Make sure this part fits

Mercury 6E5Z-17618-A Reservoir - Water

2006-2011 Mercury Milan 6E5Z17618A

Customer Questions & Expert Answers (2)
Ford 6E5Z-17618-A Reservoir - Water
  • Part Description
    Reservoir - Water
  • Base No.
    17618
  • Replaces
    6E5Z-17618-AA
  • Manufacturer
    Ford
Make sure this part fits
$51.41 MSRP: $82.00
You Save: $30.59 (38%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Mercury
    Base No.17618
    Manufacturer Part Number6E5Z-17618-A, 6E5Z17618A
    Part DescriptionReservoir - Water
    Other NamesReservoir Assembly, Washer Pump
    Manufacturer NoteIncludes Pump
    Item Dimensions18.7 x 12.4 x 9.3 inches
    Item Weight4.10 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces6E5Z-17618-AA
    ManufacturerFord
    SKU6E5Z-17618-A
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2006-2011 Mercury Milan4 Cyl 2.3L, 4 Cyl 2.5L Duratec HE PFI, 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L DOHC EFI, 6 Cyl 3.0L OHC Duratec, 6 Cyl 3.5L DOHC VCT SMPI5-Speed Automatic Transmission Mazda FNR5, 5-Speed Manual Transmission (G5M), 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Manual Transmission Mazda G6M, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
  • Customer Questions & Expert Answers

    Q:
    Can you tell me if this part is correct for my car? Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 6E5Z-17618-A fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    How to remove and install wiper motors,windshield washer reservoir and washer pump on Ford Fusion? Posted by Customer
    A:
    In order to remove the wiper motor if 2012 and earlier models, one has to take off the wiper arm nuts and place a mark on the wiper arm shaft then removes the both wiper arms. Next, remove the hand that is black and plastic on the cowl and then you unplug the electrical connection of the wiper motor. The wiper motor and link assembly require the use of a trim removal tool or a flat head screwdriver to have the two mounting bolts removed from the link to crank arm joint, thus separating the linkage. Lose the bolt connecting the crank arm and the motor shaft, place a scratchmark on the crank arm, in relation to the motor shaft, and finally, you set the crank arm aside. Take out the two motor mounting bolts and pull the motor out from its mounting bracket, how to install is as follows but in reverse. For the models manufactured since 2013, the vehicles have L & R wiper motors, and the procedure starts with the removal of the wiper arms and the cowl panel trim, the separation of the electrical connection of the wiper motor, and the removal of the bolts that hold the motor to the vehicle, and then the extraction of the wiper motor from the vehicle; while the installation process is done in reverse with the tightening of the As for the WSR and WP, the right-front wheel lug nuts should be loosened and the front of the vehicle should be raised on jackstands; the wheel should then be removed, as well as the inner fender splash shield. In order to open it, if required remove the bolts has been holding the outer edge of the bumper to the fender and remove the under vehicle close out covers. Locate the washer pump wires or hoses and relax the connectors from the pump to the wires and set a drain pan underneath the reservoir to catch the washer fluid. Disconnect the hoses connected to the washer pump, keep a mark of which ones go where so they can be reattached. The washer pump is situated such that the reservoir does not have to be detached if only the pump is to be replaced; if only the pump is to be replaced, proceed as follows: Remove the bolts that holds the washer reservoir to the vehicle and pull the washer reservoir from the bottom. For the washer pump, unplug the grommet and pull out the pump and to replace the washer pump one must fix a new grommet. Removal and installation share similarity with a general definition that installation is the removal in a reverse manner.
    Posted by FordPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part 6E5Z-17618-A, the Right Choice

To ensure reliability, purchase Ford part # 6E5Z-17618-A Reservoir - Water. It is sometimes referred to as Mercury Washer Reservoir. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Mercury Milan models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford 6E5Z17618A Reservoir - Water. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Mercury parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly