Make sure this part fits

Ford 1L2Z-6049-HA Cylinder Head Assembly

2001-2005 Ford Ranger 1L2Z6049HA

Customer Questions & Expert Answers (15)
Ford 1L2Z-6049-HA Cylinder Head Assembly
  • Part Description
    Cylinder Head Assy
  • Position
    Driver Side
  • Replaced By
    7U7Z-6049-B
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Ford
    Manufacturer Part Number1L2Z-6049-HA, 1L2Z6049HA
    Part DescriptionCylinder Head Assy
    Item Dimensions9.8 x 6.7 x 11.3 inches
    Item Weight30.70 Pounds
    PositionDriver Side
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerFord
    SKU1L2Z-6049-HA
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2001-2005 Ford Ranger6 Cyl 4.0L, 6 Cyl 4.0L SOHC EFI4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
  • Customer Questions & Expert Answers

    Q:
    Does the PN fit my vehicle? Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 1L2Z-6049-HA fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    How should the installed valve spring height be checked for the 2001 Ford Ranger? Posted by Customer
    A:
    1. Use a ruler graduated in 1/32-inch increments or a dial caliper. 2. Measure from the top of each spring seat or shim(s) to the bottom of the retainer.
    Posted by FordPartsGiant Specialist
    Q:
    What is the first step in the installation process for the 2006 Ford Ranger? Posted by Customer
    A:
    Thoroughly clean and inspect the gasket mating surfaces for cracks and warpage.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Cylinder Head
    Q:
    What must be removed before any repair procedures on the cylinder heads, timing chains, and jackshaft chains for the 1996 Ford Ranger? Posted by Customer
    A:
    The rocker arms and valve lash adjusters must be removed before any repair procedures on the cylinder heads, timing chains, and jackshaft chains.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after reinstalling all parts for the 2005 Ford Ranger? Posted by Customer
    A:
    Refill the cooling system.
    Posted by FordPartsGiant Specialist
    Q:
    How should heavy deposits on the valves be removed for the 2000 Ford Ranger? Posted by Customer
    A:
    Scrape off any heavy deposits that may have formed on the valves, then use a motorized wire brush to remove deposits from the valve heads and stems.
    Posted by FordPartsGiant Specialist
    Q:
    How can you prevent carbon from entering the gap between the pistons and bores for the 2011 Ford Ranger? Posted by Customer
    A:
    Smear a little grease in the gap. After cleaning each piston, use a small brush to remove all traces of grease and carbon from the gap, then wipe away the remainder with a clean rag.
    Posted by FordPartsGiant Specialist
    Q:
    How should the new gasket be positioned for the 2000 Ford Ranger? Posted by Customer
    A:
    Position the new gasket over the dowel pins in the block. Do not use a gasket sealer.
    Posted by FordPartsGiant Specialist
    Q:
    How should the valves be installed for the 2002 Ford Ranger? Posted by Customer
    A:
    Lubricate and install each valve, then install new seals on each of the valve stems. Don't twist or cock the seals during installation or they won't seat properly on the valve stems.
    Posted by FordPartsGiant Specialist
    Q:
    What is the first step in the removal process for the 2003 Ford Ranger? Posted by Customer
    A:
    Disconnect the negative cable from the battery.
    Posted by FordPartsGiant Specialist
    Q:
    What should be checked regarding valve springs for the 2008 Ford Ranger? Posted by Customer
    A:
    Each valve spring should be checked for wear and pits, and its free length should be measured and compared to specifications. Springs that are shorter than specified should not be reused.
    Posted by FordPartsGiant Specialist
    Q:
    How should the new gaskets be positioned for the 1993 Ford Ranger? Posted by Customer
    A:
    Position the new gaskets over the dowel pins on the block. Don't use sealant on the gaskets. Be sure the FRONT TOP marks are positioned correctly.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after installing the camshaft sprocket for the 2010 Ford Ranger? Posted by Customer
    A:
    Install the camshaft chain tensioning tool into the chain tensioner location on the left cylinder head.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done with the air conditioning compressor and power steering pump for the 2002 Ford Ranger? Posted by Customer
    A:
    Remove the air conditioning compressor from its mounting bracket and set it aside without disconnecting the hoses. Remove the bracket and set it, and the power steering pump, aside. Remove the alternator bracket mounting bolts and set the alternator and bracket aside.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done with the coolant hose connected to the EGR unit for the 2000 Ford Ranger? Posted by Customer
    A:
    Disconnect the coolant hose from the EGR unit and remove the hose from its bracket.
    Posted by FordPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part 1L2Z-6049-HA, the Right Choice

To ensure reliability, purchase Ford part # 1L2Z-6049-HA Cylinder Head Assembly. It is sometimes referred to as Ford Cylinder Head. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Ford Ranger models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford 1L2Z6049HA Cylinder Head Assembly. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Ford parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly