Is it best to leave the servicing of valves, valve seats, and valve guides to a professional on Ford Bronco?

Because of the complex nature of the job and the special tools and equipment needed, servicing the valves, valve seats, and valve guides, commonly known as a valve job, is best left to a professional. The home mechanic can remove and disassemble the head, perform initial cleaning and inspection, and then reassemble and deliver the head to a dealer service department or an automotive machine shop for the actual valve servicing. The dealer service department or automotive machine shop will remove the valves and springs, recondition or replace the valves and valve seats, recondition the valve guides, check and replace the valve springs, spring retainers, and keepers as required, replace the valve seals with new ones, reassemble the valve components, and ensure the installed spring height is correct. The cylinder head gasket surface will also be resurfaced if warped. After the valve job has been performed by a professional, the head will be in like-new condition. When the head is returned, it is important to clean it again before installation on the engine to remove any metal particles and abrasive grit that may still be present from the valve service or head resurfacing operations, using compressed air if available to blow out all the oil holes and passages.

Genuine Ford Bronco Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Intake Valves found

View related parts
Ford Bronco Intake Valve
Part Number: E7TZ6507G
$18.74 MSRP: $25.61
You Save: $6.87 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Inlet; Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1987-1989 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4MT, 5MT
View related parts
Ford Bronco Valve - Inlet
Part Number: 1S7Z-6507-B
$12.29 MSRP: $17.50
You Save: $5.21 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Manufacturer Note: Intake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Bronco | 4 Cyl 2.3 L GAS
View related parts
Ford Bronco Valve - Inlet
Part Number: E3ZZ-6507-A
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1996 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT A4LD, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford Bronco VALVE - INLET
Part Number: JT4Z-6507-B
$7.83 MSRP: $11.15
You Save: $3.32 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Replaced by: JT4Z-6507-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Bronco | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Bronco Valve Intake Std
Part Number: C5TZ-6507-A
$0.00
Product Specifications
- Other Name: Valves; Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1984 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4MT
View related parts
Ford Bronco Valve - Inlet
Part Number: E7TZ-6507-D
Product Specifications
- Other Name: Valves; Valve
- Replaced by: F2TZ-6507-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1989 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4MT, 5MT
View related parts
Ford Bronco Valve Inlet
Part Number: E7TZ6507H
Product Specifications
- Other Name: Valve - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1987-1989 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4MT, 5MT
View related parts
Ford Bronco Valve - Inlet
Part Number: F4TZ-6507-AB
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1996 Ford Bronco | 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT A4LD, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford Bronco Valve Inlet
Part Number: F4TZ6507BB
Product Specifications
- Other Name: Valve - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1996 Ford Bronco | 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT A4LD, 4AT AOD, 4AT E4OD, 4MT, 5MT

Ford Bronco Intake Valve

Intake Valve found in Ford Bronco cars is widely important for improving the conduction of the engine besides monitoring the mixture of air and fuel for the purpose of realizing good combustion. These valves need to open and close at certain intervals to allow proper air fuel mixture and otherwise will compromise on the power output. Intake Valves are also used in Ford Bronco models where different styles have been installed in the cars in the past years depending on the performance requirement of the automobile. It is very important to maintaining and replacing deficient Intake Valves on time to enhance the engine and to avoid related failures that would cost a lot of money. Intake Valve replacement involves some specific tools and delicate operations to replace the Intake Valve in order to preserve the quality of the engine's operation.

We provide a wide range of Ford Bronco Intake Valve at the best prices possible. If you need Ford Bronco Intake Valve, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Bronco Intake Valve Parts Questions & Experts Answers

Valve - Inlet
F4TZ-6507-AB
Q: Is it best to leave the servicing of valves, valve seats, and valve guides to a professional on Ford Bronco?
A: Because of the complex nature of the job and the special tools and equipment needed, servicing the valves, valve seats, and valve guides, commonly known as a valve job, is best left to a professional. The home mechanic can remove and disassemble the head, perform initial cleaning and inspection, and then reassemble and deliver the head to a dealer service department or an automotive machine shop for the actual valve servicing. The dealer service department or automotive machine shop will remove the valves and springs, recondition or replace the valves and valve seats, recondition the valve guides, check and replace the valve springs, spring retainers, and keepers as required, replace the valve seals with new ones, reassemble the valve components, and ensure the installed spring height is correct. The cylinder head gasket surface will also be resurfaced if warped. After the valve job has been performed by a professional, the head will be in like-new condition. When the head is returned, it is important to clean it again before installation on the engine to remove any metal particles and abrasive grit that may still be present from the valve service or head resurfacing operations, using compressed air if available to blow out all the oil holes and passages.