×
Contact Us Live Chat or 1-888-788-9341
My Garage
My Account
Cart
Search Bar
Search by Part Number, Part Name, or Vehicle
Track Order Help Center
Make sure this part fits

Ford F87Z-6049-BARM Cylinder Head Assembly

1995-2001 Ford F87Z6049BARM

Customer Questions & Expert Answers (21)
Ford F87Z-6049-BARM Cylinder Head Assembly
Ford F87Z-6049-BARM Cylinder Head Assembly
  • Part Description
    Cylinder Head Assy
  • Base No.
    6049
  • Replaces
    F5TZ-6049-B, F5TZ-6049-A, F87Z-6049-DA, F87Z-6049-CA
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers

  • Related Parts

    Shop for related parts for your vehicle

  • Product Specifications

    BrandGenuine Ford
    Base No.6049
    Manufacturer Part NumberF87Z-6049-BARM, F87Z6049BARM
    Part DescriptionCylinder Head Assy
    Other NamesCylinder Head
    Item Dimensions6.1 x 6.3 x 18.5 inches
    Item Weight41.00 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ReplacesF5TZ-6049-B, F5TZ-6049-A, F87Z-6049-DA, F87Z-6049-CA
    Require Quantity2
    ManufacturerFord
    SKUF87Z-6049-BARM
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65

  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1995-1997 Ford Aerostar6 Cyl 4.0L4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R55E
    1995-2001 Ford Explorer6 Cyl 4.0L4AT 4R44E, 4AT 4R55E, 4AT 4R70W, 4AT A4LD, 4AT AODE-E, 4AT AODE-W, 5AT 5R55E, 5MT
    1995-2000 Ford Ranger6 Cyl 4.0L4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R55E, 5MT

  • Customer Questions & Expert Answers

    Q:
    Is the the correct part for the attached VIN? Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if F87Z-6049-BARM fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    What special precautions should be taken when removing the left cylinder head for the 2006 Ford Ranger? Posted by Customer
    A:
    If removing the left cylinder head, detach the air conditioning compressor from the engine and place it out of the way. Do not disconnect any refrigerant lines. Also, detach the power steering pump and bracket and set them out of the way without disconnecting the power steering hoses.
    Posted by FordPartsGiant Specialist
    Q:
    What steps should be taken to install each valve if the head was not sent out for valve servicing for the 2007 Ford Ranger? Posted by Customer
    A:
    1. Lubricate and install each valve. 2. Install new seals on each of the valve stems, ensuring not to twist or cock the seals during installation.
    Posted by FordPartsGiant Specialist
    Q:
    How should the squareness of each spring be checked for the 2010 Ford Ranger? Posted by Customer
    A:
    Stand each spring on a flat surface and check it for squareness. If any of the springs are distorted or sagged, replace all of them with new parts.
    Posted by FordPartsGiant Specialist
    Q:
    What should be inspected on the cylinder head for the 2005 Ford Ranger? Posted by Customer
    A:
    Inspect the head for cracks, evidence of coolant leakage, and other damage. If cracks are found, consult an automotive machine shop for repair options.
    Posted by FordPartsGiant Specialist
    Q:
    What is the next step after removing the ground strap and throttle cable bracket for the 1993 Ford Ranger? Posted by Customer
    A:
    Remove the exhaust manifold(s).
    Posted by FordPartsGiant Specialist
    Q:
    What maintenance should be performed after installation for the 2000 Ford Ranger? Posted by Customer
    A:
    Change the engine oil and filter.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after removing the intake manifold for the 2010 Ford Ranger? Posted by Customer
    A:
    Remove the drivebelt.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done with the threads in the cylinder head bolt holes for the 2003 Ford Ranger? Posted by Customer
    A:
    Use a tap of the correct size to chase the threads in the cylinder head bolt holes.
    Posted by FordPartsGiant Specialist
    Q:
    What components need to be removed next for the 2003 Ford Ranger? Posted by Customer
    A:
    Remove the air cleaner outlet tube and air cleaner assembly.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Cylinder Head
    Q:
    What should be noted during reassembly for the 2005 Ford Ranger? Posted by Customer
    A:
    Reassembly is the reverse of removal, ensuring to install new gaskets and fasteners, and to check all hoses and wiring.
    Posted by FordPartsGiant Specialist
    Q:
    What should be removed after disconnecting electrical connectors and vacuum hoses for the 1997 Ford Ranger? Posted by Customer
    A:
    Remove the dipstick tube.
    Posted by FordPartsGiant Specialist
    Q:
    How should the cylinder head bolts be tightened for the 2003 Ford Ranger? Posted by Customer
    A:
    First hand tighten all bolts, then tighten them in five stages while following the proper sequence, using the angle gauge for the third and fourth tightening stages.
    Posted by FordPartsGiant Specialist
    Q:
    What additional steps are required for removing the left cylinder head for the 2010 Ford Ranger? Posted by Customer
    A:
    15. Disconnect the radio capacitor from the side of the ignition coil pack. 16. Remove the ignition coil assembly. 17. Remove the accessory bracket mounting bolts and position it off to the side. 18. Remove the hydraulic chain tensioner. 19. Remove the bolt from the camshaft sprocket, then remove the Torx bolt below it in the head, which secures the camshaft chain cassette to the head. 20. Remove the bolt holding the chain cassette to the head and pull up on the chain while slipping the sprocket out. Keep the slack out of the chain and tie it to the cassette with a large rubber band.
    Posted by FordPartsGiant Specialist
    Q:
    What if the head was sent out for valve servicing for the 2002 Ford Ranger? Posted by Customer
    A:
    If the head was sent out for valve servicing, the valves and related components will already be in place.
    Posted by FordPartsGiant Specialist
    Q:
    How should the margin width on each valve be measured for the 1999 Ford Explorer? Posted by Customer
    A:
    Measure the margin width on each valve. Any valve with a margin narrower than 1/32-inch will have to be replaced with a new one.
    Posted by FordPartsGiant Specialist
    Q:
    If the head was sent out for valve servicing, what will already be in place for the 1991 Ford Explorer? Posted by Customer
    A:
    The valves and related components will already be in place.
    Posted by FordPartsGiant Specialist
    Q:
    What other components need to be removed for the 1991 Ford Explorer? Posted by Customer
    A:
    Remove the drive belt, drive belt tensioner, and exhaust manifold(s).
    Posted by FordPartsGiant Specialist
    Q:
    What is the next step after removing the intake manifold for the 1999 Ford Explorer? Posted by Customer
    A:
    Remove the exhaust manifolds. On the left side, remove the bolt and the engine oil dipstick tube.
    Posted by FordPartsGiant Specialist
    Q:
    How should the new gaskets be positioned for the 1991 Ford Explorer? Posted by Customer
    A:
    Position the new gaskets over the dowel pins on the block. Do not use sealant on the gaskets. Be sure the FRONT TOP marks are positioned correctly.
    Posted by FordPartsGiant Specialist
    Q:
    Where can new and rebuilt cylinder heads be commonly found for the 1998 Ford Explorer? Posted by Customer
    A:
    New and rebuilt cylinder heads are commonly available for most engines at dealerships and auto parts stores.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Cylinder Head
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part F87Z-6049-BARM, the Right Choice

To ensure reliability, purchase Ford part # F87Z-6049-BARM Cylinder Head Assembly. It is sometimes referred to as Ford Cylinder Head. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Ford Aerostar, Explorer, Ranger models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford F87Z6049BARM Cylinder Head Assembly. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Ford parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly