How to remove and install the crankshaft pulley and front crankshaft seal in V8 engine on Ford F-150?

To take out the crankshaft pulley, let pull out the cable from the negative terminal of the battery and set down that of the drive-belt. For 2010 and earlier models raise the vehicle properly on jackstands and take out the engine cooling fan and shroud assembly. Take off the crankshaft pulley center bolt with the socket and breaker bar; when doing this, make sure that the pulley is locked in position with a strap or the chain wrench and place a shop rag or a piece of drivebelt material around the crankshaft pulley. If there are holes provided on the pulley to thread in, then a bolt type puller should be used but where there are no holes, then the pulley should be pulled off using a three jawed puller. There is always the need for an adapter between the puller bolt and the crankshaft so as not to damage them. Third, employ a seal puller to remove the crankshaft front oil seal without scratching the crankshaft or damage the bore. Clean the crossland bore and check for nicks or gouges and also the hub zone for signs of abnormal wearing. As for the installation, there is a requirement of a new bolt for the 5.0L and 6.2L engines to reinstall the crankshaft pulley. Slather the external lip of the new seal with clean engine oil before forcing it into place with the use of a seal driver or a socket that is a little smaller than the seal while the 'open-end' must be facing the engine. Any contact surface of the crankshaft pulley hub with the oil seal must be smeared with multi-purpose grease or clean engine oil and the front end of the keyway in the crankshaft pulley must be treated with RTV sealant before assembling. Withdraw the crankshaft pulley with an especial installation tool without the need for a hammer and fasten the center bolt and torque it to the recommended value. The remaining steps are-again-the reverse order of removal steps.

Genuine Ford F-150 Crankshaft Pulley

Crankshaft Pulley Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

40 Crankshaft Pulleys found

View related parts
Ford F-150 Crankshaft Pulley
Part Number: 7L3Z-6312-A
$107.50 MSRP: $157.17
You Save: $49.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Pulley, Vibration Damper
- Replaces: 2L1Z-6312-AA, 2L7Z-6312-A, 7L3Z-6312-B, 2L7Z-6312-AA, 5L3Z-6312-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2010 Ford F-150 | 8 Cyl 5.4L | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 4AT, 4AT 4R100, 4AT 4R70W, 5-Speed Manual Transmission - Mazda M5R2-C, 5MT, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Compressor Pulley
Part Number: F2UZ-6A312-A
$55.45 MSRP: $79.67
You Save: $24.22 (31%)
ADD TO CART
Product Specifications
- Other Name: Pulley - Compressor; Crankshaft Pulley, Pulley
- Manufacturer Note: #E9TA 6312-BA
- Replaced by: F2UZ-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1996 Ford F-150 | 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Damper
Part Number: E8TZ-6316-B
$112.97 MSRP: $165.17
You Save: $52.20 (32%)
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Vibration Damper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1995 Ford F-150 | 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 3MT, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Crankshaft Pulley
Part Number: EL3Z-6312-A
$97.36 MSRP: $142.33
You Save: $44.97 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Vibration Damper
- Manufacturer Note: 4 Rib Design
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2017 Ford F-150 | 8 Cyl 5.0L MOD DOHC SEFI NA | 10-Speed Automatic Transmission (10R80), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Crankshaft Pulley
Part Number: E4TZ-6316-A
$118.56 MSRP: $173.33
You Save: $54.77 (32%)
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Damper, Vibration Damper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1995 Ford F-150 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L | 3AT C5, 3AT C6, 3MT, 4AT 4R70W, 4AT 4R75W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 Crankshaft Pulley
Part Number: 7L3Z-6312-B
$107.50 MSRP: $157.17
You Save: $49.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft
- Replaced by: 7L3Z-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford F-150 | 8 Cyl 5.4L | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Crankshaft Pulley
Part Number: 2L1Z-6312-AA
$107.50 MSRP: $157.17
You Save: $49.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft
- Replaced by: 7L3Z-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2004 Ford F-150 | 8 Cyl 5.4L | 4AT, 4AT 4R100, 4AT 4R70W, 5MT
View related parts
Ford F-150 Crankshaft Pulley
Part Number: 2L7Z-6312-A
$107.50 MSRP: $157.17
You Save: $49.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft
- Replaced by: 7L3Z-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford F-150 | 8 Cyl 5.4L | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Crankshaft Pulley
Part Number: 2L7Z-6312-AA
$107.50 MSRP: $157.17
You Save: $49.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft
- Manufacturer Note: 4V
- Replaced by: 7L3Z-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford F-150 | 8 Cyl 5.4L | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 PULLEY - CRANKSHAFT
Part Number: NL3Z-6312-A
$91.41 MSRP: $138.50
You Save: $47.09 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley, Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | 6 Cyl 2.7 L GAS
View related parts
Ford F-150 Crankshaft Pulley
Part Number: HL3Z-6312-A
$75.49 MSRP: $137.50
You Save: $62.01 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2023 Ford F-150 | 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L GTDI | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Crankshaft Pulley
Part Number: BR3Z-6312-D
$136.80 MSRP: $200.00
You Save: $63.20 (32%)
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Pulley, Vibration Damper
- Replaces: BR3Z-6312-C, BR3Z-6312-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2017 Ford F-150 | 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC TIVCT, 6 Cyl 3.5L GTDI, 6 Cyl 3.7L PFI NA | 10-Speed Automatic Transmission (10R80), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 PULLEY - CRANKSHAFT
Part Number: NR3Z-6312-A
$124.26 MSRP: $181.67
You Save: $57.41 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley, Pulley
- Replaces: KR3Z-6312-B, JR3Z-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford F-150 | 8 Cyl 5.2 L GAS
View related parts
Ford F-150 Crankshaft Pulley
Part Number: 1L3Z-6312-AA
$275.72 MSRP: $406.67
You Save: $130.95 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft
- Manufacturer Note: Lightning
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2004 Ford F-150 | 8 Cyl 5.4L | 4AT, 4AT 4R100, 4AT 4R70W, 5MT
View related parts
Ford F-150 Crankshaft Pulley
Part Number: BC3Z-6312-A
$174.42 MSRP: $255.00
You Save: $80.58 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Vibration Damper
- Replaced by: NC3Z-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2014 Ford F-150 | 8 Cyl 6.2L OHC NA | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Crankshaft Pulley
Part Number: JL3Z-6312-A
$128.82 MSRP: $188.33
You Save: $59.51 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Pulley, Vibration Damper
- Replaced by: NL3Z-6312-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2019 Ford F-150 | 8 Cyl 5.0L Coyote | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Compressor Pulley
Part Number: E9AZ-6A312-A
$55.45 MSRP: $79.67
You Save: $24.22 (31%)
ADD TO CART
Product Specifications
- Other Name: Pulley - Compressor; Pulley
- Replaced by: F2UZ-6312-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1991 Ford F-150 | 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-150 PULLEY - CRANKSHAFT
Part Number: ML3Z-6312-B
$111.61 MSRP: $163.17
You Save: $51.56 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Pulley, Pulley
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
Ford F-150 Crankshaft Pulley
Part Number: BR3Z-6312-B
$136.80 MSRP: $200.00
You Save: $63.20 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft
- Replaced by: BR3Z-6312-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford F-150 | 6 Cyl 3.5L DOHC TIVCT, 6 Cyl 3.7L PFI NA | 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R75E W/TSS, 5-Speed Manual Transmission - Mazda M5R2-C, 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford F-150 Crankshaft Pulley
Part Number: JL3Z-6312-B
$344.65 MSRP: $508.33
You Save: $163.68 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - Crankshaft; Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford F-150 | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.0L 4V DOHC TC DSL-LION B | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)

| Page 1 of 2 |Next >

1-20 of 40 Results

Ford F-150 Crankshaft Pulley

The Performance Crankshaft Pulley found in the Ford F-150 vehicles play an important role in delivering power from the engine to other parts such as the power steering pump, A/C compressor as well as the alternator. Settling on one end of the engine crankshaft the Performance Crankshaft Pulley captures torque output improving overall performance. At the same time, it performs a harmonic balance wheel that helps to reduce vibrations that occur during the operation of the engine. Through the Ford F-150 versions, different Performance Crankshaft Pulley styles have been applied with the aim of enhancing the power train while lowering the crankshaft's mass. These may be either in material or design and may affect the premier performance of the devices in enhancing performance.

We provide a wide range of Ford F-150 Crankshaft Pulley at the best prices possible. If you need Ford F-150 Crankshaft Pulley, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford F-150 Crankshaft Pulley Parts Questions & Experts Answers

Crankshaft Pulley
2L7Z-6312-AA
Q: How to remove and install the crankshaft pulley and front crankshaft seal in V8 engine on Ford F-150?
A: To take out the crankshaft pulley, let pull out the cable from the negative terminal of the battery and set down that of the drive-belt. For 2010 and earlier models raise the vehicle properly on jackstands and take out the engine cooling fan and shroud assembly. Take off the crankshaft pulley center bolt with the socket and breaker bar; when doing this, make sure that the pulley is locked in position with a strap or the chain wrench and place a shop rag or a piece of drivebelt material around the crankshaft pulley. If there are holes provided on the pulley to thread in, then a bolt type puller should be used but where there are no holes, then the pulley should be pulled off using a three jawed puller. There is always the need for an adapter between the puller bolt and the crankshaft so as not to damage them. Third, employ a seal puller to remove the crankshaft front oil seal without scratching the crankshaft or damage the bore. Clean the crossland bore and check for nicks or gouges and also the hub zone for signs of abnormal wearing. As for the installation, there is a requirement of a new bolt for the 5.0L and 6.2L engines to reinstall the crankshaft pulley. Slather the external lip of the new seal with clean engine oil before forcing it into place with the use of a seal driver or a socket that is a little smaller than the seal while the 'open-end' must be facing the engine. Any contact surface of the crankshaft pulley hub with the oil seal must be smeared with multi-purpose grease or clean engine oil and the front end of the keyway in the crankshaft pulley must be treated with RTV sealant before assembling. Withdraw the crankshaft pulley with an especial installation tool without the need for a hammer and fasten the center bolt and torque it to the recommended value. The remaining steps are-again-the reverse order of removal steps.

Related Ford F-150 Parts

Browse by Year