×
- Live Chat
- 1-888-788-9341
My Garage
My Account
Cart
Genuine Ford Ranger Idle Control Valve
IACV- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
18 Idle Control Valves found
Ford Ranger Valve Assy - Throttle Air By-Pass
Part Number: 1S7Z-9F715-AA$72.60 MSRP: $120.00You Save: $47.40 (40%)Ships in 1-2 Business Days
Ford Ranger Valve Assy - Throttle Air By-Pass
Part Number: 4F1Z-9F715-AA$67.43 MSRP: $111.45You Save: $44.02 (40%)Ships in 1-2 Business Days
Ford Ranger Valve Assembly - Throttle
Part Number: E9AZ-9F715-A$67.56 MSRP: $109.45You Save: $41.89 (39%)
Ford Ranger Valve Assembly - Throttle Air By-Pass
Part Number: 2L5Z-9F715-BA$97.13 MSRP: $160.55You Save: $63.42 (40%)Ships in 1-2 Business Days
Ford Ranger Valve Assembly - Throttle Air By-Pass
Part Number: XL2Z-9F715-BA$88.33 MSRP: $146.00You Save: $57.67 (40%)
Ford Ranger Valve Assembly - Throttle Air By-Pass
Part Number: F67Z-9F715-AA$70.27 MSRP: $139.64You Save: $69.37 (50%)Ships in 1-3 Business Days
Ford Ranger Valve Assembly - Throttle Air By-Pass
Part Number: 1F1Z-9F715-AA$67.43 MSRP: $111.45You Save: $44.02 (40%)Ships in 1-2 Business Days
Ford Ranger Valve Assembly - Throttle Air By-Pass
Part Number: F69Z-9F715-AA$79.97 MSRP: $132.18You Save: $52.21 (40%)Ships in 1-2 Business DaysFord Ranger Valve Assembly - Throttle Air By-Pass
Part Number: F68Z-9F715-DA$84.81 MSRP: $140.18You Save: $55.37 (40%)Ships in 1-2 Business Days
Ford Ranger Valve Assembly - Throttle Air By-Pass
Part Number: F5TZ-9F715-B$84.13 MSRP: $134.18You Save: $50.05 (38%)Ships in 1-3 Business Days
Ford Ranger Valve Assy - Throttle Air By-Pass
Part Number: F5OZ-9F715-AB$68.29 MSRP: $108.91You Save: $40.62 (38%)
Ford Ranger Idle Control Valve
Also in the Ford Ranger cars, there is the Idle Control Valve; its function is to control the amount of air that is allowed to pass over the throttle plate at idle. This blend with the engine control unit and helps in providing good situations in idle position and particularly not stalling during the load alterations. The valve commonly contains an electric actuator to control the valve and an airflow, which is modified using a linear servo motor to keeping the car at a constant idle speed. Different designs of Idle Control Valves have been used in the different models and generations of the Ford Ranger with a special emphasis on endurance and power. As for the above valves, they are produced to endure wear, but they may face a few problems, for instance, get jammed by dirt or dust, which in turn causes the engine to idle erratically. Cleaning and maintaining, the Idle Control Valve should therefore be cleaned regularly so that it does not get spoilt by various components thus requiring replacement.
We provide a wide range of Ford Ranger Idle Control Valve at the best prices possible. If you need Ford Ranger Idle Control Valve, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.
Ford Ranger Idle Control Valve Parts Questions & Experts Answers
- Q: How to replace the Brake Light Switch,Camshaft Position Sensor,Coolant Temperature Sensor,Crankshaft Position Sensor,Cylinder Head Temperature Sensor,Idle Control Valve,Intake Manifold Temperature Sensor,Mass Air Flow Sensor,Oxygen Sensors,Throttle Position Sensor and Vehicle Speed Sensor on 1993-2011 Ford Ranger?A: To replace Engine Coolant Temperature (ECT) sensor for 2011 models, drain the cooling system, wrap new sensor's threads with Teflon sealing tape, unplug the electrical connector and remove the sensor by thermostat housing. For 2001 and newer 2.3L models a Cylinder Head Temperature (CHT) sensor is used; disconnect battery, expose electrical connector, unscrew and remove CHT sensor. The Oxygen Sensor replacement involves disconnecting the battery, raising the vehicle and removing the O2 sensor using proper tool, apply anti-seize compound to new threads and tighten it into place. Throttle Position Sensor (TPS) replacement requires disconnecting of battery, removal of throttle body cover, unfastening of TPS and ensure proper alignment during installation. Replacing Mass Airflow Sensor (MAF) means; firstly you need to disconnect battery from its terminal, then undo electrical connection between MAF sensor's plug-in connectors followed by taking off MAF sensor itself lastly install new one with a fresh gasket on 2011 models. To control air conditioning clutch relay PCM controls this while checking fuses for any malfunctioning Air conditioning clutch control means that PCM operates this clutch relay as you verify fuses for defects which may be interfering with idle speed quality in your vehicle at all times Vehicle Speed Sensor (VSS) change applies to those vehicles made before 1997; therefore when replacing it you are supposed to detach an electric connector from a particular component installed in a car under consideration while removing retaining bolt also do not forget about reversing above mentioned process Intake Manifold Temperature Sensor replacement includes disconnecting the battery, unplugging the intake manifold temperature sensor connector, removing the IMTS from intake manifold Idle Air Control (IAC) valve replacement requires disconnection of battery power supply followed by taking IAC valve cover out where electronic wires should be disconnected only after unscrewing screws Power steering pressure switch inspection comprises of checking fuses as well as circuits that might be affecting idle quality in your automobile Camshaft Position (CMP) sensor replacement varies with model, which may include but not limited to separating the battery, loosening electrical connector, removing sensor then fitting the new one properly. Crankshaft Position (CKP) sensor replacement includes disconnecting battery, removal of things like accessory drive belt or alternator, unscrewing of the sensor and installing new one with specific alignment procedures for different models Brake Light Switch or Brake Pedal Position (BPP) Sensor information informs about its purpose that is to show whether brakes are applied or not and it is located on brake pedal assembly.
Related Ford Ranger Parts
Browse by Year
2011 Idle Control Valve 2010 Idle Control Valve 2009 Idle Control Valve 2008 Idle Control Valve 2007 Idle Control Valve 2006 Idle Control Valve 2005 Idle Control Valve 2004 Idle Control Valve 2003 Idle Control Valve 2002 Idle Control Valve 2001 Idle Control Valve 2000 Idle Control Valve 1999 Idle Control Valve 1998 Idle Control Valve 1997 Idle Control Valve 1996 Idle Control Valve 1995 Idle Control Valve 1994 Idle Control Valve 1993 Idle Control Valve 1992 Idle Control Valve 1991 Idle Control Valve 1990 Idle Control Valve 1989 Idle Control Valve 1988 Idle Control Valve 1987 Idle Control Valve 1986 Idle Control Valve 1985 Idle Control Valve 1984 Idle Control Valve 1983 Idle Control Valve