Make sure this part fits

Mercury YL8Z-3B414-BA Joint And Stub Shaft Assy

2005-2006 Mercury Mariner YL8Z3B414BA

Customer Questions & Expert Answers (3)
Ford YL8Z-3B414-BA Joint And Stub Shaft Assy
  • Part Description
    Joint And Stub Shaft Assy
  • Base No.
    3B414B
  • Position
    Passenger Side And Driver Side Inner
  • Manufacturer
    Ford
Make sure this part fits
$96.86 MSRP: $132.34
You Save: $35.48 (27%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Mercury
    Base No.3B414B
    Manufacturer Part NumberYL8Z-3B414-BA, YL8Z3B414BA
    Part DescriptionJoint And Stub Shaft Assy
    Other NamesInner CV Joint
    Manufacturer NoteRH And LH Inner
    Item Dimensions28.8 x 4.9 x 6.6 inches
    Item Weight4.60 Pounds
    PositionPassenger Side And Driver Side Inner
    ConditionNew
    Fitment TypeDirect Replacement
    Require Quantity2
    ManufacturerFord
    SKUYL8Z-3B414-BA
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2005-2006 Mercury Mariner5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
  • Customer Questions & Expert Answers

    Q:
    Will these fit my car and if not which part will? Thank you. Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if YL8Z-3B414-BA fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    What are the steps to install the rear driveaxle for the 2010 Mercury Mariner? Posted by Customer
    A:
    To install the rear driveaxle in 2004 and earlier models, follow these steps:a) Pry the old spring clip from the inner end of the driveaxle and install a new one.b) Apply a light film of grease to the area on the inner CV joint stub shaft where the seal rides, then insert the splined end of the inner CV joint into the differential.c) Make sure the spring clip locks in its groove.d) Apply a light film of grease to the outer CV joint splines, pry the trailing arm outward, and insert the outer end of the driveaxle into the hub.e) Install the coil spring.f) Connect the trailing arm to the lower suspension arm and install the nut.g) Using a floor jack, raise the trailing arm to simulate normal ride height and then tighten the nut.h) Install a new driveaxle/hub nut and tighten it before lowering the vehicle to prevent wheel bearing damage.i) Install the wheel and lug nuts, then lower the vehicle and tighten the lug nuts.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What are the steps to install the rear driveaxle in the 2003 Ford Escape? Posted by Customer
    A:
    To install the rear driveaxle in 2004 and earlier models, follow these steps: a) Pry the old spring clip from the inner end of the driveaxle and install a new one. b) Apply a light film of grease to the area on the inner CV joint stub shaft where the seal rides, then insert the splined end of the inner CV joint into the differential. c) Make sure the spring clip locks in its groove. d) Apply a light film of grease to the outer CV joint splines, pry the trailing arm outward, and insert the outer end of the driveaxle into the hub. e) Install the coil spring. f) Connect the trailing arm to the lower suspension arm and install the nut. g) Using a floor jack, raise the trailing arm to simulate normal ride height and then tighten the nut. h) Install a new driveaxle/hub nut and tighten it before lowering the vehicle to prevent wheel bearing damage. i) Install the wheel and lug nuts, then lower the vehicle and tighten the lug nuts. j) Block the front wheels to keep the vehicle from rolling. k) Loosen the rear wheel lug nuts, raise the vehicle on jackstands, then remove the wheel. l) Remove the rear wheel driveaxle hub nut and discard it. m) Remove the coil spring. n) Remove the wheel speed sensor wiring harness mounting bolt. o) Remove the four bolts from the stabilizer bar bracket and discard them. p) Place a floor jack under the knuckle and support it. q) Remove the bolt from the lower ball joint, then separate the ball joint from the knuckle. r) Separate the inner and outer ends of the driveaxle from the differential and the hub. Work carefully to avoid damaging the CV joints and boots. s) Installation is the reverse of removal.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part YL8Z-3B414-BA, the Right Choice

To ensure reliability, purchase Ford part # YL8Z-3B414-BA Joint And Stub Shaft Assy. It is sometimes referred to as Mercury Axle Shaft. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Mercury Mariner models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford YL8Z3B414BA Joint And Stub Shaft Assy. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Mercury parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly