×
Contact Us Live Chat or 1-888-788-9341
My Garage
My Account
Cart
Search Bar
Search by Part Number, Part Name, or Vehicle
Track Order Help Center
Make sure this part fits

Mercury XR3Z-6108-HA Piston And Pin Assembly

1998-2006 Mercury Grand Marquis XR3Z6108HA

Customer Questions & Expert Answers (10)
Ford XR3Z-6108-HA Piston And Pin Assembly
Ford XR3Z-6108-HA Piston And Pin Assembly
  • Part Description
    Piston And Pin Assy
  • Replaced By
    2C5Z-6108-AB
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers

  • Related Parts

    Shop for related parts for your vehicle

  • Product Specifications

    BrandGenuine Mercury
    Manufacturer Part NumberXR3Z-6108-HA, XR3Z6108HA
    Part DescriptionPiston And Pin Assy
    Item Weight1.10 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerFord
    SKUXR3Z-6108-HA
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65

  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1998-2006 Mercury Grand Marquis8 Cyl 4.6L4AT 4R70W

  • Customer Questions & Expert Answers

    Q:
    Is the the correct part for the attached VIN? Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if XR3Z-6108-HA fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after tightening the nuts on the rod cap for the 2001 Lincoln Town Car? Posted by Customer
    A:
    Scrape off any traces of Plastigage if the oil clearance is correct - Apply a layer of clean moly-base grease or engine assembly lube to the bearing faces - Slide the connecting rod back into place on the journal.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Piston
    Q:
    How should you secure the cap nuts for the 1994 Lincoln Town Car? Posted by Customer
    A:
    You should secure the cap nuts finger tight.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Piston
    Q:
    What should be measured for the piston rings for the 1992 Lincoln Town Car? Posted by Customer
    A:
    Measure piston ring side clearance and piston-to-bore clearance, replacing pistons if needed.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Piston
    Q:
    What should be done to ensure the ring compressor is properly seated for the 2010 Mercury Grand Marquis? Posted by Customer
    A:
    Tap the top edge of the ring compressor to make sure it's contacting the block around its entire circumference.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after removing the carbon deposits for the 2002 Mercury Grand Marquis? Posted by Customer
    A:
    Clean the piston/rod assemblies with solvent and dry them with compressed air (if available). Make sure the oil return holes in the back sides of the ring grooves are clear.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done if the endplay exceeds the service limit for the 2005 Mercury Grand Marquis? Posted by Customer
    A:
    If the endplay exceeds the service limit, new connecting rods will be required. If new rods or a new crankshaft are installed, the endplay may fall under the specified minimum. If it does, the rods will have to be machined to restore it. Consult an automotive machine shop for advice if necessary. Repeat the procedure for the remaining connecting rods.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Piston
    Q:
    What should be done after all piston/connecting rod assemblies are installed for the 1992 Ford Crown Victoria? Posted by Customer
    A:
    Rotate the crankshaft a number of times by hand to check for any obvious binding.
    Posted by FordPartsGiant Specialist
    Q:
    What must be done before the inspection process can be carried out for the 2008 Ford Crown Victoria? Posted by Customer
    A:
    The piston/connecting rod assemblies must be cleaned and the original piston rings removed from the pistons. Note: Always use new piston rings when the engine is reassembled.
    Posted by FordPartsGiant Specialist
    Q:
    What is the next step after removing the cylinder ridges for the 2005 Ford Crown Victoria? Posted by Customer
    A:
    After the cylinder ridges have been removed, turn the engine upside-down so the crankshaft is facing up.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Piston
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part XR3Z-6108-HA, the Right Choice

To ensure reliability, purchase Ford part # XR3Z-6108-HA Piston And Pin Assembly. It is sometimes referred to as Mercury Piston. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Mercury Grand Marquis models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford XR3Z6108HA Piston And Pin Assembly. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Mercury parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly