×
Contact Us Live Chat or 1-888-788-9341
My Garage
My Account
Cart
Search Bar
Search by Part Number, Part Name, or Vehicle
Track Order Help Center
Make sure this part fits

Ford F3TZ-6V049-DRM Kit - Remanufactured Cylinder Head

1990-1994 Ford F3TZ6V049DRM

Customer Questions & Expert Answers (14)
Ford F3TZ-6V049-DRM Kit - Remanufactured Cylinder Head
Ford F3TZ-6V049-DRM Kit - Remanufactured Cylinder Head
  • Part Description
    Kit - Remanufactured Cylinder Head
  • Base No.
    6V049
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers

  • Related Parts

    Shop for related parts for your vehicle

  • Product Specifications

    BrandGenuine Ford
    Base No.6V049
    Manufacturer Part NumberF3TZ-6V049-DRM, F3TZ6V049DRM
    Part DescriptionKit - Remanufactured Cylinder Head
    Other NamesCylinder Head
    Manufacturer NoteOHV
    Item Dimensions6.6 x 7.7 x 19.4 inches
    ConditionNew
    Fitment TypeDirect Replacement
    Require Quantity2
    ManufacturerFord
    SKUF3TZ-6V049-DRM
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65

  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1990-1994 Ford Aerostar6 Cyl 4.0L4AT A4LD, 5MT
    1991-1994 Ford Explorer6 Cyl 4.0L4AT A4LD, 5MT
    1990-1994 Ford Ranger6 Cyl 4.0L4AT A4LD, 5MT

  • Customer Questions & Expert Answers

    Q:
    Is the the correct part for the attached VIN? Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if F3TZ-6V049-DRM fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    How should the remaining parts be installed for the 1999 Ford Ranger? Posted by Customer
    A:
    Installation of the remaining parts is the reverse of removal.
    Posted by FordPartsGiant Specialist
    Q:
    What should be applied to the cylinder block before installing the head gasket for the 1995 Ford Ranger? Posted by Customer
    A:
    Apply a small amount of suitable silicone sealant to two areas of the cylinder block.
    Posted by FordPartsGiant Specialist
    Q:
    What steps should be taken to install each valve if the head was not sent out for valve servicing for the 2003 Ford Ranger? Posted by Customer
    A:
    1. Lubricate and install each valve. 2. Install new seals on each of the valve stems, ensuring not to twist or cock the seals during installation.
    Posted by FordPartsGiant Specialist
    Q:
    What are the final steps for completing the installation for the 2007 Ford Ranger? Posted by Customer
    A:
    40. Install the rocker arms and hydraulic valve lash adjusters. 41. The remaining installation steps are the reverse of removal. 42. Change the engine oil and filter, then start the engine and check carefully for oil and coolant leaks.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after positioning the new gaskets for the 2008 Ford Ranger? Posted by Customer
    A:
    Install the heads and new head bolts. Tighten the bolts to the torque.
    Posted by FordPartsGiant Specialist
    Q:
    What should be confirmed before loosening the timing belt tensioner for the 2009 Ford Ranger? Posted by Customer
    A:
    Confirm that all camshaft and crankshaft marks are still aligned.
    Posted by FordPartsGiant Specialist
    Q:
    How should threaded holes be cleaned for the 2004 Ford Ranger? Posted by Customer
    A:
    Run an appropriate size tap into each of the threaded holes to remove corrosion and thread sealant that may be present. If compressed air is available, use it to clear the holes of debris produced by this operation.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done if the installed valve spring height is greater than specified for the 1994 Ford Explorer? Posted by Customer
    A:
    A shim can be added under the spring to correct it, but do not shim the springs to the point where the installed height is less than specified.
    Posted by FordPartsGiant Specialist
    Q:
    How should the push rod ends be inspected for the 1996 Ford Explorer? Posted by Customer
    A:
    Inspect the push rod ends for scuffing and excessive wear. Roll each push rod on a flat surface, like a piece of plate glass, to determine if it's bent.
    Posted by FordPartsGiant Specialist
    Q:
    How should the cylinder head bolts be installed and tightened for the 1995 Ford Explorer? Posted by Customer
    A:
    Install the bolts finger tight, then follow the recommended sequence and tighten the bolts in steps to the specified torque.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after installing the cylinder heads and bolts for the 1998 Ford Explorer? Posted by Customer
    A:
    Referring to Section 7, apply the sealer and position the intake manifold on the engine. Install the intake manifold bolts/nuts and tighten them hand-tight.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done once all the valves and related components have been removed and stored for the 1997 Ford Explorer? Posted by Customer
    A:
    The head should be thoroughly cleaned and inspected. If a complete engine overhaul is being done, finish the engine disassembly procedures before beginning the cylinder head cleaning and inspection process.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Cylinder Head
    Q:
    What should be done with the accessory bracket for the 1996 Ford Explorer? Posted by Customer
    A:
    Remove the bolts on the accessory bracket and set the bracket aside.
    Posted by FordPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part F3TZ-6V049-DRM, the Right Choice

To ensure reliability, purchase Ford part # F3TZ-6V049-DRM Kit - Remanufactured Cylinder Head. It is sometimes referred to as Ford Cylinder Head. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Ford Aerostar, Explorer, Ranger models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford F3TZ6V049DRM Kit - Remanufactured Cylinder Head. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Ford parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly