×
- Live Chat
- 1-888-788-9341
My Garage
My Account
Cart
Genuine Ford Crown Victoria Axle Shaft
Car Axle Shaft- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
8 Axle Shafts found
Ford Crown Victoria Shaft Assembly - Rear Axle
Part Number: 3W1Z-4234-KA$202.37 MSRP: $371.67You Save: $169.30 (46%)
Ford Crown Victoria Axle Shaft
The Axle Shaft of Ford Crown Victoria vehicles is one of the most strategic parts, which transmits power from the differential to the drive wheels thus enable them to rotate independently in a manner that improves grip. These steel shafts come in different forms and these are: truck and pre-RWD car solid axles, and halfshafts where there is independent suspension. The transit axle is also solid, containing the differential and axle, with half shafts to take power from the transaxle to the wheels. Axle shafts get worn out due to rubbing against obstacles and this leads to such problems as noise and vibration while the seals get worn out, thus causing leakages of lubricants and contamination of the brakes. In summary, Axle Shaft contributes to the support of vehicles' weight, transfer of force, and special wheel positioning, particularly in Ford Crown Victoria cars.
We provide a wide range of Ford Crown Victoria Axle Shaft at the best prices possible. If you need Ford Crown Victoria Axle Shaft, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.
Ford Crown Victoria Axle Shaft Parts Questions & Experts Answers
- Q: How to remove and install the Axle Shaft on Ford Crown Victoria?A: Loosen the wheel lug nuts, raise the rear of the vehicle, support it securely on jackstands and remove the wheel. Also remove the brake drum, or the caliper and disc. Remove the cover from the differential carrier and allow the lubricant to drain into a container. Remove the lock bolt from the differential pinion shaft. Slide the notched end of the pinion shaft out of the differential case as far as ii will go. Position a large screwdriver between the rear axle case and a ring gear bolt to keep the differential case from turning when removing the pinion shaft lock bolt. Rotate the differential case 180-degrees and slide the pinion shaft out of the case until the stepped part of the shaft contacts the ring gear. Push the outer (flanged) end of the axleshaft in and remove the C-lock from the inner end of the shaft. Take care to not damage the 0- rings in the axleshaft grooves when removing the C-clips. Withdraw the axleshaft, taking care not to damage the oil seal in the end of the axle housing as the splined end of the axleshaft passes through it. Do not rotate the differential while the pinion shaft is out, or the pinion gears could fall out. Installation is the reverse of removal. Tighten the differential pinion shaft lock bolt to the torque Specifications. Install the differential cover. Refill the axle with the correct quantity and grade of lubricant.
- Q: How do you remove the rear axle assembly on Ford Crown Victoria?A: To remove the rear axle assembly, disconnect the battery cable, loosen lug nuts, raise the vehicle, remove wheels, brake components, and axle cover. Disconnect ABS sensors, axleshafts, brake lines, and backing plates. Unbolt driveshaft, raise axle, disconnect safety chain or air springs, remove shock absorbers and suspension arm bolts. Disconnect axle-locating arms, Watts-linkage assembly, and height sensor if applicable. Lower axle housing, remove coil springs or air springs. Lower suspension arm bolts, remove axle housing. For installation, raise axle, secure with suspension arm bolts, install springs, connect lower suspension arms. Raise axle to normal height, tighten suspension arm bolts, reattach height sensor if applicable. Connect shock absorbers, driveshaft, and backing plates. Reconnect sensor wires, brake lines, and parking brake cables. Install axleshafts, brake components, axle cover, and fill differential. Install wheels, lower vehicle, and tighten lug nuts.
Related Ford Crown Victoria Parts
Ford Crown Victoria Transmission Assembly
Ford Crown Victoria Torque Converter
Ford Crown Victoria Transmission Pan
Ford Crown Victoria Slip Yoke
Ford Crown Victoria Wheel Bearing
Ford Crown Victoria Pinion Washer
Ford Crown Victoria Transmission Gasket
Browse by Year
2011 Axle Shaft 2010 Axle Shaft 2009 Axle Shaft 2008 Axle Shaft 2007 Axle Shaft 2006 Axle Shaft 2005 Axle Shaft 2004 Axle Shaft 2003 Axle Shaft 2002 Axle Shaft 2001 Axle Shaft 2000 Axle Shaft 1999 Axle Shaft 1998 Axle Shaft 1997 Axle Shaft 1996 Axle Shaft 1995 Axle Shaft 1994 Axle Shaft 1993 Axle Shaft 1992 Axle Shaft