How to remove and install a Fuel Pump on Mercury Mariner?

The fuel level sender can be separated from the fuel pump module and replaced on 2009 and later models. To do this, first relieve the residual pressure in the fuel system and equalize tank pressure by removing the fuel filler cap. Then, disconnect the cable from the negative battery terminal and fold the rear seat cushion forward if necessary. Remove the carpeting covering the fuel pump/fuel level sending unit module access cover, and then remove the access cover. Clean the surrounding area to prevent introducing water, dirt, and dust into the tank. Disconnect the fuel pump/fuel level sending unit module electrical connector and the fuel line connection(s) if applicable. Also disconnect the electrical connector for the fuel pressure sensor. Disconnect the fuel supply and return lines from the fuel pump/fuel level sending unit module, and soak up any spilled fuel with a rag. Unscrew the fuel pump/fuel level sending unit module retaining ring, and if necessary, use a hammer and a brass punch to loosen it. Carefully remove the fuel pump/fuel level sending unit module from the fuel tank, taking care not to bend the sending unit float arm. If only the fuel level sender needs to be replaced on 2009 and later models, disconnect its wiring harness from the fuel pump module, then depress the locking tabs and remove the sender. Before installing the pump, inspect the neoprene gasket for wear and damage, and replace it if necessary. Also inspect the fuel pump inlet filter at the base of the pump and clean it if dirty. Align the fuel pump/fuel level sending unit module with its hole in the tank and carefully insert it into the tank, making sure not to damage the float arm. The remainder of the installation is the reverse of removal. After reconnecting the battery, the Powertrain Control Module (PCM) must relearn its idle and fuel trim strategy for optimum driveability and performance.

How to check the fuel pump and fuel pressure in a Mercury Mariner?

The fuel pump is located inside the fuel tank, which muffles its sound when the engine is running. However, you can hear the fuel pump if you sit inside the vehicle with the windows closed, turn the ignition key to ON and listen carefully for the whirring sound made by the fuel pump as it's briefly turned on to pressurize the fuel system prior to starting the engine. If you can't hear the pump, remove the fuel filler cap, depress the spring-loaded door inside the fuel filler neck, then have an assistant turn the ignition switch to ON while you listen for the sound of the pump being primed.If the pump does not come on when the ignition key is turned to ON, check the fuel pump fuse and relay located in the engine compartment fuse and relay box. If these are okay, check the wiring back to the fuel pump. If the fuse, relay and wiring are okay, the fuel pump is probably defective. If the pump runs continuously with the ignition key in its ON position, the Powertrain Control Module (PCM) is probably defective and should be checked by a dealer service department or other qualified repair shop.To check the fuel pressure on a V6 engine, you'll need a fuel pressure gauge with an adapter that fits the Schrader valve on the left end of the fuel rail. Four cylinder engines do not have a Schrader valve, so you will need to obtain a fuel pressure gauge with which you can tee into the fuel system at a suitable fuel line fitting. To connect a fuel pressure gauge to the Schrader valve test port, first screw on the adapter, then hook up the fuel pressure gauge. On four-cylinder models, you'll have to tee into the fuel system at the connection between the fuel supply line and the fuel rail.Start the engine and allow it to idle. Note the gauge reading as soon as the pressure stabilizes, and compare it with the pressure listed in the specifications. If the pressure is lower than specified, check the fuel lines and hoses for kinks, blockages and leaks. Check the fuel strainer for restrictions. If all these components are okay, the fuel filter could be clogged or the fuel pump module could be defective. If the fuel pressure is higher than specified, replace the fuel pump module.Turn off the engine and verify that the fuel pressure stays at the specified level for five minutes after the engine is turned off. Then disconnect the fuel pressure gauge, making sure to cover the fitting with a rag before loosening it. Mop up any spilled gasoline. Start the engine and verify that there are no fuel leaks.

Genuine Mercury Mariner Fuel Pump

Gas Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Fuel Pumps found

View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: AL8Z-9H307-B
$284.49 MSRP: $474.55
You Save: $190.06 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: AL8Z-9H307-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Mariner | 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Fuel Pump And Sender Assembly
Part Number: AL8Z-9H307-A
$263.20 MSRP: $427.27
You Save: $164.07 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Mariner | 4 Cyl 2.5L Duratec (110kW/150PS) | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 7L8Z-9H307-B
$440.51 MSRP: $611.94
You Save: $171.43 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Replaces: 5L8Z-9H307-BD, 6L8Z-9H307-BA, 5L8Z-9H307-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 8L8Z-9H307-G
$248.60 MSRP: $400.00
You Save: $151.40 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Replaced by: 8L8Z-9H307-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 9M6Z-9H307-C
$248.60 MSRP: $400.00
You Save: $151.40 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Replaces: 9M6Z-9H307-A, 9M6Z-9H307-B, PFS-477
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Mariner | 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L PFI Gas/Electric | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: AM6Z-9H307-A
$258.77 MSRP: $416.36
You Save: $157.59 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Mariner | 4 Cyl 2.5L PFI Gas/Electric | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 9L8Z-9H307-C
$234.35 MSRP: $390.91
You Save: $156.56 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Replaces: 9L8Z-9H307-A, 9L8Z-9H307-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mercury Mariner | 4 Cyl 2.5L Duratec (110kW/150PS), 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 9L8Z-9H307-B
$234.35 MSRP: $390.91
You Save: $156.56 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 9L8Z-9H307-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Mariner | 4 Cyl 2.5L Duratec (110kW/150PS), 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 9L8Z-9H307-A
$234.35 MSRP: $390.91
You Save: $156.56 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 9L8Z-9H307-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Mariner | 4 Cyl 2.5L Duratec (110kW/150PS), 6 Cyl 3.0L OHC Duratec | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 8L8Z-9H307-D
$250.86 MSRP: $403.64
You Save: $152.78 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Replaced by: 8L8Z-9H307-J
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 8L8Z-9H307-C
$250.86 MSRP: $403.64
You Save: $152.78 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 8L8Z-9H307-J
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 9M6Z-9H307-B
$248.60 MSRP: $400.00
You Save: $151.40 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 9M6Z-9H307-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Mariner | 4 Cyl 2.5L PFI Gas/Electric | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 9M6Z-9H307-A
$248.60 MSRP: $400.00
You Save: $151.40 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 9M6Z-9H307-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Mariner | 4 Cyl 2.5L PFI Gas/Electric | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 8L8Z-9H307-F
$248.60 MSRP: $400.00
You Save: $151.40 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 8L8Z-9H307-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 8M6Z-9H307-A
$340.13 MSRP: $547.27
You Save: $207.14 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 8M6Z-9H307-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | 4 Cyl 2.3L Hybrid Gas/Electric DOHC | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 8M6Z-9H307-C
$340.13 MSRP: $547.27
You Save: $207.14 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy; Fuel Pump, Fuel Pump Assembly
- Replaced by: 8M6Z-9H307-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | 4 Cyl 2.3L Hybrid Gas/Electric DOHC | 4AT CD4E, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Fuel Pump And Sender Assembly
Part Number: 5M6Z-9H307-A
$495.04 MSRP: $803.64
You Save: $308.60 (39%)
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 7M6Z-9H307-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | 4 Cyl 2.3L Hybrid Gas/Electric DOHC | CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 5L8Z-9H307-A
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 7L8Z-9H307-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 5L8Z-9H307-BD
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 7L8Z-9H307-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
View related parts
Mercury Mariner Sender And Pump Assembly
Part Number: 6L8Z-9H307-BA
Product Specifications
- Other Name: Sender And Pump Assy
- Replaced by: 7L8Z-9H307-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Mariner | 4 Cyl 2.3L, 6 Cyl 3.0L DOHC EFI Modular | 4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)

| Page 1 of 2 |Next >

1-20 of 27 Results

Mercury Mariner Fuel Pump

Fuel Pump is one of the significant components of Mercury Mariner vehicles that help to provide the required amount of fuel to the engine to make successful combustion. It pumps the fuel from the tank to the carburetor or fuel injection mechanism, electric type of pumps being quite fashionable in fuel injection. Fuel pumps that are mechanically operated by the cam shaft feed fuel to the carburetors. Performance fuel pumps are flow rated in GPH or LPH, and there are several kinds to fit each horsepower level. The mechanical type has long been mounted in the engine block, but electric pumps are currently used since they can work as well at high pressure as their old mechanical counterparts. These pumps are controlled on safety and rational fuel rate by ECUs that enhance engine performances as well as minimized emission.

We provide a wide range of Mercury Mariner Fuel Pump at the best prices possible. If you need Mercury Mariner Fuel Pump, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Mercury Mariner Fuel Pump Parts Questions & Experts Answers

Sender And Pump Assembly
8L8Z-9H307-G
Q: How to remove and install a Fuel Pump on Mercury Mariner?
A: The fuel level sender can be separated from the fuel pump module and replaced on 2009 and later models. To do this, first relieve the residual pressure in the fuel system and equalize tank pressure by removing the fuel filler cap. Then, disconnect the cable from the negative battery terminal and fold the rear seat cushion forward if necessary. Remove the carpeting covering the fuel pump/fuel level sending unit module access cover, and then remove the access cover. Clean the surrounding area to prevent introducing water, dirt, and dust into the tank. Disconnect the fuel pump/fuel level sending unit module electrical connector and the fuel line connection(s) if applicable. Also disconnect the electrical connector for the fuel pressure sensor. Disconnect the fuel supply and return lines from the fuel pump/fuel level sending unit module, and soak up any spilled fuel with a rag. Unscrew the fuel pump/fuel level sending unit module retaining ring, and if necessary, use a hammer and a brass punch to loosen it. Carefully remove the fuel pump/fuel level sending unit module from the fuel tank, taking care not to bend the sending unit float arm. If only the fuel level sender needs to be replaced on 2009 and later models, disconnect its wiring harness from the fuel pump module, then depress the locking tabs and remove the sender. Before installing the pump, inspect the neoprene gasket for wear and damage, and replace it if necessary. Also inspect the fuel pump inlet filter at the base of the pump and clean it if dirty. Align the fuel pump/fuel level sending unit module with its hole in the tank and carefully insert it into the tank, making sure not to damage the float arm. The remainder of the installation is the reverse of removal. After reconnecting the battery, the Powertrain Control Module (PCM) must relearn its idle and fuel trim strategy for optimum driveability and performance.
Fuel Pump And Sender Assembly
AL8Z-9H307-A
Q: How to check the fuel pump and fuel pressure in a Mercury Mariner?
A: The fuel pump is located inside the fuel tank, which muffles its sound when the engine is running. However, you can hear the fuel pump if you sit inside the vehicle with the windows closed, turn the ignition key to ON and listen carefully for the whirring sound made by the fuel pump as it's briefly turned on to pressurize the fuel system prior to starting the engine. If you can't hear the pump, remove the fuel filler cap, depress the spring-loaded door inside the fuel filler neck, then have an assistant turn the ignition switch to ON while you listen for the sound of the pump being primed.If the pump does not come on when the ignition key is turned to ON, check the fuel pump fuse and relay located in the engine compartment fuse and relay box. If these are okay, check the wiring back to the fuel pump. If the fuse, relay and wiring are okay, the fuel pump is probably defective. If the pump runs continuously with the ignition key in its ON position, the Powertrain Control Module (PCM) is probably defective and should be checked by a dealer service department or other qualified repair shop.To check the fuel pressure on a V6 engine, you'll need a fuel pressure gauge with an adapter that fits the Schrader valve on the left end of the Fuel Rail. Four cylinder engines do not have a Schrader valve, so you will need to obtain a fuel pressure gauge with which you can tee into the fuel system at a suitable fuel line fitting. To connect a fuel pressure gauge to the Schrader valve test port, first screw on the adapter, then hook up the fuel pressure gauge. On four-cylinder models, you'll have to tee into the fuel system at the connection between the fuel supply line and the fuel rail.Start the engine and allow it to idle. Note the gauge reading as soon as the pressure stabilizes, and compare it with the pressure listed in the specifications. If the pressure is lower than specified, check the fuel lines and hoses for kinks, blockages and leaks. Check the fuel strainer for restrictions. If all these components are okay, the fuel filter could be clogged or the fuel pump module could be defective. If the fuel pressure is higher than specified, replace the fuel pump module.Turn off the engine and verify that the fuel pressure stays at the specified level for five minutes after the engine is turned off. Then disconnect the fuel pressure gauge, making sure to cover the fitting with a rag before loosening it. Mop up any spilled gasoline. Start the engine and verify that there are no fuel leaks.

Related Mercury Mariner Parts

Browse by Year

2011 Fuel Pump 2010 Fuel Pump 2009 Fuel Pump 2008 Fuel Pump 2007 Fuel Pump 2006 Fuel Pump 2005 Fuel Pump