door Lock Cylinder

Door Lock Cylinder is an important part situated in front doors of Ford Edge vehicles which controls locking and unlocking of the doors by the help of the car key. Hinged doors are crucial to obtain and maintain control of the vehicle as well as gain entry into the cabin part of the vehicle. While many contemporary cars tend not to use this component, it is still used on the Ford Edge, especially since they are shaped and may end up getting damaged due to frequent use. When it is worn out this results in problems in the locking and unlocking of the doors and the key might get stuck on the Door Lock Cylinder. For efficiency, durability and security of this Ford Edge, the Door Lock Cylinder needs to be replaced as soon as one notices that it has become faulty. Maintenance work makes sure that the locking system works effectively thus ensuring the safety of the car and its occupants.

We provide a wide range of Ford Edge Door Lock Cylinder at the best prices possible. If you need Ford Edge Door Lock Cylinder, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Edge Door Lock Cylinder Parts Questions & Experts Answers

Cylinder Assembly - Lock
8E5Z-5421991-B
Q: How to replace the Door Handle,Door Latch and Door Lock Cylinder on Ford Edge?
A: To replace the outside door handle lever, begin by removing the trim cap for the outside handle retaining screw and loosening the screw without removing it. Next, take off the cover from the outside handle and pull the handle out and to the rear to disengage it from the handle reinforcement inside the door. Inspect the outside door handle seals and replace them if they are cracked or deteriorated. For the inside door handle, remove the door trim panel, disengage the handle from the regulator module, and disconnect the actuator by prying out the bushing, aligning the cable with the slot in the handle lever to pull out the cable end plug. For the outside door handle reinforcement, first remove the outside door handle lever, then the door trim panel and the power window regulator. Disengage the upper and lower actuating rods, disconnect the keyless entry pad harness retaining clip, and remove the handle reinforcement. When dealing with the door lock cylinder, note that a new cylinder cannot be simply installed; instead, discard the old one and build a new unit using a lock repair package from the dealer. Remove the outside door handle, disengage the release tab, and install the rebuilt lock cylinder by aligning the D-slot. For the liftgate latch, remove the trim panel, disconnect the electrical connector, and remove the latch bolts. The installation process is the reverse of removal, followed by de-initialization/initialization procedures. For power release switch models, remove the liftgate trim panel, disconnect the electrical connector, and remove the switch molding screws to take out the switch. For manual release switch models, remove the trim panel, disconnect the electrical connector, and remove the switch molding nuts before taking out the switch. For the keyless entry pad on 2014 and earlier models, remove the upper trim cap, release the clip holding the keypad, and disconnect the electrical connector. For 2015 and later models, the keyless entry pad is integrated into the door upper trim panel; remove the exterior mirror, lower the window, and take off the door panel and moulding fasteners. Disconnect the key pad entry electrical connector and remove the door upper trim panel fasteners, pulling the harness out through the window opening. The installation process is the reverse of removal for all components.

Related Ford Edge Parts

Browse by Year

2024 Door Lock Cylinder 2023 Door Lock Cylinder 2022 Door Lock Cylinder 2021 Door Lock Cylinder 2020 Door Lock Cylinder 2019 Door Lock Cylinder 2018 Door Lock Cylinder 2017 Door Lock Cylinder 2016 Door Lock Cylinder 2015 Door Lock Cylinder 2014 Door Lock Cylinder 2013 Door Lock Cylinder 2012 Door Lock Cylinder 2011 Door Lock Cylinder 2010 Door Lock Cylinder 2009 Door Lock Cylinder 2008 Door Lock Cylinder 2007 Door Lock Cylinder