How do you remove and install the key lock cylinder and ignition switch on Ford Edge?

Disconnect the cable from the negative terminal of the battery. Remove the instrument cluster upper and lower trim panels. Using a small screwdriver, detach the tabs securing the Passive Anti-Theft System (PATS) transceiver to the ignition lock cylinder housing, then pull the transceiver off the housing and disconnect the electrical connector. Insert the ignition key into the ignition lock cylinder and turn it to the ACC position. Insert an awl or suitable tool into the hole in the underside of the ignition lock cylinder, then depress the ignition lock cylinder retaining tab and remove the ignition lock cylinder. To install the ignition lock cylinder, insert it into the lock cylinder housing and push it in until it clicks into place. Verify that the ignition switch operates correctly in the OFF, ACC, RUN, and START positions, with installation being the reverse of removal. For 2014 and earlier models, do not remove the ignition switch and the ignition lock cylinder at the same time to avoid damaging the steering column. Remove the fasteners securing the ignition lock cylinder housing, disconnect the electrical connector for the PATS transceiver, and disconnect the electrical connector from the ignition switch. Depress the release tabs to detach the ignition switch from the ignition lock cylinder, ensuring that it snaps into place during installation, which is otherwise the reverse of removal. For 2015 and later keyless entry models, carefully pry out the left-side center air register from the instrument panel using a trim tool, disconnect the electrical connector from the push start ignition switch, and from the back side of the instrument panel, depress the two retaining tabs on the switch then push the ignition switch button out of the instrument panel.

Genuine Ford Edge Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Ignition Switches found

View related parts
Ford Edge Switch Assembly - Ignition
Part Number: DG9Z-11572-A
$59.95 MSRP: $99.09
You Save: $39.14 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Ignition; Ignition Switch
- Replaces: 98AZ-11572-A, YS4Z-11572-AC, SW-6343
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2019 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS), 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Switch Assembly - Ignition
Part Number: 98AZ-11572-A
$59.95 MSRP: $99.09
You Save: $39.14 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Ignition
- Replaced by: DG9Z-11572-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2013 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Switch Assembly - Solenoid Control
Part Number: DG9Z-10B776-AB
$46.40 MSRP: $66.67
You Save: $20.27 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Solenoid Control; Power Switch, Start Button
- Replaces: DG9Z-10B776-AC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS), 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 2.7 L GAS, 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Switch - Ignition Impulse Counting
Part Number: BT4Z-12A145-A
$69.30 MSRP: $105.00
You Save: $35.70 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Switch Housing
- Manufacturer Note: Ignition Lock Service Asy.
- Replaces: 8A5Z-12A145-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive

Ford Edge Ignition Switch

The Ignition Switch is incorporated in Ford Edge to act as a fundamental piece in the ignition and charging circuitry necessary for starting the automobiles' engine as well as other circuits such as radio and power windows among others. By simply using a key, button or remote to turn on the Ignition Switch the computer is induced to perform certain routines to start up different systems thus powering the engine on. Throughout the years of the Ford Edge models they have featured different styles of the Ignition Switch where the traditional key switch has evolved to advanced keyless Ignition Switch that features push buttons. While the former can be opened and started only with the help of a specific key, the latter still requires the interaction of the transponder signal to start the system. However, as with any consequent model year, the fundamental operation of the Ignition Switch has progressively aimed at delivering a quality start of the Ford Edge's engine, as well as the loading of the corresponding systems.

We provide a wide range of Ford Edge Ignition Switch at the best prices possible. If you need Ford Edge Ignition Switch, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Edge Ignition Switch Parts Questions & Experts Answers

Switch Assembly - Ignition
98AZ-11572-A
Q: How do you remove and install the key lock cylinder and ignition switch on Ford Edge?
A: Disconnect the cable from the negative terminal of the battery. Remove the instrument cluster upper and lower trim panels. Using a small screwdriver, detach the tabs securing the Passive Anti-Theft System (PATS) transceiver to the ignition lock cylinder housing, then pull the transceiver off the housing and disconnect the electrical connector. Insert the ignition key into the ignition lock cylinder and turn it to the ACC position. Insert an awl or suitable tool into the hole in the underside of the ignition lock cylinder, then depress the ignition lock cylinder retaining tab and remove the ignition lock cylinder. To install the ignition lock cylinder, insert it into the lock cylinder housing and push it in until it clicks into place. Verify that the ignition switch operates correctly in the OFF, ACC, RUN, and START positions, with installation being the reverse of removal. For 2014 and earlier models, do not remove the ignition switch and the ignition lock cylinder at the same time to avoid damaging the steering column. Remove the fasteners securing the ignition lock cylinder housing, disconnect the electrical connector for the PATS transceiver, and disconnect the electrical connector from the ignition switch. Depress the release tabs to detach the ignition switch from the ignition lock cylinder, ensuring that it snaps into place during installation, which is otherwise the reverse of removal. For 2015 and later keyless entry models, carefully pry out the left-side center air register from the instrument panel using a trim tool, disconnect the electrical connector from the push start ignition switch, and from the back side of the instrument panel, depress the two retaining tabs on the switch then push the ignition switch button out of the instrument panel.