Lincoln 7C3Z-1521990-A Lock Cylinder Less Keys

You can Select Your Vehicle to check if 7C3Z-1521990-A fits your vehicle.

To address the door latch, first raise the window and remove the door trim panel along with the watershield. Next, take out the screws that secure the latch to the door, detach the locking rods and cable, and pull the latch assembly through the access hole. While working through the large access hole, position the latch to disengage the outside door handle and lock cylinder from the latch rods, as well as the inside handle from the latch cable. All door locking rods are attached by plastic clips, which can be removed by unsnapping the portion engaging the connecting rod and pulling the rod out of its locating hole. Adjust the latch to disengage the door lock actuator hook, then remove the latch assembly from the door, with installation being the reverse of removal. For the outside handle and door lock cylinder assembly, raise the window and remove the door trim panel and watershield. Through the large access hole, disengage the plastic clips securing the lock cylinder to the latch rod and the door handle to the latch rod. Disconnect any electrical connectors that may interfere with removal, then remove the outside handle retaining nuts accessible through the access hole in the door frame and pull the handle and lock cylinder assembly from the door, with installation being the reverse of removal. For the inside handle and cable, remove the door trim panel and peel away the watershield. Take out the bolt securing the inside handle and pull rearward to disengage it from the inner door panel. Detach the latch rod from the backside of the handle and remove it from the vehicle, rotating the handle out and detaching the latch rod retaining clip, with installation being the reverse of removal.

To address the door latch, first raise the window and remove the door trim panel along with the watershield. Next, take out the screws that secure the latch to the door, detach the locking rods and cable, and pull the latch assembly through the access hole. While working through the large access hole, position the latch to disengage the outside door handle and lock cylinder from the latch rods, as well as the inside handle from the latch cable. All door locking rods are attached by plastic clips, which can be removed by unsnapping the portion engaging the connecting rod and pulling the rod out of its locating hole. Adjust the latch to disengage the door lock actuator hook, then remove the latch assembly from the door, with installation being the reverse of removal. For the outside handle and door lock cylinder assembly, raise the window and remove the door trim panel and watershield. Through the large access hole, disengage the plastic clips securing the lock cylinder to the latch rod and the door handle to the latch rod. Disconnect any electrical connectors that may interfere with removal, then remove the outside handle retaining nuts accessible through the access hole in the door frame and pull the handle and lock cylinder assembly from the door, with installation being the reverse of removal. For the inside handle and cable, remove the door trim panel and peel away the watershield. Take out the bolt securing the inside handle and pull rearward to disengage it from the inner door panel. Detach the latch rod from the backside of the handle and remove it from the vehicle, rotating the handle out and detaching the latch rod retaining clip, with installation being the reverse of removal.

For the remedy of the door latch, raise and remove the door trim panel along with the watershield and the window together. Lastly, unscrew the nuts that hold the latch in position on the door particular the retaining screws that are usually at the far end of the door. Pull the latch to align it with the large access hole, and while doing this exercise release the electrical connectors as may be necessary followed by the outer door handle and the rod that interconnects the outer lock cylinder with the latch and finally pull out the latch assembly from the door. For the outside handle and door lock cylinder assembly, first, raise the window and pull the door trim panel as well as the watershield. Remove the actuating rods for the door handle and the lock cylinder through the access hole and the mounting fasteners for the door handle. Remove any electrical connectors which might hamper the process and unscrew the rest to detach the door handle/lock cylinder and door including the removal of the rubber inserts to get to the rest of the fasteners. Reinstallation also deploys the process in the order that is opposite to the removal one.

This lock cylinder comes with all parts necessary to install