Mercury F89Z-4676-AA Seal Assembly - Oil

You can Select Your Vehicle to check if F89Z-4676-AA fits your vehicle.

Raise the rear of the vehicle and place it securely on jackstands, then remove the rear wheels, brake calipers, and brake discs. Mark the driveshaft and companion flange for ease of realignment during reassembly, then remove the driveshaft. Mark the relationship between the pinion and companion flange. Using an inch-pound torque wrench, measure and record the torque required to turn the pinion nut through several revolutions, which will be used when the pinion flange is reinstalled. Hold the companion flange with a suitable tool and remove the pinion nut, then use a small puller if necessary to separate the pinion flange from the pinion shaft. Pry out the old seal with a seal removal tool, clean the oil seal mounting surface, and tap the new seal into place, ensuring it is inserted squarely. Inspect the splines on the pinion shaft for burrs and nicks, removing any rough areas with a crocus cloth and wiping the splines clean. Install the companion flange, aligning it with the marks made during removal, and gently tap it on with a soft-faced hammer until the pinion nut can be started on the pinion shaft. Hold the companion flange while tightening the pinion nut, stopping frequently to take rotational torque measurements until the previously recorded measurement is reached. If the recorded measurement was less than the pinion bearing preload torque, continue tightening until the specified torque is reached; if it was more, continue until the recorded measurement is reached, avoiding backing off the nut to reduce preload. Reinstall the driveshaft, brake discs, brake calipers, and wheels, check the differential oil level and fill as necessary, then lower the vehicle and take a test drive to check for leaks.

Raise the vehicle and support it securely on jack stands, then remove the rear wheels and brake drums. Mark the driveshaft and axle pinion flange for ease of realignment during reassembly, and remove the driveshaft. Install a torque wrench to the pinion nut and record the torque through several revolutions. Mark the relationship between the pinion and flange, hold the flange to keep it from turning, and remove the pinion nut along with the differential flange. Pry out the old seal using a slide hammer or Ford tool T65L-4851-A, then clean the oil seal mounting surface. Tap the new seal into place, ensuring it is inserted squarely. Inspect the splines on the pinion shaft for burrs and nicks, removing any rough areas with a crocus cloth and wiping the splines clean. Install the differential flange, aligning it with the marks made during removal, and tighten the pinion nut while allowing some movement for proper seating. Take frequent pinion bearing preload measurements until the original readings are obtained, then reinstall the driveshaft, brake drums, and wheels. Check the differential oil level and fill as necessary, lower the car, and take a short test drive to check for leaks.

To remove the rear axle cover, raise your vehicle and support using a jack stand. Remove the bolts and nuts holding the rear axle cover to the axle mount. Put in place the bolt for the rear mount into the lower bolt hole allowing pivot forward of the axle. Slide the driveshaft forward and let it rest on the driveshaft hoop. Take off the nuts that keep the carrier on the front mount. Slowly lowering the carrier will give access to the companion flange. Use a pinion nut removal tool or a wrench and socket to get rid of it. Get rid of the companion flange as well. A screwdriver blade should be wedged between the housing and seal, the metal flange lifted using a locking plier then seal pulled out with locking pliers. To install, use an installer drive or pipe slightly smaller than a seal. Look for burrs on mating surfaces, remove them if any with emery cloth, and put back reference marked companion flange over pinion shafts.

Loosen the rear wheel lug nuts, raise the rear of the vehicle and place it securely on jackstands. Remove the rear wheels. Remove the brake drums or calipers. Mark the driveshaft and companion flange for ease of realignment during reassembly, then remove the driveshaft. Mark the relationship between the pinion and companion flange. Using an inch-pound torque wrench, measure and record the torque required to turn the pinion nut through several revolutions (pinion bearing preload). Using a suitable tool, hold the companion flange and remove the pinion nut. Using a suitable puller, remove the companion flange. Pry out the old seal with a slide hammer and reversed jaws or other appropriate tool. Clean the oil seal mounting surface. Tap the new seal into place, taking care to insert it squarely. Inspect the splines on the pinion shaft for burrs and nicks. Remove any rough areas with a crocus cloth. Wipe the splines clean. Install the companion flange, aligning it with the marks made during removal. Gently tap the flange on with a soft-faced hammer until you can start the pinion nut on the pinion shaft. Using a suitable tool, hold the companion flange while tightening the pinion nut to the minimum torque. While tightening, take frequent rotational torque measurements, using the inch-pound torque wrench, until the measurement recorded is reached. Caution: If the measurement was less than the pinion bearing preload torque, continue tightening until the specified preload is reached. If it was more than specified, stop when the specified preload is reached. Under no circumstances should the pinion nut be backed off to reduce pinion bearing preload. Increase the nut torque in small increments and check the preload after each increase. Reinstall the driveshaft, brake drums and wheels. Check the differential oil level and fill as necessary. Lower the vehicle and take a test drive to check for leaks.

Remove half shaft assembly. Use seal puller or prybar to remove seal. Connect slide hammer to puller and remove seal. Lubricate seal and align with housing bore. Use driver or socket, extension, and hammer to install seal. Ensure seal is not cocked, if so, install new one. Install half shaft assembly.

Loosen the rear wheel lug nuts, raise the rear of the vehicle and place it securely on jackstands. Remove the rear wheels. Remove the brake drums or calipers. Mark the driveshaft and companion flange for ease of realignment during reassembly, then remove the driveshaft. Mark the relationship between the pinion and companion flange. Using an inch-pound torque wrench, measure and record the torque required to turn the pinion nut through several revolutions (pinion bearing preload). Using a suitable tool, hold the companion flange and remove the pinion nut. Using a suitable puller, remove the companion flange. Pry out the old seal with a slide hammer and reversed jaws or other appropriate tool. Clean the oil seal mounting surface. Tap the new seal into place, taking care to insert it squarely. Inspect the splines on the pinion shaft for burrs and nicks. Remove any rough areas with a crocus cloth. Wipe the splines clean. Install the companion flange, aligning it with the marks made during removal. Gently tap the flange on with a soft-faced hammer until you can start the pinion nut on the pinion shaft. Using a suitable tool, hold the companion flange while tightening the pinion nut to the minimum torque. While tightening, take frequent rotational torque measurements, using the inch-pound torque wrench, until the measurement recorded is reached. Caution: If the measurement was less than the pinion bearing preload torque, continue tightening until the specified preload is reached. If it was more than specified, stop when the specified preload is reached. Under no circumstances should the pinion nut be backed off to reduce pinion bearing preload. Increase the nut torque in small increments and check the preload after each increase. Reinstall the driveshaft, brake drums and wheels. Check the differential oil level and fill as necessary. Lower the vehicle and take a test drive to check for leaks.

Loosen the rear wheel lug nuts, raise the rear of the vehicle and place it securely on jackstands. Remove the rear wheels. Remove the brake drums or calipers. Mark the driveshaft and companion flange for ease of realignment during reassembly, then remove the driveshaft. Mark the relationship between the pinion and companion flange. Using an inch-pound torque wrench, measure and record the torque required to turn the pinion nut through several revolutions (pinion bearing preload). Using a suitable tool, hold the companion flange and remove the pinion nut. Using a suitable puller, remove the companion flange. Pry out the old seal with a slide hammer and reversed jaws or other appropriate tool. Clean the oil seal mounting surface. Tap the new seal into place, taking care to insert it squarely. Inspect the splines on the pinion shaft for burrs and nicks. Remove any rough areas with a crocus cloth. Wipe the splines clean. Install the companion flange, aligning it with the marks made during removal. Gently tap the flange on with a soft-faced hammer until you can start the pinion nut on the pinion shaft. Using a suitable tool, hold the companion flange while tightening the pinion nut to the minimum torque. While tightening, take frequent rotational torque measurements, using the inch-pound torque wrench, until the measurement recorded is reached. Caution: If the measurement was less than the pinion bearing preload torque, continue tightening until the specified preload is reached. If it was more than specified, stop when the specified preload is reached. Under no circumstances should the pinion nut be backed off to reduce pinion bearing preload. Increase the nut torque in small increments and check the preload after each increase. Reinstall the driveshaft, brake drums and wheels. Check the differential oil level and fill as necessary. Lower the vehicle and take a test drive to check for leaks.

Remove half shaft assembly. Use seal puller or prybar to remove seal. Connect slide hammer to puller and remove seal. Lubricate seal and align with housing bore. Use driver or socket, extension, and hammer to install seal. Ensure seal is not cocked, if so, install new one. Install half shaft assembly.

Raise the vehicle and support it securely on jack stands, then remove the rear wheels and brake drums. Mark the driveshaft and axle pinion flange for ease of realignment during reassembly, and remove the driveshaft. Install a torque wrench to the pinion nut and record the torque through several revolutions. Mark the relationship between the pinion and flange, hold the flange to keep it from turning, and remove the pinion nut along with the differential flange. Pry out the old seal using a slide hammer or Ford tool T65L-4851-A, then clean the oil seal mounting surface. Tap the new seal into place, ensuring it is inserted squarely. Inspect the splines on the pinion shaft for burrs and nicks, removing any rough areas with a crocus cloth and wiping the splines clean. Install the differential flange, aligning it with the marks made during removal, and tighten the pinion nut while allowing some movement for proper seating. Take frequent pinion bearing preload measurements until the original readings are obtained, then reinstall the driveshaft, brake drums, and wheels. Check the differential oil level and fill as necessary, lower the car, and take a short test drive to check for leaks.

To remove the rear axle cover, raise your vehicle and support using a jack stand. Remove the bolts and nuts holding the rear axle cover to the axle mount. Put in place the bolt for the rear mount into the lower bolt hole allowing pivot forward of the axle. Slide the driveshaft forward and let it rest on the driveshaft hoop. Take off the nuts that keep the carrier on the front mount. Slowly lowering the carrier will give access to the companion flange. Use a pinion nut removal tool or a wrench and socket to get rid of it. Get rid of the companion flange as well. A screwdriver blade should be wedged between the housing and seal, the metal flange lifted using a locking plier then seal pulled out with locking pliers. To install, use an installer drive or pipe slightly smaller than a seal. Look for burrs on mating surfaces, remove them if any with emery cloth, and put back reference marked companion flange over pinion shafts.

If the vehicle is equipped with air suspension, turn off the air suspension system. The switch is located in the area of the right kick panel. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it securely on jackstands. Block the front wheels to keep the vehicle from rolling off the stands. Remove the wheels, this will allow you to obtain a more accurate pinion shaft preload reading. Disconnect the driveshaft and fasten it out of the way. Use an inch-pound torque wrench to check the torque required to rotate the pinion. Record it for use later. Put alignment marks on the pinion shaft, nut and flange. Count the number of threads visible between the end of the nut and the end of the pinion shaft and record it for use later. A special tool can be used to keep the companion flange from moving while the self-locking pinion nut is loosened. If the special tool isn't available, insert a screwdriver through one of the bolt holes. Remove the pinion nut. Remove the companion flange. It may be necessary to use a two or three-jaw puller to pull off the flange. Do NOT attempt to pry behind the flange or hammer on the end of the pinion shaft. Pry out the old seal and discard it. Lubricate the lips of the new seal with high-temperature grease and tap it evenly into position with a seal installation tool or a large socket. Make sure it enters the housing squarely and is tapped in to its full depth. Align the mating marks made before disassembly and install the companion flange. If necessary, tighten the pinion nut to draw the flange into place. Do not try to hammer the flange into position. Apply non-hardening sealant to the ends of the splines visible in the center of the flange so oil will be sealed in. Install the washer (if equipped) and pinion nut. Tighten the nut carefully until the original number of threads are exposed. Measure the torque required to rotate the pinion and tighten the nut in small increments until it matches the figure recorded earlier. In order to compensate for the drag of the new oil seal, the nut should be tightened more until the rotational torque of the pinion slightly exceeds what was recorded earlier, but not by more than 5 in-lbs. Connect the driveshaft, install the wheels and lower the vehicle. Tighten the lug nuts.

Clean the oil seal mounting surface thoroughly. Tap the new seal into place, ensuring it is inserted squarely.

Install the companion flange, aligning it with the marks made during removal. Gently tap the flange on with a soft-faced hammer until you can start the pinion nut on the pinion shaft.

Reinstall all components removed previously by reversing the removal process, tightening all fasteners to their specified torque values.