How to remove and install an intake manifold on Lincoln Town Car Overhead valve (OHV)engines?

To remove the intake manifold, you need to drain the cooling system and disconnect various hoses and cables. To identify and disconnect electrical and vacuum connectors. This requires removing the distributor to relieve fuel system pressure while disconnecting the fuel supply and return lines. For carbureted applications, this step will also require removal of the carburetor. It may be necessary to loosen clamps on these hoses and remove them from their connection points. The air intake plenum must be removed by unbolting coolant pipes if it is present. You should then proceed by loosening the lower intake manifold bolts and nuts as well as removing them completely. In this way, one can lift up the manifold checking that all bolts have been undone too. Use guide pins for installation together with sealant and gasket adhesive. Gaskets as well as end seals are required after cleaning mating surfaces.

How to remove and install an intake manifold on Lincoln Town Car Overhead cam(OHC) engine?

First of all, here is how you can remove the plastic intake manifold on the 1996 models. First, relieve the fuel system pressure, drain the cooling system, and disconnect the negative battery cable. The initial things to do are to remove the drivebelt, radiator, heater, water pump bypass hoses, thermostat housing, air inlet tube, and vacuum lines. These components include an accelerator cable, automatic transmission cable, speed control linkage, ignition wire brackets, boots, wires, alternator strap tightener bracket, and tightening nut. Next remove the upper intake manifold by taking apart the wire loom bracket, raising the vehicle, and disconnecting the EGR tube along with oil pressure sending unit electrical connector and fuel supply and return lines. Lastly, carefully lift the lower intake manifold from the cylinder heads by loosening and then removing bolts and nuts. Reassemble the components to complete installation.

Genuine Lincoln Town Car Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Intake Manifolds found

View related parts
Lincoln Town Car Kit - Manifold Hardware
Part Number: 1W7Z-9424-AAA
$322.05 MSRP: $475.00
You Save: $152.95 (33%)
ADD TO CART
Product Specifications
- Replaced by: PU7Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Manifold Assembly - Inlet
Part Number: 3W7Z-9424-AD
$322.05 MSRP: $475.00
You Save: $152.95 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assy - Inlet
- Manufacturer Note: No serviceable gaskets between intake and water crossover
- Replaced by: PU7Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Lincoln Town Car | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R70W (AODE), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R70E W/TSS*S/V, 4-Speed Automatic Transmission AODEW/4R75E W/TSS S/V, 4-Speed Automatic Transmission NAAO AODEW/4R70W*S/VIL, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Town Car Manifold Assembly - Inlet
Part Number: 1W7Z-9424-AA
$322.05 MSRP: $475.00
You Save: $152.95 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assy - Inlet
- Replaced by: PU7Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Manifold Assembly - Inlet 0
Part Number: 6W7Z-9424-AA
Product Specifications
- Other Name: Manifold Assy - Inlet; Intake Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Lincoln Town Car | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R70W (AODE), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R70E W/TSS*S/V, 4-Speed Automatic Transmission AODEW/4R75E W/TSS S/V, 4-Speed Automatic Transmission NAAO AODEW/4R70W*S/VIL, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Town Car Kit - Manifold Hardware
Part Number: F8AZ-9424-BAA
$0.00
Product Specifications
- Manufacturer Note: Kit to replace plastic intake. Includes intake, alt. brace, 2 bolts, gaskets & o-ring., With 4g alternator(straight fins in case)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Manifold Assembly - Inlet
Part Number: 9W7Z-9424-A
$345.78 MSRP: $510.00
You Save: $164.22 (33%)
Product Specifications
- Other Name: Manifold Assy - Inlet; Intake Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Lincoln Town Car | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R70W (AODE), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R70E W/TSS*S/V, 4-Speed Automatic Transmission AODEW/4R75E W/TSS S/V, 4-Speed Automatic Transmission NAAO AODEW/4R70W*S/VIL, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Town Car Kit - Manifold Hardware
Part Number: F8AZ-9424-AAA
Product Specifications
- Manufacturer Note: Kit to replace plastic intake. Includes intake, alt. brace, 2 bolts, gaskets & o-ring.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Kit - Manifold Hardware
Part Number: F8AZ-9424-CA
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Manifold Assembly - Inlet
Part Number: F8AZ-9424-CB
$0.00
Product Specifications
- Other Name: Manifold Assy - Inlet
- Manufacturer Note: Used to replace intake manifold with aluminum cross over.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2000 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Kit - Manifold Hardware
Part Number: 1W7Z-9424-BA
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W

Lincoln Town Car Intake Manifold Parts Questions & Experts Answers

Kit - Manifold Hardware
1W7Z-9424-AAA
Q: How to remove and install an intake manifold on Lincoln Town Car Overhead valve (OHV)engines?
A: To remove the intake manifold, you need to drain the cooling system and disconnect various hoses and cables. To identify and disconnect electrical and vacuum connectors. This requires removing the distributor to relieve fuel system pressure while disconnecting the fuel supply and return lines. For carbureted applications, this step will also require removal of the carburetor. It may be necessary to loosen clamps on these hoses and remove them from their connection points. The air intake plenum must be removed by unbolting coolant pipes if it is present. You should then proceed by loosening the lower intake manifold bolts and nuts as well as removing them completely. In this way, one can lift up the manifold checking that all bolts have been undone too. Use guide pins for installation together with sealant and gasket adhesive. Gaskets as well as end seals are required after cleaning mating surfaces.
Kit - Manifold Hardware
F8AZ-9424-AAA
Q: How to remove and install an intake manifold on Lincoln Town Car Overhead cam(OHC) engine?
A: First of all, here is how you can remove the plastic intake manifold on the 1996 models. First, relieve the fuel system pressure, drain the cooling system, and disconnect the negative battery cable. The initial things to do are to remove the drivebelt, radiator, heater, water pump bypass hoses, thermostat housing, air inlet tube, and vacuum lines. These components include an accelerator cable, automatic transmission cable, speed control linkage, ignition wire brackets, boots, wires, alternator strap tightener bracket, and tightening nut. Next remove the upper intake manifold by taking apart the wire loom bracket, raising the vehicle, and disconnecting the EGR tube along with oil pressure sending unit electrical connector and fuel supply and return lines. Lastly, carefully lift the lower intake manifold from the cylinder heads by loosening and then removing bolts and nuts. Reassemble the components to complete installation.

Related Lincoln Town Car Parts

Browse by Year

2011 Intake Manifold 2010 Intake Manifold 2009 Intake Manifold 2008 Intake Manifold 2007 Intake Manifold 2006 Intake Manifold 2005 Intake Manifold 2004 Intake Manifold 2002 Intake Manifold 2001 Intake Manifold 2000 Intake Manifold 1999 Intake Manifold 1998 Intake Manifold 1997 Intake Manifold 1996 Intake Manifold