Ford 1L8Z-7515-AA Lever Assembly - Clutch Release

You can Select Your Vehicle to check if 1L8Z-7515-AA fits your vehicle.

To delete the clutch release bearing but on 2013 and later models, the clutch release bearing is belong to the clutch release cylinder and cannot be separated therefore both have to be replaced, transaxle has to be removed firstly. Next, remove the clutch fork from the ballstud and withdraw the release bearing from the input shaft together with the help of the clutch fork. For examination, remove grease and dirt on the bearing using a piece of cloth; do not immerse it in any solvent because it is hermetically sealed for use. Swing the outer part of the bearing while applying force to center of it; if the bearing appears to be stiff or if it is producing unpleasant noises, it must be replaced. Since it is almost impossible to replace the release bearing, it is recommended that it should be changed every time the clutch parts are changed. For installation light coat of high temperature grease should be applied to the friction surface of release bearing, ballstud and input shaft bearing retainer and then simply reverse the steps of the removal procedures and install the clutch fork and bearing to the input shaft.

Dust produced by clutch wear is hazardous to your health. Do not blow it out with compressed air or inhale it. Avoid using gasoline or petroleum-based solvents to remove the dust. Use brake system cleaner to flush the dust into a drain pan. After the clutch components are wiped clean with a rag, dispose of the contaminated rags and cleaner in a covered, marked container.To remove the clutch, access to its components is normally achieved by removing the transaxle, leaving the engine in the vehicle. Check the clutch for wear and replace worn components as necessary when the engine is being removed for major overhaul. However, the relatively low cost of the clutch components compared to the time and trouble spent gaining access to them warrants their replacement anytime the engine or transaxle is removed, unless they are new or in near perfect condition. Remove the transaxle from the vehicle. Support the engine while the transaxle is out, preferably using an engine support fixture or a hoist from above. The clutch fork and release bearing can remain attached to the transaxle housing for the time being. To support the clutch disc during removal, install a clutch alignment tool through the clutch disc hub.Carefully inspect the flywheel and pressure plate for indexing marks. If they cannot be found, scribe or paint marks yourself so the pressure plate and the flywheel will be in the same alignment during installation. Loosen the pressure plate-to-flywheel bolts in a criss-cross pattern until all spring pressure is relieved. Then, hold the pressure plate securely and completely remove the bolts, followed by the pressure plate and clutch disc.When inspecting clutch components, look for problems such as wear on the clutch disc. Inspect the flywheel for cracks, heat checking, grooves and other obvious defects. A machine shop can smoothen slight imperfections. Inspect the clutch disc lining and replace it if in doubt about its condition. The release bearing should also be replaced along with the clutch disc.Check the machined surfaces and the diaphragm spring fingers of the pressure plate. If damaged, replace the pressure plate. Check the pilot bearing in the end of the crankshaft for excessive wear and replace it if necessary. To remove the pilot bearing, use a slide hammer and puller attachment.To install a new pilot bearing, lightly lubricate the outside surface with grease, then drive it into the recess with a bearing driver or a socket. Clean the flywheel and pressure plate machined surfaces with brake cleaner, lacquer thinner, or acetone before installation. No oil or grease should be on these surfaces or the lining of the clutch disc.Position the clutch disc and pressure plate against the flywheel with the clutch held in place with an alignment tool. Ensure the disc is installed properly. Tighten the pressure plate-to-flywheel bolts only finger tight, working around the pressure plate. Center the clutch disc by ensuring the alignment tool extends through the splined hub and into the pilot bearing in the crankshaft. Tighten the bolts in a criss-cross pattern to prevent distorting the cover and remove the alignment tool.Lubricate the inner groove of the release bearing with high-temperature grease. Also, place a small amount of grease on the release lever contact areas and the transaxle input shaft bearing retainer. Install the clutch release bearing. Install the transaxle and all components removed previously.

Dust produced by clutch wear is hazardous to your health. DO NOT blow it out with compressed air and DO NOT inhale it. DO NOT use gasoline or petroleum-based solvents to remove the dust. Brake system cleaner should be used to flush the dust into a drain pan. After the clutch components are wiped clean with a rag, dispose of the contaminated rags and cleaner in a covered, marked container. REMOVAL: Remove the transaxle. Pull the clutch fork off the ballstud and slide the release bearing off the input shaft along with the clutch fork. INSPECTION: Wipe off the bearing with a clean rag and inspect it for damage, wear, and cracks. Hold the center of the bearing and rotate the outer portion while applying pressure. If the bearing doesn't turn smoothly or if it's noisy or rough, replace it. INSTALLATION: Lightly lubricate the friction surfaces of the release bearing, ballstud, and the input shaft bearing retainer with high-temperature grease. Install the clutch fork and bearing onto the input shaft. The remainder of installation is the reverse of removal.