How to remove and install the transmission on Ford Crown Victoria?

To take out this transmission it is required to unplug the cable from the minus terminal of the battery and then to securely jack up the car. Solo remove the transmission pan and drain the transmission fluid, reconnect the oil cooler line fitting to avoid contamination. Some bolts will need to be removed to provide access to the torque converter so pull the torque converter cover and pull any associated plugs - Using a white marking paint, paint the torque converter and one stud so that it can easily be re-installed. Take out the torque converter-to-driveplate nuts by utilizing the crankshaft pulley until you have an access; afterward rotate the torque converter as low as possible utilizing the crankshaft pulley so that you can effectively drain the fluid then re-insert the drain plug. Disconnect the starter motor and driveshaft, cancel the speedometer cable/speed sensor, and withdraw all the electrical connectors associated with the transmission; there are also several interconnected exhaust factors which also require deletion. For AOD units, remove the TV cable, the shift cable from the manual lever and the bracket. Safely lift the engine and transmission with the jacks and take out the bolts of the mount-to-transmission extension housing and then drop the crossmember if necessary. Lower the transmission in order to unlock the fluid cooler connections and take away the top and bottom bolts connecting the transmission to the engine, and take out the dipstick tube connection. Shifting the transmission backwards thus freeing it off the dowel pins on the engine block and ensure that the torque converter is holding. The torque converter hub should be slid into the pump, lift the transmission upwards and level it, then thread the torque converter studs through the driveplate holes. Shift the transmission forward until it engages; thereafter fix and tighten the bolts that hold the transmission to the engine and the nuts holding the torque converter to the drive plate. Attach the transmission fluid cooler lines, fasten the transmission mount and crossmember bolts and there should be no need for jacks. Install the dipstick tube, oil cooler line fittings, starter motor, vacuum hoses, shift and TV linkage and the transmission wire harness connectors. Lastly, bolt the torque converter cover, driveshaft, speedo cable/sensor connector, then set the shift linkage, any exhaust parts that were removed, drop the vehicle, fill with the correct transmission fluid, start the car, and look for leaks.

Genuine Ford Crown Victoria Transmission Assembly

Trans Assembly

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

42 Transmission Assemblies found

View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 4W7Z-7000-DA
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy
- Replaced by: 4W7Z-7000-DARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 9W7Z-7000-CRM
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy; Transmission
- Manufacturer Note: Remanufactured
- Replaces: 9W7Z-7000-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: AW7Z-7000-C
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Note: For Warranty Repairs - Technical Service Hotline Prior Approval May Be Required For This Part
- Replaced by: AW7Z-7000-CRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: F7AZ-7000-BRM
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy
- Replaced by: F7AZ-7V000-BRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 4W7Z-7000-DARM
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: 4W7P-DA
- Replaces: 4W7Z-7000-DA, 4W7Z-7000-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 4W7Z-7000-FA
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy
- Replaced by: 4W7Z-7000-DARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 9W7Z-7000-B
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Note: For Warranty Repairs - Technical Service Hotline Prior Approval May Be Required For This Part
- Replaced by: 9W7Z-7000-CRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 7W7Z-7000-C
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Note: For Warranty Repairs - Technical Service Hotline Prior Approval May Be Required For This Part
- Replaced by: 7W7Z-7000-CARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 7W7Z-7000-CARM
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Remanufactured
- Replaces: 7W7Z-7000-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: AW7Z-7000-CRM
$3147.48 MSRP: $3732.00
You Save: $584.52 (16%)
Product Specifications
- Other Name: Automatic Transmission Assy; Transmission
- Manufacturer Note: Remanufactured
- Replaces: AW7Z-7000-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 1W7Z-7000-AARM
Product Specifications
- Other Name: Automatic Transmission Assy
- Replaced by: 1W7Z-7V000-ARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 1W7Z-7000-CARM
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: 4.6L/4R70W - Police Package - 1W7P-C*
- Replaced by: 1W7Z-7V000-CRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 1W7Z-7000-DARM
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: 4.6L/4R70W - 1W7P-D*
- Replaced by: 1W7Z-7V000-DRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 3W7Z-7000-AARM
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Note: Availability will be announced on DOES II, 4.6L/4R70W - 3W7P-AA,BA
- Replaced by: 3W7Z-7V000-ARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 3W7Z-7000-CA
Product Specifications
- Other Name: Automatic Transmission Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 3W7Z-7000-CARM
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Note: Availability will be announced on DOES II, 4.6L/4R70W - Police package - 3W7P-CA,EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 3W7Z-7000-DA
Product Specifications
- Other Name: Automatic Transmission Assy
- Replaced by: 3W7Z-7V000-DRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 3W7Z-7000-DARM
Product Specifications
- Other Name: Automatic Transmission Assy
- Manufacturer Note: Note: Availability will be announced on DOES II, 4.6L/4R70W - 3W7P-DA
- Replaced by: 3W7Z-7V000-DRM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 3W7Z-7000-EA
Product Specifications
- Other Name: Automatic Transmission Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Automatic Transmission Assembly
Part Number: 4W7Z-7000-AA
Product Specifications
- Other Name: Automatic Transmission Assy
- Replaced by: 4W7Z-7000-AARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W

| Page 1 of 3 |Next >

1-20 of 42 Results

Ford Crown Victoria Transmission Assembly

We provide a wide range of Ford Crown Victoria Transmission Assembly at the best prices possible. If you need Ford Crown Victoria Transmission Assembly, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Crown Victoria Transmission Assembly Parts Questions & Experts Answers

Automatic Transmission Assembly
F6AZ-7000-AARM
Q: How to remove and install the transmission on Ford Crown Victoria?
A: To take out this transmission it is required to unplug the cable from the minus terminal of the battery and then to securely jack up the car. Solo remove the transmission pan and drain the transmission fluid, reconnect the oil cooler line fitting to avoid contamination. Some bolts will need to be removed to provide access to the torque converter so pull the torque converter cover and pull any associated plugs - Using a white marking paint, paint the torque converter and one stud so that it can easily be re-installed. Take out the torque converter-to-driveplate nuts by utilizing the crankshaft pulley until you have an access; afterward rotate the torque converter as low as possible utilizing the crankshaft pulley so that you can effectively drain the fluid then re-insert the drain plug. Disconnect the starter motor and driveshaft, cancel the speedometer cable/speed sensor, and withdraw all the electrical connectors associated with the transmission; there are also several interconnected exhaust factors which also require deletion. For AOD units, remove the TV cable, the shift cable from the manual lever and the bracket. Safely lift the engine and transmission with the jacks and take out the bolts of the mount-to-transmission extension housing and then drop the crossmember if necessary. Lower the transmission in order to unlock the fluid cooler connections and take away the top and bottom bolts connecting the transmission to the engine, and take out the dipstick tube connection. Shifting the transmission backwards thus freeing it off the dowel pins on the engine block and ensure that the torque converter is holding. The torque converter hub should be slid into the pump, lift the transmission upwards and level it, then thread the torque converter studs through the driveplate holes. Shift the transmission forward until it engages; thereafter fix and tighten the bolts that hold the transmission to the engine and the nuts holding the torque converter to the drive plate. Attach the transmission fluid cooler lines, fasten the transmission mount and crossmember bolts and there should be no need for jacks. Install the dipstick tube, oil cooler line fittings, starter motor, vacuum hoses, shift and TV linkage and the transmission wire harness connectors. Lastly, bolt the torque converter cover, driveshaft, speedo cable/sensor connector, then set the shift linkage, any exhaust parts that were removed, drop the vehicle, fill with the correct transmission fluid, start the car, and look for leaks.

Related Ford Crown Victoria Parts

Browse by Year

2011 Transmission Assembly 2010 Transmission Assembly 2009 Transmission Assembly 2008 Transmission Assembly 2007 Transmission Assembly 2004 Transmission Assembly 2003 Transmission Assembly 2002 Transmission Assembly 2001 Transmission Assembly 2000 Transmission Assembly 1999 Transmission Assembly 1998 Transmission Assembly 1997 Transmission Assembly 1996 Transmission Assembly