Ford E4FZ-6731-AB Filter Assembly - Oil

You can Select Your Vehicle to check if E4FZ-6731-AB fits your vehicle.

Frequent oil changes are important preventive maintenance procedures that can be done by the home mechanic. As engine oil ages, it becomes diluted and contaminated, leading to premature engine wear. Before starting the procedure, make sure you have all the necessary tools, including a drain pan, rubber gloves, breaker bar, socket, and filter wrench. It is also helpful to have rags or newspapers nearby for cleaning up spills. Access to the oil drain plug and filter will be improved if the vehicle can be lifted on a hoist, driven onto ramps, or supported by jackstands. If you haven't changed the oil on this vehicle before, locate the oil drain plug(s) and the oil filter. Be cautious of the hot exhaust components when working under the vehicle. Start the engine and let it reach normal operating temperature before parking on a level surface and shutting off the engine. Raise the vehicle and support it on jack-stands, ensuring it is safely supported. Position a drain pan under the plug in the bottom of the engine and remove the plug using a proper size box end wrench or socket. Some models may have two drain plugs. Inspect the old oil for metal particles. After all the oil has drained, wipe off the drain plug and clean the area around the drain plug opening. Reinstall and tighten the plug securely. Move the drain pan under the oil filter and loosen the filter using a filter wrench. If the filter is too tight, puncture it with a metal bar or long screwdriver to loosen it. Unscrew the filter from the block, being careful to prevent oil from spilling out. Wipe off the mounting surface on the block and ensure no old gasket remains stuck. Smear some engine oil on the rubber gasket of the new filter and screw it into place. Remove all tools and materials from under the vehicle and lower it. Add new oil to the engine through the oil filler cap, pouring four quarts of fresh oil. Wait for the oil to drain into the pan and check the level on the dipstick. Start the engine and check for leaks at the oil pan drain plug and around the oil filter. Tighten if necessary. Wait a few minutes and recheck the oil level. During the first few trips after an oil change, check for leaks and proper oil level. Dispose of the old oil at an oil reclamation center, auto repair shop, or gas station.

Frequent oil changes are important preventive maintenance procedures that can be done by the home mechanic. As engine oil ages, it becomes diluted and contaminated, leading to premature engine wear. Before starting the procedure, make sure you have all the necessary tools, including a drain pan, rubber gloves, breaker bar, socket, and filter wrench. It is also helpful to have rags or newspapers nearby for cleaning up spills. Access to the oil drain plug and filter will be improved if the vehicle can be lifted on a hoist, driven onto ramps, or supported by jackstands. If you haven't changed the oil on this vehicle before, locate the oil drain plug(s) and the oil filter. Be cautious of the hot exhaust components when working under the vehicle. Start the engine and let it reach normal operating temperature before parking on a level surface and shutting off the engine. Raise the vehicle and support it on jack-stands, ensuring it is safely supported. Position a drain pan under the plug in the bottom of the engine and remove the plug using a proper size box end wrench or socket. Some models may have two drain plugs. Inspect the old oil for metal particles. After all the oil has drained, wipe off the drain plug and clean the area around the drain plug opening. Reinstall and tighten the plug securely. Move the drain pan under the oil filter and loosen the filter using a filter wrench. If the filter is too tight, puncture it with a metal bar or long screwdriver to loosen it. Unscrew the filter from the block, being careful to prevent oil from spilling out. Wipe off the mounting surface on the block and ensure no old gasket remains stuck. Smear some engine oil on the rubber gasket of the new filter and screw it into place. Remove all tools and materials from under the vehicle and lower it. Add new oil to the engine through the oil filler cap, pouring four quarts of fresh oil. Wait for the oil to drain into the pan and check the level on the dipstick. Start the engine and check for leaks at the oil pan drain plug and around the oil filter. Tighten if necessary. Wait a few minutes and recheck the oil level. During the first few trips after an oil change, check for leaks and proper oil level. Dispose of the old oil at an oil reclamation center, auto repair shop, or gas station.

Preventive maintenance and prevention of premature engine wear require regular oil changes. Make sure you have the necessary tools and rags for spillage before starting. Raise the vehicle and allow the engine to warm up. Park on a level surface, remove the oil filler cap and drain the oil. Look out for metal particles, reinstall plug(s), and remove the old filter. Clean the mounting surface, apply oil to the new filter, and screw in place. Drop the vehicle, add fresh oil, and check for the level. Start the engine; look for leaks and recheck the oil level. Take old oil to a reclamation center for proper disposal.

One should always change oil regularly to avoid premature wear of engines. Be sure you have the necessary tools at hand and old rags. Lift the car higher up. Start the engine, let it warm up, and park on a plane surface. Jack stands should be used to raise the vehicle, drain pan placed under the oil drain plug. Remove plug, allow all oil to drain out then inspect for metal particles. Reinstall the plug securely. Slide the drip pan under the oil filter and loosen it enough to get it off. Clean the mounting surface, compare old and new filters, lube the new filter gasket, and screw it on by hand.

Frequent oil changes are important preventive maintenance procedures that can be done by the home mechanic. As engine oil ages, it becomes diluted and contaminated, leading to premature engine wear. Before starting the procedure, make sure you have all the necessary tools, including a drain pan, rubber gloves, breaker bar, socket, and filter wrench. It is also helpful to have rags or newspapers nearby for cleaning up spills. Access to the oil drain plug and filter will be improved if the vehicle can be lifted on a hoist, driven onto ramps, or supported by jackstands. If you haven't changed the oil on this vehicle before, locate the oil drain plug(s) and the oil filter. Be cautious of the hot exhaust components when working under the vehicle. Start the engine and let it reach normal operating temperature before parking on a level surface and shutting off the engine. Raise the vehicle and support it on jack-stands, ensuring it is safely supported. Position a drain pan under the plug in the bottom of the engine and remove the plug using a proper size box end wrench or socket. Some models may have two drain plugs. Inspect the old oil for metal particles. After all the oil has drained, wipe off the drain plug and clean the area around the drain plug opening. Reinstall and tighten the plug securely. Move the drain pan under the oil filter and loosen the filter using a filter wrench. If the filter is too tight, puncture it with a metal bar or long screwdriver to loosen it. Unscrew the filter from the block, being careful to prevent oil from spilling out. Wipe off the mounting surface on the block and ensure no old gasket remains stuck. Smear some engine oil on the rubber gasket of the new filter and screw it into place. Remove all tools and materials from under the vehicle and lower it. Add new oil to the engine through the oil filler cap, pouring four quarts of fresh oil. Wait for the oil to drain into the pan and check the level on the dipstick. Start the engine and check for leaks at the oil pan drain plug and around the oil filter. Tighten if necessary. Wait a few minutes and recheck the oil level. During the first few trips after an oil change, check for leaks and proper oil level. Dispose of the old oil at an oil reclamation center, auto repair shop, or gas station.

To prevent engine wear, it is important to change the oil often. Get all the tools and supplies you need. Lift the vehicle and find the drain plug and oil filter. Start the engine, let it warm up, and park on a level surface. Remove the oil filler cap and drain plug while being careful of hot parts. Check if there are any metallic particles on the old oil. Reinstall it securely once you clean it well enough. Clean the mounting surface before installing the new filter and remove the old one after loosening to clean its mounting surface too. Lower the vehicle and add new oil. Check for leaks by inspecting the level first. Make sure that old oil is disposed of properly. No matter how much time passes by some things just stay important.

Add new oil through the filler cap using a funnel to prevent spills. After adding oil, run the engine for about a minute to check for leaks around the drain plug and oil filter. Recheck the oil level and adjust if necessary.

You should have the following tools and materials ready: Drain pan Rubber gloves Breaker bar Socket Filter wrench Rags or newspapers for managing oil spills,etc.

Move the drain pan into position under the oil filter.

After starting the engine for a minute, inspect for leaks at the drain plug and oil filter, and tighten if necessary.

The necessary tools include a drain pan, rubber gloves, breaker bar, socket, and filter wrench. Additionally, having plenty of rags or newspapers on hand for oil spills is advisable.

To install the new oil filter, you should lubricate the gasket with engine oil, hand-tighten it, and then lower the vehicle.

Position a drain pan under the oil drain plug and remove the plug with the correct-sized wrench, wearing a rubber glove to avoid burns. Shift the pan as oil flow slows, inspect the old oil for metal particles, clean the drain plug and surrounding area, reinstall the plug, and move the drain pan under the oil filter.

After removing the oil drain plug, you should inspect the plug for metal particles, wipe it clean, and reinstall it securely.

To reset the oil life monitor, follow the provided steps, which may involve pressing buttons and monitoring the instrument cluster for reset confirmation. The process may vary depending on the model year and vehicle.