How to remove and replace a Clutch Disc,Clutch Fork,Pressure Plate and Release Bearing in a Ford Escape?

Dust produced by clutch wear is hazardous to your health. Do not blow it out with compressed air or inhale it. Avoid using gasoline or petroleum-based solvents to remove the dust. Use brake system cleaner to flush the dust into a drain pan. After the clutch components are wiped clean with a rag, dispose of the contaminated rags and cleaner in a covered, marked container.To remove the clutch, access to its components is normally achieved by removing the transaxle, leaving the engine in the vehicle. Check the clutch for wear and replace worn components as necessary when the engine is being removed for major overhaul. However, the relatively low cost of the clutch components compared to the time and trouble spent gaining access to them warrants their replacement anytime the engine or transaxle is removed, unless they are new or in near perfect condition. Remove the transaxle from the vehicle. Support the engine while the transaxle is out, preferably using an engine support fixture or a hoist from above. The clutch fork and release bearing can remain attached to the transaxle housing for the time being. To support the clutch disc during removal, install a clutch alignment tool through the clutch disc hub.Carefully inspect the flywheel and pressure plate for indexing marks. If they cannot be found, scribe or paint marks yourself so the pressure plate and the flywheel will be in the same alignment during installation. Loosen the pressure plate-to-flywheel bolts in a criss-cross pattern until all spring pressure is relieved. Then, hold the pressure plate securely and completely remove the bolts, followed by the pressure plate and clutch disc.When inspecting clutch components, look for problems such as wear on the clutch disc. Inspect the flywheel for cracks, heat checking, grooves and other obvious defects. A machine shop can smoothen slight imperfections. Inspect the clutch disc lining and replace it if in doubt about its condition. The release bearing should also be replaced along with the clutch disc.Check the machined surfaces and the diaphragm spring fingers of the pressure plate. If damaged, replace the pressure plate. Check the pilot bearing in the end of the crankshaft for excessive wear and replace it if necessary. To remove the pilot bearing, use a slide hammer and puller attachment.To install a new pilot bearing, lightly lubricate the outside surface with grease, then drive it into the recess with a bearing driver or a socket. Clean the flywheel and pressure plate machined surfaces with brake cleaner, lacquer thinner, or acetone before installation. No oil or grease should be on these surfaces or the lining of the clutch disc.Position the clutch disc and pressure plate against the flywheel with the clutch held in place with an alignment tool. Ensure the disc is installed properly. Tighten the pressure plate-to-flywheel bolts only finger tight, working around the pressure plate. Center the clutch disc by ensuring the alignment tool extends through the splined hub and into the pilot bearing in the crankshaft. Tighten the bolts in a criss-cross pattern to prevent distorting the cover and remove the alignment tool.Lubricate the inner groove of the release bearing with high-temperature grease. Also, place a small amount of grease on the release lever contact areas and the transaxle input shaft bearing retainer. Install the clutch release bearing. Install the transaxle and all components removed previously.

Genuine Ford Escape Pressure Plate

Clutch Pressure Plate

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Pressure Plates found

View related parts
Ford Escape Plate - Clutch Pressure
Part Number: 9L8Z-7B066-C
$18.92 MSRP: $27.67
You Save: $8.75 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2019 Ford Escape | 4 Cyl 1.5L EcoBoost 16V (180PS), 4 Cyl 1.6L EcoBoost SCTi -Sigma, 4 Cyl 2.0L, 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) , 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L OHC Duratec | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: CV6Z-7B066-A
$27.02 MSRP: $39.50
You Save: $12.48 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 9L8Z-7B066-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2019 Ford Escape | 4 Cyl 1.5L EcoBoost 16V (180PS), 4 Cyl 1.6L EcoBoost SCTi -Sigma, 4 Cyl 2.0L, 4 Cyl 2.0L EcoBoost (240PS), 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS), 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L OHC Duratec | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: 9L8Z-7B066-D
$9.32 MSRP: $13.28
You Save: $3.96 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: Forward Clutch Pressure Plate
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2015 Ford Escape | 4 Cyl 1.6L EcoBoost SCTi -Sigma, 4 Cyl 2.0L, 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) , 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L OHC Duratec | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive)
View related parts
Ford Escape Drive Plate - Clutch
Part Number: F3RZ-7B066-D
$15.37 MSRP: $21.00
You Save: $5.63 (27%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: F2GZ-7B066-A
$11.16 MSRP: $16.32
You Save: $5.16 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: Forward Clutch Pressure Plate
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2019 Ford Escape | 4 Cyl 1.5L EcoBoost 16V (180PS), 4 Cyl 1.6L EcoBoost SCTi -Sigma, 4 Cyl 2.0L, 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: F8RZ-7B066-AA
$14.93 MSRP: $21.83
You Save: $6.90 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: 9L8Z-7B066-B
$27.02 MSRP: $39.50
You Save: $12.48 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: CV6Z-7B066-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L OHC Duratec | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Escape Plate Assembly - Clutch Pressure
Part Number: 5L8Z-7563-ACRM
$328.83 MSRP: $447.69
You Save: $118.86 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate Assy - Clutch Pressure
- Replaced by: 9L8Z-7B546-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Escape | 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 5-Speed Manual Transmission - AK, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Plate Assembly - Clutch Pressure
Part Number: YL8Z-7563-AA
$148.20 MSRP: $200.00
You Save: $51.80 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate Assy - Clutch Pressure
- Replaced by: 3L8Z-7L596-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | 4 Cyl 2.0L Zetec EFI, 6 Cyl 3.0L DOHC EFI Modular | 5-Speed Manual Transmission, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Drive Plate - Clutch
Part Number: F3RZ-7B066-B
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2006 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Plate Assembly - Clutch Pressure
Part Number: F3RZ-7B477-A
Product Specifications
- Other Name: Plate Assy - Clutch Pressure
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: F8RZ-7B066-BA
Product Specifications
- Replaces: F3RZ-7B066-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Drive Plate - Clutch
Part Number: F3RZ-7B066-F
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Plate - Clutch Pressure
Part Number: F3RZ-7D408-A
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Ford Escape Drive Plate - Clutch
Part Number: F3RZ-7B066-E
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Escape | 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)

Ford Escape Pressure Plate Parts Questions & Experts Answers

Plate - Clutch Pressure
9L8Z-7B066-C
Q: How to remove and replace a Clutch Disc,Clutch Fork,Pressure Plate and Release Bearing in a Ford Escape?
A: Dust produced by clutch wear is hazardous to your health. Do not blow it out with compressed air or inhale it. Avoid using gasoline or petroleum-based solvents to remove the dust. Use brake system cleaner to flush the dust into a drain pan. After the clutch components are wiped clean with a rag, dispose of the contaminated rags and cleaner in a covered, marked container.To remove the clutch, access to its components is normally achieved by removing the transaxle, leaving the engine in the vehicle. Check the clutch for wear and replace worn components as necessary when the engine is being removed for major overhaul. However, the relatively low cost of the clutch components compared to the time and trouble spent gaining access to them warrants their replacement anytime the engine or transaxle is removed, unless they are new or in near perfect condition. Remove the transaxle from the vehicle. Support the engine while the transaxle is out, preferably using an engine support fixture or a hoist from above. The clutch fork and release bearing can remain attached to the transaxle housing for the time being. To support the clutch disc during removal, install a clutch alignment tool through the clutch disc hub.Carefully inspect the flywheel and pressure plate for indexing marks. If they cannot be found, scribe or paint marks yourself so the pressure plate and the flywheel will be in the same alignment during installation. Loosen the pressure plate-to-flywheel bolts in a criss-cross pattern until all spring pressure is relieved. Then, hold the pressure plate securely and completely remove the bolts, followed by the pressure plate and clutch disc.When inspecting clutch components, look for problems such as wear on the clutch disc. Inspect the flywheel for cracks, heat checking, grooves and other obvious defects. A machine shop can smoothen slight imperfections. Inspect the clutch disc lining and replace it if in doubt about its condition. The release bearing should also be replaced along with the clutch disc.Check the machined surfaces and the diaphragm spring fingers of the pressure plate. If damaged, replace the pressure plate. Check the pilot bearing in the end of the crankshaft for excessive wear and replace it if necessary. To remove the pilot bearing, use a slide hammer and puller attachment.To install a new pilot bearing, lightly lubricate the outside surface with grease, then drive it into the recess with a bearing driver or a socket. Clean the flywheel and pressure plate machined surfaces with brake cleaner, lacquer thinner, or acetone before installation. No oil or grease should be on these surfaces or the lining of the clutch disc.Position the clutch disc and pressure plate against the flywheel with the clutch held in place with an alignment tool. Ensure the disc is installed properly. Tighten the pressure plate-to-flywheel bolts only finger tight, working around the pressure plate. Center the clutch disc by ensuring the alignment tool extends through the splined hub and into the pilot bearing in the crankshaft. Tighten the bolts in a criss-cross pattern to prevent distorting the cover and remove the alignment tool.Lubricate the inner groove of the release bearing with high-temperature grease. Also, place a small amount of grease on the release lever contact areas and the transaxle input shaft bearing retainer. Install the clutch release bearing. Install the transaxle and all components removed previously.

Related Ford Escape Parts

Browse by Year

2019 Pressure Plate 2018 Pressure Plate 2017 Pressure Plate 2016 Pressure Plate 2015 Pressure Plate 2014 Pressure Plate 2013 Pressure Plate 2012 Pressure Plate 2011 Pressure Plate 2010 Pressure Plate 2009 Pressure Plate 2008 Pressure Plate 2007 Pressure Plate 2006 Pressure Plate 2005 Pressure Plate 2004 Pressure Plate 2003 Pressure Plate 2002 Pressure Plate 2001 Pressure Plate