How do you remove and install the ignition switch and key lock cylinder on Ford F-150?

Disconnect the cable from the negative terminal of the battery. Remove the upper and lower steering column covers. For 2004 through 2008 models, remove the multi-function switch, disconnect the electrical connector from the ignition switch by depressing the release tab and pulling out the connector, and then remove the ignition switch by depressing the release tabs on the top and bottom and pulling it out to the left. Installation is the reverse of removal. For 2009 and 2010 models, position the steering column in the full-down position if equipped with manual tilt steering wheels, remove the steering wheel, detach the wiring harness retainers from the steering column, disconnect the electrical connectors from the ignition switch, multifunction switch, clockspring, Passive Anti-Theft System (PATS), ignition key, and interlock actuator if equipped, remove the three bolts and multifunction switch carrier if applicable, remove the ignition switch mounting screw, and then remove the switch. Installation is the reverse of removal. For 2011 and later models, disconnect the electrical connector from the ignition switch, detach the ignition switch from the steering column by depressing the release tabs and pulling it out, and installation is the reverse of removal. To remove the Ignition Lock Cylinder, first remove the steering wheel and steering column covers, then remove the Passive Anti-Theft System (PATS) transceiver by depressing the release tab, pulling off the electrical connector, unscrewing the bolt, and removing the transceiver. Insert the ignition key into the Ignition Lock Cylinder, turning it to the ON position for 2004 through 2008 models or to the ACC position for 2009 and later models. Insert an awl or small screwdriver into the hole on the underside of the Ignition Lock Cylinder, depress the retaining tab, and remove the Ignition Lock Cylinder. Installation is the reverse of removal.

Genuine Ford F-150 Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Ignition Lock Cylinders found

View related parts
Ford F-150 Cylinder Ignition
Part Number: AU5Z-11582-A
$97.45 MSRP: $133.16
You Save: $35.71 (27%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2014 Ford F-150 | 6 Cyl 3.5L DOHC TIVCT, 6 Cyl 3.7L PFI NA, 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI, 8 Cyl 5.0L MOD DOHC SEFI NA, 8 Cyl 5.4L, 8 Cyl 6.2L OHC NA | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Lock Cylinder With Keys
Part Number: FL3Z-11582-B
$46.06 MSRP: $73.45
You Save: $27.39 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Replaces: FL3Z-11582-A, SW-7611
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2020 Ford F-150 | 6 Cyl 2.7 L GAS, 6 Cyl 2.7L, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.0L 4V DOHC TC DSL-LION B, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3L Duratec, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L GTDI, 8 Cyl 5.0 L FLEX, 8 Cyl 5.0L Coyote, 8 Cyl 5.0L MOD DOHC SEFI NA | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: 4L3Z-11582-BB
$79.09 MSRP: $130.73
You Save: $51.64 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: AU5Z-11582-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2010 Ford F-150 | 6 Cyl 4.2L OHV EFI, 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI, 8 Cyl 4.6L Windsor SOHC EFI, 8 Cyl 5.4L, 8 Cyl 6.2L OHC NA | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 LOCK CYLINDER WITH KEYS
Part Number: ML3Z-11582-A
$88.92 MSRP: $130.00
You Save: $41.08 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder & Key, Ignition Lock Cylinder
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2022 Ford F-150 | 6 Cyl 3.5 L GAS
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: E5TZ-11582-A
Product Specifications
- Replaces: E4TZ-11582-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1981-1991 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L | 3AT C5, 3AT C6, 3MT, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3AZ-11582-A
Product Specifications
- Other Name: LOCKSET - COMPLETE V
- Replaced by: F3DZ-11582-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3AZ-11582-D
Product Specifications
- Other Name: LOCKSET - COMPLETE V
- Replaced by: F3DZ-11582-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3DZ-11582-A
Product Specifications
- Replaces: F1DZ-11582-A, F1AZ-11582-A, F3AZ-11582-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1996 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3DZ-11582-B
Product Specifications
- Other Name: Ignition Lock Cylinder, Lock Cylinder
- Replaces: F1AZ-11582-B, F3AZ-11582-B, F1DZ-11582-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1996 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3DZ-11582-C
Product Specifications
- Other Name: Ignition Lock Cylinder
- Replaces: F3AZ-11582-C, F1DZ-11582-C, F1AZ-11582-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1996 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: 4L3Z-11582-BC
Product Specifications
- Manufacturer Note: Lock Service Pack - Ignition
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford F-150 | 6 Cyl 4.2L OHV EFI, 8 Cyl 4.6L Romeo SOHC EFI, 8 Cyl 4.6L Windsor SOHC EFI, 8 Cyl 5.4L | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: E1TZ-1021984-A
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1981-1991 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L | 3AT C5, 3AT C6, 3MT, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Cylinder & Key Set Ignition Front
Part Number: E1TZ1022050A
Product Specifications
- Other Name: Wrench - Wheel Nut
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980 Ford F-150 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 3MT, 4MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: E4TZ-11582-B
Product Specifications
- Other Name: Ignition Lock Cylinder
- Replaced by: E5TZ-11582-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1981-1984 Ford F-150 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L | 3AT C5, 3AT C6, 3MT, 4AT AOD, 4MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F2TZ-1522050-A
Product Specifications
- Other Name: LOCKSET - COMPLETE V
- Manufacturer Note: F/D, IGN - bright
- Replaced by: F4TZ-1522050-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3AZ-11582-B
Product Specifications
- Other Name: LOCKSET - COMPLETE V
- Replaced by: F3DZ-11582-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3AZ-11582-C
Product Specifications
- Other Name: LOCKSET - COMPLETE V
- Replaced by: F3DZ-11582-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3AZ-11582-E
Product Specifications
- Other Name: LOCKSET - COMPLETE V
- Replaced by: F3DZ-11582-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3DZ-11582-D
Product Specifications
- Other Name: Ignition Lock Cylinder
- Replaces: F1DZ-11582-D, F1AZ-11582-D, F3AZ-11582-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1996 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Lockset - Complete Vehicle
Part Number: F3DZ-11582-E
Product Specifications
- Other Name: Ignition Lock Cylinder
- Replaces: F1AZ-11582-E, F3AZ-11582-E, F1DZ-11582-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1996 Ford F-150 | 6 Cyl 3.8L, 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT

| Page 1 of 2 |Next >

1-20 of 22 Results

Ford F-150 Ignition Lock Cylinder

The Ignition Lock Cylinder in Ford F-150 is useful to start the engine of the car by letting the driver put the key then twist it. This mechanism belongs to the ignition switch which allows battery power flow to the required circuits when the key is turned to START position. In the past, the Ford F-150 vehicles came with more standard column-mounted ignition lock cylinders in order to increase the vehicles' security and safety features. With time, changes have occurred and new Ford F-150 models come with what is known as the keyless ignition system that uses a fob that communicates with the car's computer. Not only this change makes it more convenient but also it reduces the number of change-overs, and that is why it is more reliable. However, conventional ignition lock cylinders have not been totally eliminated as they can foul up and cause starting problems or sudden stops. In general, the Ignition Lock Cylinder remains an essential component part to Ford F-150 vehicles functions and security.

We provide a wide range of Ford F-150 Ignition Lock Cylinder at the best prices possible. If you need Ford F-150 Ignition Lock Cylinder, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford F-150 Ignition Lock Cylinder Parts Questions & Experts Answers

Cylinder Ignition
AU5Z-11582-A
Q: How do you remove and install the ignition switch and key lock cylinder on Ford F-150?
A: Disconnect the cable from the negative terminal of the battery. Remove the upper and lower steering column covers. For 2004 through 2008 models, remove the multi-function switch, disconnect the electrical connector from the ignition switch by depressing the release tab and pulling out the connector, and then remove the ignition switch by depressing the release tabs on the top and bottom and pulling it out to the left. Installation is the reverse of removal. For 2009 and 2010 models, position the steering column in the full-down position if equipped with manual tilt steering wheels, remove the steering wheel, detach the wiring harness retainers from the steering column, disconnect the electrical connectors from the ignition switch, multifunction switch, clockspring, Passive Anti-Theft System (PATS), ignition key, and interlock actuator if equipped, remove the three bolts and multifunction switch carrier if applicable, remove the ignition switch mounting screw, and then remove the switch. Installation is the reverse of removal. For 2011 and later models, disconnect the electrical connector from the ignition switch, detach the ignition switch from the steering column by depressing the release tabs and pulling it out, and installation is the reverse of removal. To remove the Ignition Lock Cylinder, first remove the steering wheel and steering column covers, then remove the Passive Anti-Theft System (PATS) transceiver by depressing the release tab, pulling off the electrical connector, unscrewing the bolt, and removing the transceiver. Insert the ignition key into the Ignition Lock Cylinder, turning it to the ON position for 2004 through 2008 models or to the ACC position for 2009 and later models. Insert an awl or small screwdriver into the hole on the underside of the Ignition Lock Cylinder, depress the retaining tab, and remove the Ignition Lock Cylinder. Installation is the reverse of removal.

Related Ford F-150 Parts

Browse by Year