How to install and remove the hood latch and release cable on Ford Edge?

To fit the hood latch, one has to reverse the observed procedure of fitting the grille shutter by making a note of the fact that the active grille shutter has to be removed where the model is 2015 and above. Draw a pencil line around the latch for alignment purpose and then unbolt the retaining bolts that hold the hood latch to the radiator support and pull out the latch. After that, it is necessary to put the pressure on the cable retainer to free it from the latch assembly and to detach the cable end plug. For the release cable, it is up in the engine compartment that is where you have to get rid of the hood latch and also free the hood release cable from the latch. Remove the two release cable clips from the radiator support, undo the left front wheellug nuts, safely jack up the car on jack stands and remove the wheel, also take off the inner fender splash shield. Pull free the two latches on the top of the fender opening to release the cable from its clips and to release the cable clip from the wiring harness though on some models it may be required to remove the Smart Junction Box. Last but not least, it is necessary to remove the two hood release handle mounting bolts, to take out the hood release handle, to disconnect the release cable from the release handle and to pull the cable through the fire wall.

Genuine Ford Edge Hood Latch

Engine Hood Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Hood Latches found

View related parts
Ford Edge Hood Latch Assembly
Part Number: KT4Z-16700-A
$81.82 MSRP: $119.62
You Save: $37.80 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly - Hood; Latch, Lock
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2024 Ford Edge | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Edge Latch Assembly - Hood
Part Number: 6E5Z-16700-AA
$25.29 MSRP: $36.97
You Save: $11.68 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assy - Hood; Latch, Lock
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Latch Assembly - Hood
Part Number: FT4Z-16700-A
$80.51 MSRP: $117.70
You Save: $37.19 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assy - Hood; Latch, Lock
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2021 Ford Edge | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS), 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 2.7 L GAS, 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)

Ford Edge Hood Latch

Hood Latch found in Ford Edge cars is very important because it helps in preventing the hood from opening while the car is being driven. This mechanism proves very useful since it helps to protect such delicate parts as the engine, the radiator, and battery against harm. In the course of time, different design of the Hood Latch have been installed in models of the Ford Edge car aimed at increasing the reliability of the car. While specific differences between these styles may not be detailed, the primary goal remains consistent: for the reason of sealing the hood to prevent it from being opened when the car is on motion. The Ford Edge Hood Latch is a part that basically helps in protecting the important components of the vehicle hence plays a pivotal role in the safety of the car.

We provide a wide range of Ford Edge Hood Latch at the best prices possible. If you need Ford Edge Hood Latch, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Edge Hood Latch Parts Questions & Experts Answers

Latch Assembly - Hood
6E5Z-16700-AA
Q: How to install and remove the hood latch and release cable on Ford Edge?
A: To fit the hood latch, one has to reverse the observed procedure of fitting the grille shutter by making a note of the fact that the active grille shutter has to be removed where the model is 2015 and above. Draw a pencil line around the latch for alignment purpose and then unbolt the retaining bolts that hold the hood latch to the radiator support and pull out the latch. After that, it is necessary to put the pressure on the cable retainer to free it from the latch assembly and to detach the cable end plug. For the release cable, it is up in the engine compartment that is where you have to get rid of the hood latch and also free the hood release cable from the latch. Remove the two release cable clips from the radiator support, undo the left front wheellug nuts, safely jack up the car on jack stands and remove the wheel, also take off the inner fender splash shield. Pull free the two latches on the top of the fender opening to release the cable from its clips and to release the cable clip from the wiring harness though on some models it may be required to remove the Smart Junction Box. Last but not least, it is necessary to remove the two hood release handle mounting bolts, to take out the hood release handle, to disconnect the release cable from the release handle and to pull the cable through the fire wall.