How to remove and install the electric fuel pump for Ford Bronco II?

To remove the low-pressure pump in the fuel tank for 2.3L and 2.9L engines up to model year 1988, disconnect the negative battery cable, drain or remove the tank, disconnect electrical connections to the fuel system sender unit, remove dirt from around the fuel sender assembly, loosen quick connect fittings, and separate the locking ring, sender assembly, and sealing gasket. Install a fuel pump on the sender assembly, place a new sealing gasket into a groove of a tank, and install the sender assembly into it. Rotate this ring until it locks. For removal of high-pressure pump on the frame rail, disconnect negative battery cable, relieve system pressure, clean dirt/grease from fuel line fittings, disconnect quick-connect fittings properly, and pull out mounting bracket off the pump assembly. After cleaning and maintenance operations are done, reconnect electrical connections and fuel line connections, connect the battery cable, pressurize the fuel system, and check for leaks.

Genuine Ford Bronco II Fuel Pump

Gas Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Fuel Pumps found

View related parts
Ford Bronco II Fuel Pump Assembly
Part Number: E7TZ-9C407-B
$360.47 MSRP: $580.00
You Save: $219.53 (38%)
Product Specifications
- Other Name: Pump Assembly - Fuel
- Replaced by: E7TZ-9C407-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986 Ford Bronco II | 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 4MT, 5MT
View related parts
Ford Bronco II Sender And Pump Assembly
Part Number: E8TZ-9H307-E
Product Specifications
- Other Name: Sender And Pump Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1988 Ford Bronco II | 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 4MT, 5MT
View related parts
Ford Bronco II Sender And Pump Assembly
Part Number: E9TZ-9H307-D
Product Specifications
- Other Name: Sender And Pump Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989-1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 4MT, 5MT

Ford Bronco II Fuel Pump

Fuel Pump is quite important as it pumps fuel from the tank through the carburetor or fuel injection system on the Ford Bronco II. While electric pumps are found in fuel injection system, mechanical pumps are used in system that employs carburetor. Secondary suction lifts mechanical pumps which are operated by the camshaft, to deliver pressure and avoid over-pumping. Electric pumps remain inside the tank, giving you better pressures and benefits such as cooling and few risks of fire. Bigger performance fuel pumps are flow rated in GPH or LPH and generally the engine horsepower determines the type of the pump needed. In summary, the Fuel Pump plays the critical role of delivering an adequate volume and pressure of fuel to the engine for efficiency.

We provide a wide range of Ford Bronco II Fuel Pump at the best prices possible. If you need Ford Bronco II Fuel Pump, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Bronco II Fuel Pump Parts Questions & Experts Answers

Fuel Pump Assembly
E7TZ-9C407-B
Q: How to remove and install the electric fuel pump for Ford Bronco II?
A: To remove the low-pressure pump in the Fuel Tank for 2.3L and 2.9L engines up to model year 1988, disconnect the negative battery cable, drain or remove the tank, disconnect electrical connections to the fuel system sender unit, remove dirt from around the fuel sender assembly, loosen quick connect fittings, and separate the locking ring, sender assembly, and sealing gasket. Install a fuel pump on the sender assembly, place a new sealing gasket into a groove of a tank, and install the sender assembly into it. Rotate this ring until it locks. For removal of high-pressure pump on the frame rail, disconnect negative battery cable, relieve system pressure, clean dirt/grease from fuel line fittings, disconnect quick-connect fittings properly, and pull out mounting bracket off the pump assembly. After cleaning and maintenance operations are done, reconnect electrical connections and fuel line connections, connect the battery cable, pressurize the fuel system, and check for leaks.