How to remove and install Turn Signal Switch on a Lincoln Town Car?

Disconnect the cable from the negative battery terminal. For 1989 and earlier models, grasp the switch lever securely and remove it by pulling straight out. Remove the steering column covers. Remove the switch cover, then disconnect the connector, remove the retaining screws and withdraw the Turn Signal Switch assembly from the steering column. Place the switch in position and install the screws, then connect the electrical connector. Install the steering column covers. Line up the tangs on the lever with the slot in the switch and install it by pushing straight in. For 1990 and later models, remove the steering column covers. On most models, the ignition lock cylinder must be removed first, and on models with tilt-column steering, the tilt lever must also be removed before removing the covers. Remove the two retaining screws, pull the switch out, disconnect the connector and detach the Turn Signal Switch assembly from the steering column. Connect the electrical connector, insert the switch into the steering column and install the screws. Install the steering column covers, lock cylinder and tilt lever if equipped. For all models, connect the cable to the negative battery terminal.

How to replace the hazard and turn signal switches on Lincoln Town Car?

The hazard and turn signal switches on earlier models are part of the turn signal switch hub assembly while in later models they are integrated into the multi-function switch. Disconnect the battery cable to replace the turn signal and hazard switch. Lower the cover, and remove the steering wheel. At the harness connectors, disconnect the wires from the switches. Remove the hazard switch by lifting it after unscrewing a retaining screw. Unscrew a turn signal handle, lift out this switch after removing retaining screws. Pull wires through the hub, remove the plastic cover, remove the assembly. Insert new switch wires through the hub and connect them to the connector. For complete installation reverse removal steps.

Genuine Lincoln Town Car Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Turn Signal Switches found

View related parts
Lincoln Town Car Switch Assy - Direction Indicator
Part Number: 7W1Z-13K359-AA
$96.25 MSRP: $159.09
You Save: $62.84 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Combination Switch, Multifunction Switch
- Replaces: 5W1Z-13K359-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Lincoln Town Car | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R70W (AODE), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R70E W/TSS*S/V, 4-Speed Automatic Transmission AODEW/4R75E W/TSS S/V, 4-Speed Automatic Transmission NAAO AODEW/4R70W*S/VIL, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Town Car Switch Assy - Direction Indicator
Part Number: YW3Z-13K359-AB
$86.93 MSRP: $166.36
You Save: $79.43 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Combination Switch, Multifunction Switch
- Replaces: YW3Z-13K359-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2002 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Switch - Dir. Indic/Warning Flasher
Part Number: EOAZ-13341-A
$52.70 MSRP: $72.01
You Save: $19.31 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Turn Signal & Hazard Switch
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1982-1984 Lincoln Town Car | 8 Cyl 5.0L | 4AT AOD
View related parts
Lincoln Town Car Switch Assembly - Direction Indicator
Part Number: 3W1Z-13K359-BAA
$71.35 MSRP: $136.55
You Save: $65.20 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Direction Indicator
- Replaced by: 3W1Z-13K359-BAB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Switch Assembly - Direction Indicator
Part Number: YW3Z-13K359-AA
$86.93 MSRP: $166.36
You Save: $79.43 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Direction Indicator
- Replaced by: YW3Z-13K359-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000 Lincoln Town Car | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Lincoln Town Car Switch Assembly - Direction Indicator
Part Number: 5W1Z-13K359-AA
$96.25 MSRP: $159.09
You Save: $62.84 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assy - Direction Indicator
- Manufacturer Note: Multi Function Switch
- Replaced by: 7W1Z-13K359-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Lincoln Town Car | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R70W (AODE), 4-Speed Automatic Transmission 4R75E Livonia, 4-Speed Automatic Transmission AODEW/4R70E W/TSS, 4-Speed Automatic Transmission AODEW/4R70E W/TSS*S/V, 4-Speed Automatic Transmission AODEW/4R75E W/TSS S/V, 4-Speed Automatic Transmission NAAO AODEW/4R70W*S/VIL, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Lincoln Town Car Switch - Dir. Indic/Warning Flasher
Part Number: E7SZ-13341-A
Product Specifications
- Other Name: Turn Signal & Hazard Switch
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1985-1989 Lincoln Town Car | 8 Cyl 5.0L | 4AT AOD

Lincoln Town Car Turn Signal Switch

We provide a wide range of Lincoln Town Car Turn Signal Switch at the best prices possible. If you need Lincoln Town Car Turn Signal Switch, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Lincoln Town Car Turn Signal Switch Parts Questions & Experts Answers

Switch Assembly - Direction Indicator
YW3Z-13K359-AA
Q: How to remove and install Turn Signal Switch on a Lincoln Town Car?
A: Disconnect the cable from the negative battery terminal. For 1989 and earlier models, grasp the switch lever securely and remove it by pulling straight out. Remove the steering column covers. Remove the switch cover, then disconnect the connector, remove the retaining screws and withdraw the Turn Signal Switch assembly from the steering column. Place the switch in position and install the screws, then connect the electrical connector. Install the steering column covers. Line up the tangs on the lever with the slot in the switch and install it by pushing straight in. For 1990 and later models, remove the steering column covers. On most models, the Ignition Lock Cylinder must be removed first, and on models with tilt-column steering, the tilt lever must also be removed before removing the covers. Remove the two retaining screws, pull the switch out, disconnect the connector and detach the Turn Signal Switch assembly from the steering column. Connect the electrical connector, insert the switch into the steering column and install the screws. Install the steering column covers, lock cylinder and tilt lever if equipped. For all models, connect the cable to the negative battery terminal.
Switch Assy - Direction Indicator
YW3Z-13K359-AB
Q: How to replace the hazard and turn signal switches on Lincoln Town Car?
A: The hazard and turn signal switches on earlier models are part of the turn signal switch hub assembly while in later models they are integrated into the multi-function switch. Disconnect the battery cable to replace the turn signal and hazard switch. Lower the cover, and remove the steering wheel. At the harness connectors, disconnect the wires from the switches. Remove the hazard switch by lifting it after unscrewing a retaining screw. Unscrew a turn signal handle, lift out this switch after removing retaining screws. Pull wires through the hub, remove the plastic cover, remove the assembly. Insert new switch wires through the hub and connect them to the connector. For complete installation reverse removal steps.