Mercury XW7Z-18808-CA Speaker Assembly

You can Select Your Vehicle to check if XW7Z-18808-CA fits your vehicle.

Disconnect the negative battery cable, then the positive battery cable, and wait two minutes before proceeding. Remove the radio trim bezel from the center of the instrument panel. For 2002 and earlier models, the radio receiver is retained in the instrument panel by special clips, which can be released using two sets of removal tools or two short lengths of coat hanger wire bent into U-shapes. Insert the tools into the holes at the corners of the radio assembly until the internal clips release, then push outward simultaneously on both tools while pulling the assembly out of the instrument panel. Disconnect the antenna and electrical connectors to remove the unit from the vehicle. To install the radio, plug in the electrical connectors, slide the radio along the track into the instrument panel, and ensure the clips snap into place. For 2003 and later models, remove the screws securing the radio, slide the radio assembly out far enough to disengage any electrical connectors, and then slide the radio all the way out, with installation being the reverse of removal. To access the speakers, remove the door trim panel, then take out the mounting screws, withdraw the speaker, unplug the electrical connector, and remove the speaker from the vehicle. Installation is the reverse of removal.

Disconnect the negative battery cable, then the positive battery cable, and wait two minutes before proceeding. Remove the radio trim bezel from the center of the instrument panel. For 2002 and earlier models, the radio receiver is retained in the instrument panel by special clips, which can be released using two sets of removal tools or two short lengths of coat hanger wire bent into U-shapes. Insert the tools into the holes at the corners of the radio assembly until the internal clips release, then push outward simultaneously on both tools while pulling the assembly out of the instrument panel. Disconnect the antenna and electrical connectors to remove the unit from the vehicle. To install the radio, plug in the electrical connectors, slide the radio along the track into the instrument panel, and ensure the clips snap into place. For 2003 and later models, remove the screws securing the radio, slide the radio assembly out far enough to disengage any electrical connectors, and then slide the radio all the way out, with installation being the reverse of removal. To access the speakers, remove the door trim panel, then take out the mounting screws, withdraw the speaker, unplug the electrical connector, and remove the speaker from the vehicle. Installation is the reverse of removal.

Disconnect the cable from the negative battery terminal. For earlier models of the radio/CD player, remove the screws and detach the bezel. Then, remove the mounting screws. Slide the radio/CD unit out and support it, disconnect the ground cable, antenna and electrical connectors, then remove the assembly from the instrument panel. Installation is the reverse of removal. For later models, the radio receiver and CD player assemblies are retained in the instrument panel by special clips. Releasing these clips requires the use of two sets of special removal tools, available at most auto parts stores, or two short lengths of coathanger wire bent into U-shapes. With the clips released, flex out simultaneously on both tools and pull the assembly out of the instrument panel, disconnect the antenna and electrical connectors and remove the unit from the vehicle. Install by connecting the electrical connectors, then sliding the radio or CD player along the track and into the instrument panel until the clips can be felt snapping in place. For door mounted speakers, remove the door trim panel. Remove the mounting screws, withdraw the speaker, disconnect the electrical connector and remove the speaker from the vehicle. Installation is the reverse of removal. For rear quarter panel mounted speakers, remove the screws and pry off the speaker grille. Remove the retaining screws, withdraw the speaker, disconnect the electrical connector and remove the speaker from the vehicle. Installation is the reverse of removal. For package shelf mounted speakers, open the trunk lid. Working under the package tray, disconnect electrical connector, remove the retaining screws/nuts or detach the clips, then lower the speaker and remove it from the vehicle. Installation is the reverse of removal.

Disconnect the cable from the negative battery terminal. For 1991 and earlier models, remove the screws and detach the bezel, then take out the mounting screws. Slide the radio/CD unit out, support it, disconnect the ground cable, antenna, and electrical connectors, and remove the assembly from the instrument panel, with installation being the reverse of removal. For 1992 and later models, the radio receiver and CD player assemblies are secured by special clips that require radio removal tools or U-shaped coathanger wire to release. Insert the tools into the holes at the corners of the assembly until the internal clips release, then flex out on both tools while pulling the assembly out, disconnecting the antenna and electrical connectors before removing the unit from the vehicle. To install, plug in the electrical connectors, slide the radio or CD player into the instrument panel until the clips snap in place. For door-mounted speakers, remove the door trim panel, take out the mounting screws, withdraw the speaker, unplug the electrical connector, and remove the speaker from the vehicle, with installation being the reverse of removal. For rear quarter panel mounted speakers, remove the screws and pry off the speaker grille, then take out the retaining screws, withdraw the speaker, unplug the electrical connector, and remove the speaker from the vehicle, with installation being the reverse of removal. For package shelf mounted speakers, open the trunk lid, work under the package tray to unplug the electrical connector, remove the retaining screws/nuts or detach the clips, then lower the speaker and remove it from the vehicle, with installation being the reverse of removal.

Disconnect the cable from the negative battery terminal. For 1991 and earlier models, remove the screws and detach the bezel, then take out the mounting screws. Slide the radio/CD unit out, support it, disconnect the ground cable, antenna, and electrical connectors, and remove the assembly from the instrument panel, with installation being the reverse of removal. For 1992 and later models, the radio receiver and CD player assemblies are secured by special clips that require radio removal tools or U-shaped coathanger wire to release. Insert the tools into the holes at the corners of the assembly until the internal clips release, then flex out on both tools while pulling the assembly out, disconnecting the antenna and electrical connectors before removing the unit from the vehicle. To install, plug in the electrical connectors, slide the radio or CD player into the instrument panel until the clips snap in place. For door-mounted speakers, remove the door trim panel, take out the mounting screws, withdraw the speaker, unplug the electrical connector, and remove the speaker from the vehicle, with installation being the reverse of removal. For rear quarter panel mounted speakers, remove the screws and pry off the speaker grille, then take out the retaining screws, withdraw the speaker, unplug the electrical connector, and remove the speaker from the vehicle, with installation being the reverse of removal. For package shelf mounted speakers, open the trunk lid, work under the package tray to unplug the electrical connector, remove the retaining screws/nuts or detach the clips, then lower the speaker and remove it from the vehicle, with installation being the reverse of removal.

Remove the door trim panel or rear quarter panel. Remove the screws securing the speaker to the trim panel or speaker bracket. Lift out the speaker and disconnect the electrical connector at the speaker, taking care not to operate the radio with the speakers disconnected. Installation is the reverse of the removal steps.

Remove the door trim panel or rear quarter panel. Remove the screws securing the speaker to the trim panel or speaker bracket. Lift out the speaker and disconnect the electrical connector at the speaker, taking care not to operate the radio with the speakers disconnected. Installation is the reverse of the removal steps.