How do you check and replace a transmission mount on Ford Crown Victoria?

Place a large screwdriver or prybar between the transmission extension housing and the crossmember with the slender edge of this tool upward and pry the transmission a bit upward. To check the transmission mount it's necessary to insert a thin screwdriver between the crossmember and the mount and try to slide it-there should be almost no way the screwdriver would slide. If there is a large amount of movement remove the mount by undoing the nuts which secure the mount to the crossmember, then undoing the bolts which fasten the mount to the transmission extension housing. After that, lift the transmission with a jack just a little and then unbolt the mount. For installation, the reverse of this procedure should be taken; however, nuts and bolts should be tightened before everything else.

Genuine Ford Crown Victoria Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Motor And Transmission Mounts found

View related parts
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: 3W1Z-6038-BA
$59.74 MSRP: $87.33
You Save: $27.59 (32%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Front Mount, Mount
- Manufacturer Note: LH, FRONT
- Position: Driver Side,Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Motor Mount
Part Number: 3W1Z-6038-BB
$62.04 MSRP: $94.00
You Save: $31.96 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assy; Front Mount, Mount
- Manufacturer Note: RH, front, police, taxi, fleet, limo - severe duty
- Position: Passenger Side,Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Transmission Mount
Part Number: 3W1Z-6068-BA
$38.16 MSRP: $54.83
You Save: $16.67 (31%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Rear Mount
- Manufacturer Note: Insulator & retainer, rear engine support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: F8VZ-6068-AA
$126.62 MSRP: $175.90
You Save: $49.28 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Rear Mount, Transmission Mount
- Replaces: F4VY-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Insulator Assembly Engine S
Part Number: F2AZ6068B
$49.91 MSRP: $68.20
You Save: $18.29 (27%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assy - Engine Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Front Mount
Part Number: 3W7Z-6038-AA
$66.23 MSRP: $96.83
You Save: $30.60 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assy; Mount
- Manufacturer Note: RH, front, same as 3W1Z-6038-BB but without the heat shield, for lighter duty., not for police, taxi, limo or fleet.
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: 1W7Z-6038-BA
$54.55 MSRP: $75.78
You Save: $21.23 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Front Mount, Mount
- Manufacturer Note: LH, with shield
- Position: Driver Side
- Replaces: F8VZ-6038-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Insulator Assembly
Part Number: F4AZ-6038-A
$53.11 MSRP: $73.78
You Save: $20.67 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assy; Front Mount, Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: F8VZ-6038-AA
Product Specifications
- Other Name: Insulator Assembly - Engine Support
- Manufacturer Note: LH, without shield
- Position: Driver Side
- Replaced by: 1W7Z-6038-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Engine Support Insulator Assembly
Part Number: F4AZ-6038-B
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Front Mount, Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E

Ford Crown Victoria Motor And Transmission Mount

The Motor And Transmission Mount in Ford Crown Victoria family cars is a very important part as it is responsible for firmly fixing the transmission and at the same time protecting it from the forces of vibrations from the engine. The role of this component is crucial in the regulation and control of the sturdiness and efficiency of the vehicle's drive train. As for the type of the transmission used in the Ford Crown Victoria there can be one or multiple Motor And Transmission Mount depending on the exact setup. There are several types of Motor And Transmission Mounts for the Ford Crown Victoria, most of them have been used in the vehicles over the years to successfully maintain proper position of the transmission as well as to control vibrations. The variations between these type may lie in how it is constructed and how many mount is employed, which may affect the experience of the ride or the level of comfort that the rider gets.

We provide a wide range of Ford Crown Victoria Motor And Transmission Mount at the best prices possible. If you need Ford Crown Victoria Motor And Transmission Mount, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Crown Victoria Motor And Transmission Mount Parts Questions & Experts Answers

Engine Support Insulator Assembly
3W1Z-6038-BA
Q: How do you check and replace a transmission mount on Ford Crown Victoria?
A: Place a large screwdriver or prybar between the transmission extension housing and the crossmember with the slender edge of this tool upward and pry the transmission a bit upward. To check the transmission mount it's necessary to insert a thin screwdriver between the crossmember and the mount and try to slide it-there should be almost no way the screwdriver would slide. If there is a large amount of movement remove the mount by undoing the nuts which secure the mount to the crossmember, then undoing the bolts which fasten the mount to the transmission extension housing. After that, lift the transmission with a jack just a little and then unbolt the mount. For installation, the reverse of this procedure should be taken; however, nuts and bolts should be tightened before everything else.