Lincoln 6W1Z-2N712-A Kit - Brake Shoe And Lining

You can Select Your Vehicle to check if 6W1Z-2N712-A fits your vehicle.

Loosen the wheel lug nuts, raise the rear of the vehicle and support it securely on jackstands. Block the front wheels to keep the vehicle from rolling. Release the parking brake. Remove the wheel. All four rear brake shoes must be replaced at the same time, but to avoid mixing up parts, work on only one brake assembly at a time. Follow the accompanying photos for the inspection and replacement of the brake shoes. Be sure to stay in order and read the caption under each illustration. If the brake drum cannot be easily pulled off, pry the rubber plug from the backing plate inspection hole and insert a screwdriver and a brake adjusting tool to lift the adjusting lever and rotate the adjusting screw. This will cause the brake shoes to pull together. Spray the assembly with penetrating oil and allow the oil to soak in if the mechanism is difficult to turn. The drum should now come off. Before reinstalling the drum it should be checked for cracks, score marks, deep scratches and hard spots, which will appear as small discolored areas. If the hard spots cannot be removed with fine emery cloth or if any of the other conditions listed above exist, the drum must be taken to an automotive machine shop to have it turned. Professionals recommend resurfacing the drums whenever a brake job is done. Resurfacing will eliminate the possibility of out-of-round drums. If the drums are worn so much that they can't be resurfaced without exceeding the maximum allowable diameter, which is stamped into the drum, then new ones will be required. At the very least, if you elect not to have the drums resurfaced, remove the glazing from the surface with medium-grit emery cloth using a swirling motion. Install the brake drum on the hub. Mount the wheel, install the lug nuts, then lower the vehicle. Make a number of forward and reverse stops to adjust the brakes until satisfactory pedal action is obtained.

Loosen the rear wheel lug nuts. Raise the rear of the vehicle and place it securely on jackstands. Remove the rear wheels. Remove the caliper and the brake disc. It's not necessary to disconnect the brake hose from the caliper; but hang the caliper out of the way with a piece of wire to prevent damage to the hose. Remove the axleshafts. Inspect the thickness of the lining material on the shoes. If the lining has worn down to 0.040 inch or less, the shoes must be replaced. Disconnect the rear parking brake cable from the parking brake lever. Follow the accompanying photos for the parking brake shoe replacement procedure. Be sure to stay in order and read the caption under each illustration. Install the axleshaft and the brake disc. Temporarily thread three of the wheel lug nuts onto the studs to hold the disc in place. Remove the rubber access plug from the backside of the brake torque plate. Adjust the parking brake shoe clearance by turning the adjuster star wheel with a brake adjusting tool or screwdriver until the shoes contact the disc and the disc can't be turned. Back-off the adjuster eight notches, then install the hole plug. Install the brake caliper. Be sure to tighten the bolts. Install the wheel and tighten the lug nuts. To bed the shoes to the drum, drive the vehicle at approximately 30 mph on a dry, level road. Depress the parking brake pedal with about 20 pounds of force. Note: The vacuum release mechanism will prevent the parking brake from setting, if it is operating properly. Be sure to check the function of the vacuum release before performing the bedding-in procedure. Drive the vehicle for 1/4-mile with the parking brake applied like this. Repeat this procedure two or three times, allowing the brakes to cool between applications.

Loosen the rear wheel lug nuts. Raise the rear of the vehicle and place it securely on jackstands. Remove the rear wheels. Remove the caliper and the brake disc. It's not necessary to disconnect the brake hose from the caliper; but hang the caliper out of the way with a piece of wire to prevent damage to the hose. Remove the axleshafts. Inspect the thickness of the lining material on the shoes. If the lining has worn down to 0.040 inch or less, the shoes must be replaced. Disconnect the rear parking brake cable from the parking brake lever. Follow the accompanying photos for the parking brake shoe replacement procedure. Be sure to stay in order and read the caption under each illustration. Install the axleshaft and the brake disc. Temporarily thread three of the wheel lug nuts onto the studs to hold the disc in place. Remove the rubber access plug from the backside of the brake torque plate. Adjust the parking brake shoe clearance by turning the adjuster star wheel with a brake adjusting tool or screwdriver until the shoes contact the disc and the disc can't be turned. Back-off the adjuster eight notches, then install the hole plug. Install the brake caliper. Be sure to tighten the bolts. Install the wheel and tighten the lug nuts. To bed the shoes to the drum, drive the vehicle at approximately 30 mph on a dry, level road. Depress the parking brake pedal with about 20 pounds of force. Note: The vacuum release mechanism will prevent the parking brake from setting, if it is operating properly. Be sure to check the function of the vacuum release before performing the bedding-in procedure. Drive the vehicle for 1/4-mile with the parking brake applied like this. Repeat this procedure two or three times, allowing the brakes to cool between applications.

Loosen the wheel lug nuts, raise the rear of the vehicle and support it securely on jackstands. Block the front wheels to keep the vehicle from rolling. Release the parking brake. Remove the wheel. All four rear brake shoes must be replaced at the same time, but to avoid mixing up parts, work on only one brake assembly at a time. Follow the accompanying photos for the inspection and replacement of the brake shoes. Be sure to stay in order and read the caption under each illustration. If the brake drum cannot be easily pulled off, pry the rubber plug from the backing plate inspection hole and insert a screwdriver and a brake adjusting tool to lift the adjusting lever and rotate the adjusting screw. This will cause the brake shoes to pull together. Spray the assembly with penetrating oil and allow the oil to soak in if the mechanism is difficult to turn. The drum should now come off. Before reinstalling the drum it should be checked for cracks, score marks, deep scratches and hard spots, which will appear as small discolored areas. If the hard spots cannot be removed with fine emery cloth or if any of the other conditions listed above exist, the drum must be taken to an automotive machine shop to have it turned. Professionals recommend resurfacing the drums whenever a brake job is done. Resurfacing will eliminate the possibility of out-of-round drums. If the drums are worn so much that they can't be resurfaced without exceeding the maximum allowable diameter, which is stamped into the drum, then new ones will be required. At the very least, if you elect not to have the drums resurfaced, remove the glazing from the surface with medium-grit emery cloth using a swirling motion. Install the brake drum on the hub. Mount the wheel, install the lug nuts, then lower the vehicle. Make a number of forward and reverse stops to adjust the brakes until satisfactory pedal action is obtained.

Make a number of forward and reverse stops to adjust the brakes until satisfactory pedal action is obtained.

1. Install the parking brake actuator lever on the new brake shoe and secure it with the retaining clip. 2. Lubricate the adjusting screw assembly and shoe guide pads with high-temperature brake grease. 3. Position the shoes on the backing plate, insert retaining pins, and install the springs and retaining spring caps. 4. Install the adjusting screw, adjusting pawl, anchor pin plate, cable guide, and cable. 5. Connect the cable and spring to the adjuster lever and install the drum.

Remove the rubber dust plug on the back of the anchor plate and use a brake tool to back off the shoe adjuster mechanism until the disc can be removed.

Remove the rear disc brake pads.