How do I remove the under dash panel and locate the brake light switch assembly on Ford Explorer?

Remove under dash panel. Locate brake light switch near top of brake pedal and disconnect from pedal by removing retaining clip. Use screwdriver to unlock electrical connector, then unplug from switch. Use screwdriver to disengage locking tab from connector. Install switch to connector by snapping clip into place. Reconnect assembly to pedal. Install under dash panel. Check brake lights for proper operation.

What is the purpose of the brake on-off switch on Ford Explorer?

The brake light switch, also known as the brake pedal position switch or brake light switch, informs the PCM when the brakes are being applied. This switch closes when brakes are applied and opens when they are released, and is mounted on the brake pedal. The brake light circuit is controlled by this switch, and issues such as burned-out bulbs or other circuit problems can cause the engine to idle roughly. Therefore, it's important to check the brake light switch operation when troubleshooting any rough-idle problems. To identify the functions of connector terminals, wiring diagrams can be used. Disconnect the switch connector and connect your voltmeter positive (+) lead to the connector terminal that provides battery positive (B+) voltage to the switch. Connect the negative (-) meter lead to a good ground. Turn the ignition On and read the meter. It should indicate more than 10 volts or close to battery voltage. Connect an ohmmeter to the switch terminals and manually open and close the switch. The meter should alternate from continuity to an open-circuit reading as the switch is opened and closed. Also, check continuity from the switch to the brake light bulbs. Replace any burned-out bulbs or damaged wire looms. Replacement of the switch is covered.

Genuine Ford Explorer Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Brake Light Switches found

View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: GL3Z-13480-A
$30.11 MSRP: $53.09
You Save: $22.98 (44%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Stoplamp Switch, Washer Pump
- Replaces: 7T4Z-13480-AA, 8T4Z-13480-A, SW-6892
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2023 Ford Explorer | 4 Cyl 2.0L EcoBoost (240PS), 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC, 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: 8T4Z-13480-A
$30.11 MSRP: $53.09
You Save: $22.98 (44%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Stop Light
- Replaced by: GL3Z-13480-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2017 Ford Explorer | 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.3L TIVCT DI TC, 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC, 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: F87Z-13480-AA
$28.04 MSRP: $44.73
You Save: $16.69 (38%)
ADD TO CART
Product Specifications
- Other Name: Stoplamp Switch
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-1999 Ford Explorer | 6 Cyl 4.0L, 8 Cyl 5.0L | 4AT 4R70W, 5AT 5R55E, 5MT
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: 4L2Z-13480-AB
$39.99 MSRP: $79.45
You Save: $39.46 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Stop Light; Stoplamp Switch
- Manufacturer Note: Service Kit
- Replaces: 4L2Z-13480-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2004 Ford Explorer | 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L Romeo SOHC EFI | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: 4L2Z-13480-AA
$39.99 MSRP: $79.45
You Save: $39.46 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Stop Light
- Replaced by: 4L2Z-13480-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Explorer | 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L Romeo SOHC EFI | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: E9TZ-13480-A
$19.04 MSRP: $30.36
You Save: $11.32 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Stop Light; Stoplamp Switch
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Explorer | 6 Cyl 4.0L, 8 Cyl 5.0L | 4AT 4R70W, 5AT 5R55E, 5MT
- 1995-1997 Ford Explorer | 6 Cyl 4.0L, 8 Cyl 5.0L | 4AT 4R44E, 4AT 4R55E, 4AT 4R70W, 4AT A4LD, 4AT AODE-E, 4AT AODE-W, 5AT 5R55E, 5MT
- 1991-1992 Ford Explorer | 6 Cyl 4.0L | 5MT
View More
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: 3M5Z-13480-AB
$22.69 MSRP: $36.18
You Save: $13.49 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Stop Light; Stoplamp Switch
- Replaces: 3M5Z-13480-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Explorer | 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: 3M5Z-13480-AA
$22.69 MSRP: $36.18
You Save: $13.49 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Stop Light
- Replaced by: 3M5Z-13480-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Explorer | 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Explorer Switch Assembly - Stop Light
Part Number: FOOY-13480-B
$0.00
Product Specifications
- Other Name: Switch Assy - Stop Light; Stoplamp Switch
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Explorer | 6 Cyl 4.0L SOHC EFI, 8 Cyl 4.6L Romeo SOHC EFI | 5-Speed Automatic Transmission 5R55S, 5-Speed Automatic Transmission 5R55W, 5-Speed Manual Transmission (M5R4), 6-Speed Automatic Transmission (6R80), 6-Speed Automatic Transmission 6R60, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Right Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)

Ford Explorer Brake Light Switch

The Brake Light Switch used in all Ford Explorer models is functional in the sense that it produces an action of switching on the brake light whenever the brake pedal is pressed. This mechanism helps to prevent collision by making drivers behind the Explorer to notice any instance where the vehicle behind is decelerating or stopping. Information regarding the different types or actually, the styles of Brake Light Switch that's installed on different Explorer models are not clearly given but the basic working of the switch, is the same even in these type of vehicles. Design of the switch is part of it and offers a steady sign for the other motorists out there. As a whole, the Brake Light Switch is important for informational purposes to avoid hazardous circumstances, when people are on the road.

We provide a wide range of Ford Explorer Brake Light Switch at the best prices possible. If you need Ford Explorer Brake Light Switch, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Explorer Brake Light Switch Parts Questions & Experts Answers

Switch Assembly - Stop Light
E9TZ-13480-A
Q: How do I remove the under dash panel and locate the brake light switch assembly on Ford Explorer?
A: Remove under dash panel. Locate brake light switch near top of brake pedal and disconnect from pedal by removing retaining clip. Use screwdriver to unlock electrical connector, then unplug from switch. Use screwdriver to disengage locking tab from connector. Install switch to connector by snapping clip into place. Reconnect assembly to pedal. Install under dash panel. Check brake lights for proper operation.
Switch Assembly - Stop Light
F87Z-13480-AA
Q: What is the purpose of the brake on-off switch on Ford Explorer?
A: The brake light switch, also known as the brake pedal position switch or brake light switch, informs the PCM when the brakes are being applied. This switch closes when brakes are applied and opens when they are released, and is mounted on the brake pedal. The brake light circuit is controlled by this switch, and issues such as burned-out bulbs or other circuit problems can cause the engine to idle roughly. Therefore, it's important to check the brake light switch operation when troubleshooting any rough-idle problems. To identify the functions of connector terminals, wiring diagrams can be used. Disconnect the switch connector and connect your voltmeter positive (+) lead to the connector terminal that provides battery positive (B+) voltage to the switch. Connect the negative (-) meter lead to a good ground. Turn the ignition On and read the meter. It should indicate more than 10 volts or close to battery voltage. Connect an ohmmeter to the switch terminals and manually open and close the switch. The meter should alternate from continuity to an open-circuit reading as the switch is opened and closed. Also, check continuity from the switch to the brake light bulbs. Replace any burned-out bulbs or damaged wire looms. Replacement of the switch is covered.