Mercury BXT-65-750 Battery

You can Select Your Vehicle to check if BXT-65-750 fits your vehicle.

To disconnect the battery, start by disconnecting both cables from the battery terminals. It is important to use a battery terminal puller if necessary and always disconnect the negative cable first and hook it up last to avoid shorting the battery. Next, loosen the two battery hold-down clamp nuts to disengage the hold-down legs from the battery tray and remove the hold-down clamp as an assembly. Lift out the battery, using special straps or clamps if available to make the process easier. To install the battery, simply reverse the removal steps. Ensure that the battery cables and battery posts are free of corrosion and clean or replace them if necessary.

First of all, a regular preventive maintenance program is needed to enable quick and reliable starts of your vehicle's battery. Whenever you are not driving, switch off the engine and accessories as well as disconnect the negative terminal and keep sparks and flames away from the battery. Also, the battery produces flammable hydrogen gas and contains corrosive sulfuric acid, so handle it with care and wear protective glasses. Look for corrosion, cracks, loose connections, clean clamps using warm water or baking soda. Ensure that you check if there are any signs of damage on the terminals before putting them back into place. Use a slow-rate charger to restore a discharged battery following instructions provided.

A battery must be near a full charge to test it accurately. First, disconnect the negative battery cable. Visually inspect the indicator eye on the battery, if available. Charge the battery if the indicator is dark. If the battery has removable caps, check the electrolyte level; it should be above the plates. Use distilled water if the level is low, but avoid overfilling. For a precise measurement, use a battery hydrometer to draw and test the electrolyte's specific gravity, ensuring it's approximately 1.270 at 68 degrees F (20 degrees C). If the specific gravity is low, charge the battery. Next, use a digital voltmeter for an open circuit voltage test. The battery should display over 12.5 volts; if not, charge it. For the battery load test, use a load tester from auto parts stores. Install the tester onto the battery terminals and follow the manufacturer's guidelines, ensuring the voltage doesn't drop below 9.6 volts during a 15-second load. Cold temperatures might lower the voltage requirements, so adjust accordingly. For the battery drain test, ensure all accessories are off and connect a digital ammeter between the negative cable and post. A drain of up to 100 milliamps is normal, but 500 milliamps or more suggests a problem. If an issue arises, identify the problematic circuit by removing fuses one by one.For replacement, begin by disconnecting the negative battery cable(s). On single battery systems, detach the negative cable from the battery post and keep it isolated. On dual battery systems, start with the auxiliary battery's negative cable and then the main battery's negative cable, ensuring they remain isolated. Remove the positive cable from its post next. Then, unfasten the battery hold-down clamp bolts. Lift out the battery with caution due to its weight. Battery handlers or straps are recommended for assistance. Check the battery tray for corrosion and clean it with a baking soda-water mixture if needed, then dry thoroughly. If replacing the battery, ensure the new one matches the original in specifications. When reinstalling, align the battery foot's center notch with the tray's cut-out, secure the hold-down clamp nuts without overtightening. Reconnect the cables and coat the connections with petroleum jelly or grease to prevent corrosion.

To maintain reliable starts, you must maintain your vehicle's battery. Safety should come first with necessary equipment and disconnecting cables before servicing the battery. Check for corrosion, loose connections, or cracks. Cable clamps and terminals must be cleaned using warm water together with a baking soda solution. Finally, rinse as well as making sure that the battery tray and hold-down clamp bolts are ok. Slow charging is a better option to restore deeply discharged batteries or during winter periods. Use a trickle charger where necessary for maximum safety. Pay attention to fast boost chargers too. Follow the instructions on the charger very strictly concerning charging times especially.

Sealed batteries eliminate the need for electrolyte checks and water additions, making maintenance simpler.

Loosen the cable end bolt and disconnect the cable from the negative battery terminal. Then, isolate the cable end to prevent it from coming into accidental contact with the battery terminal.

When examining the battery's external condition, you should check for damage, corrosion, loose connections, cracks, and the condition of hold-down clamps.

Disconnect any electrical harness or connectors from the battery tray.

Start by removing both cables from the battery terminals. Use a wrench or battery pliers if necessary.

Wash all areas with plain water.

Start by disconnecting both cables from the battery terminals.

Sealed batteries eliminate the need for electrolyte checks and water additions, making maintenance simpler.

Clean or replace them if necessary.

Disconnecting the negative cable first helps to avoid shorting the battery.

Safety and having the appropriate equipment at hand.

First, remove the bolt and wedge from the battery tray. Then, lift out the battery. Be cautious as it is heavy, and consider using special lifting straps for easier handling.

If corrosion is evident on the battery terminals, the battery should be removed for cleaning.

Replace it with a battery that has identical dimensions, amperage rating, cold cranking rating, etc.

Before any battery maintenance, ensure the engine and all accessories are turned off, and disconnect the cables from the negative battery terminal to minimize risks.