How to remove and install a radiator and coolant overflow tank on Mercury Grand Marquis?

Disconnect the cable from the negative battery terminal. Drain the cooling system, then disconnect the overflow hose, upper radiator hose, and lower radiator hose from the radiator. When removing the hoses, use a pliers to squeeze the tangs together and slide the clamp away from the end of the hose, then pull the hose from the radiator connection. If equipped with an automatic transmission or engine oil cooler, remove the cooler lines from the radiator. Use a flare-nut wrench on the fluid line and a back up wrench at the radiator fitting, to prevent damage to the transmission cooler lines when removing them from the radiator. Be careful not to damage the lines or fittings. Plug the ends of the disconnected lines to prevent leakage and stop dirt from entering the system. Have a drip pan ready to catch any spills. Remove the radiator mounting bolts. The cooling fan shroud is held in place by two bolts as is the radiator support bracket. Both the shroud and the bracket must be removed before the radiator can be removed. Unbolt the fan shroud and slip it back over the fan. Lift the radiator from the engine compartment. Take care not to contact the fan blades. Prior to installation of the radiator, replace any damaged hose clamps and radiator hoses. Radiator installation is the reverse of removal. When installing the radiator, make sure it seats properly in the lower saddles and that the rubber mounts are intact. Check to make sure that the rubber mounts are in place and in good shape, if they're beginning to deteriorate, now is the time to replace them. After installation, fill the system with the proper mixture of antifreeze, and also check the automatic transmission fluid level. Drain the engine coolant. Remove the coolant overflow hoses from the tank. Locate the two hoses attached to the Coolant Reservoir and disconnect them. Remove the bolts and detach the tank. Prior to installation, make sure the tank is clean and free of debris which could be drawn into the radiator. Wash it with soap and water if necessary. Installation is the reverse of removal.

Genuine Mercury Grand Marquis Radiator

Cooling Radiator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Radiators found

View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: 6W1Z-8005-AA
$0.00
Product Specifications
- Other Name: Radiator Assy
- Manufacturer Note: FROM 12/02/02
- Replaced by: H2MZ-8005-W
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT 4R70W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: 3W1Z-8005-AG
Product Specifications
- Other Name: Radiator Assy
- Manufacturer Note: #3W1H 8005-AG, BEFORE 12/02/02
- Replaced by: H2MZ-8005-Z
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: 3W1Z-8005-AH
Product Specifications
- Other Name: Radiator Assy
- Replaced by: H2MZ-8005-Z
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: 3W1Z-8005-AHCP
Product Specifications
- Other Name: Radiator Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Mercury Grand Marquis Cooling Unit Assembly
Part Number: 7W1Z-8T000-BCP
Product Specifications
- Other Name: Radiator Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Mercury Grand Marquis | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F1VY-8005-A
Product Specifications
- Other Name: RADIATOR ASY
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT, 4AT AOD, 4AT AODE
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F1VY-8005-C
Product Specifications
- Other Name: Radiator Assy; Radiator
- Manufacturer Note: Includes I.S. and attaching part(s)., with T/T
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT, 4AT AOD, 4AT AODE
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F2AZ-8005-A
Product Specifications
- Other Name: RADIATOR ASY
- Manufacturer Note: with T/T
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT, 4AT AODE
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F3AZ-8005-A
Product Specifications
- Other Name: RADIATOR ASY
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT, 4AT AODE
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F5VY-8005-A
Product Specifications
- Other Name: RADIATOR ASY
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT AODE
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F5VY-8005-B
Product Specifications
- Other Name: RADIATOR ASY
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT AODE
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F8VZ-8005-BA
Product Specifications
- Other Name: Radiator Assy
- Replaced by: H2MZ-8005-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Mercury Grand Marquis Radiator Assembly
Part Number: F8VZ-8005-BACP
Product Specifications
- Other Name: RADIATOR ASY
- Manufacturer Note: When ordering, refer to the Crash Part Truck Load Program Guidelines.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | 8 Cyl 4.6L | 4AT 4R70W

Mercury Grand Marquis Radiator

The Radiator of Mercury Grand Marquis automobiles is integral part of the cooling system of the vehicle, which provides heat sink for the engine. It works on the principles of a heat exchanger in which coolant from the engine is circulated through a core of fins and tubes to cool the air. Usually, such radiators are made of aluminum and there are possibilities of using copper/brass versions, while the location is at the frontal part of the car, so that the air flow is maximal. As for the equipped radiators, various types have been installed in the transmission of the Grand Marquis; these include standard and performance versions. Performance radiators has other upgrades like the use of lightweight aluminum, larger tubes to allow for more coolant flow and more number of fins to allow better heat dissipation. These bring a higher level of cooling efficiency and come in direct fit or universal type to meet the needed application. In total, the condition and performance of the car radiator are greatly important since the engine depends on it for the regulation of its temperature.

We provide a wide range of Mercury Grand Marquis Radiator at the best prices possible. If you need Mercury Grand Marquis Radiator, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Mercury Grand Marquis Radiator Parts Questions & Experts Answers

Radiator Assembly
F3AZ-8005-A
Q: How to remove and install a radiator and coolant overflow tank on Mercury Grand Marquis?
A: Disconnect the cable from the negative battery terminal. Drain the cooling system, then disconnect the overflow hose, upper radiator hose, and lower radiator hose from the radiator. When removing the hoses, use a pliers to squeeze the tangs together and slide the clamp away from the end of the hose, then pull the hose from the radiator connection. If equipped with an automatic transmission or engine oil cooler, remove the cooler lines from the radiator. Use a flare-nut wrench on the fluid line and a back up wrench at the radiator fitting, to prevent damage to the transmission cooler lines when removing them from the radiator. Be careful not to damage the lines or fittings. Plug the ends of the disconnected lines to prevent leakage and stop dirt from entering the system. Have a drip pan ready to catch any spills. Remove the radiator mounting bolts. The cooling fan shroud is held in place by two bolts as is the radiator support bracket. Both the shroud and the bracket must be removed before the radiator can be removed. Unbolt the fan shroud and slip it back over the fan. Lift the radiator from the engine compartment. Take care not to contact the fan blades. Prior to installation of the radiator, replace any damaged hose clamps and radiator hoses. Radiator installation is the reverse of removal. When installing the radiator, make sure it seats properly in the lower saddles and that the rubber mounts are intact. Check to make sure that the rubber mounts are in place and in good shape, if they're beginning to deteriorate, now is the time to replace them. After installation, fill the system with the proper mixture of antifreeze, and also check the automatic transmission fluid level. Drain the engine coolant. Remove the coolant overflow hoses from the tank. Locate the two hoses attached to the Coolant Reservoir and disconnect them. Remove the bolts and detach the tank. Prior to installation, make sure the tank is clean and free of debris which could be drawn into the radiator. Wash it with soap and water if necessary. Installation is the reverse of removal.