Lincoln F1AZ-6731-A Filter Assembly - Oil

You can Select Your Vehicle to check if F1AZ-6731-A fits your vehicle.

For preventive maintenance, regular oil changes are essential. Aging engine oil will become diluted and contaminated, leading to premature engine wear. This is because replacing the oil filter with each change has low costs and easy installation. Find the oil drain plug and filter without hitting hot exhaust parts. Return to running condition after starting it, let the engine warm up, and park it on flat ground which turns it off again. Make sure the car is safely raised; then put a glove on while removing the plug and place the pan below it. Ensure all of the oil has been drained out completely while checking for metal particles as well. Once dry, reinstall the plug as well as move the pan beneath the filter. At this point, apply some lubricant to the gasket of the new filter after tightening it with your hand, and then lower the car down. Add five quarts of fresh oil into it, check the level through the dipstick before finally starting the engine for a short time.

Engine oils degrade with use and become dilute; hence it is desirable to change them frequently and that this is an effective method of preventive maintenance. In this business, you ought to make sure you have a set of all instruments vital for the project and many rags in anticipation of a stain. Start with engine at normal operating temperature; this produces better flow of oils and sludges. After warming the vehicle turn off the engine, find a level and flat ground and take off the oil filler cap. The oil drain plug and filter is more easily accessible if the vehicle is on a hoist or jack stands; always avoid working under a vehicle that is only on a jack. Carry the jack under the engine in the manner to avoid the hot exhaust parts and find the drain plug and the oil filter. Place a drain pan underneath the plug, clear the area, and when removing the plug take keen on hot oil. When the oil has been drained, look into the oil for metallic debris, and check the drain plug for deposits, clean it and bolt it tightly back in its position. After that, place the drain pan beneath the oil filter, and using a filter wrench, remove this unit; in case the filter is quite tight, it is possible to use a metal bar for its turning. When already opened, twist and remove the cap while in an angle to avoid spilling of the contents. While putting on the filter, remove all the old gasket from the mounting surface on the block and examine the used filter to the new one. Apply a little engine oil on the gasket of the new filter then fit it into position and tighten it in the right manner. When all the tools and materials are taken out, lower down the vehicle and put in fresh oil through the filler cap with the help of a funnel and put in four quarts and pouring the dipstick. Cranks the engine and check for drips at the drain plug and filter and if there are some then using the spanner tighten them. Check the oil level again after some few minutes and add more if the quantity is low. The first few times when you are on the road after a modification, your primary observations should be the leakage and the level of oil. Last but not the least collect and dispose off the used oil that cannot be reclaimed by pouring it into container for possible disposal.

Maintenance for prevention requires frequent oil changes. Collect rags and tools in the event of spillage. While cars are on ramps, filters and drain plugs can be reached. Begin the engine up, let it warm up fully, then park it on a level surface. Lift the car with stands and put the pan below the plug. Remove the oil, check for metallic particles, and clean up its plug as well as opening filter surfaces. Fit a new filter lubricating its gasket then filling it with new oil. Check the dipstick level and watch out for any drips. You may have to drop off used oil at a reclamation center or recycling facility.

After draining the old oil, inspect it for metal particles, wipe the drain plug, reinstall it securely, and move the drain pan under the oil filter.

Move the drain pan under the oil filter and loosen the filter using a filter wrench. If the filter is too tight, puncture it with a metal bar or long screwdriver to loosen it. Unscrew the filter from the block, being careful to prevent oil from spilling out.

Yes, some late-model vehicles allow oil change intervals to be adjusted through the instrument panel's display function. The default setting is typically 7,500 miles but can be changed if needed.

Yes, some late-model vehicles allow oil change intervals to be adjusted through the instrument panel's display function. The default setting is typically 7,500 miles but can be changed if needed.