Make sure this part fits

Mercury 5L8Z-3A428-DB Front Axle Shaft

2005-2011 Mercury Mariner 5L8Z3A428DB

Customer Questions & Expert Answers (3)
Ford 5L8Z-3A428-DB Front Axle Shaft
  • Part Description
    Shaft - Front Axle
  • Base No.
    3B436
  • Position
    Passenger Side
  • Replaces
    5L8Z-3A428-DA, YL8Z-3A428-CA, YL8Z-3A428-DA, TX-318
  • Manufacturer
    Ford
Make sure this part fits
$86.35 MSRP: $165.27
You Save: $78.92 (48%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Mercury
    Base No.3B436
    Manufacturer Part Number5L8Z-3A428-DB, 5L8Z3A428DB
    Part DescriptionShaft - Front Axle
    Other NamesAxle Assembly
    Item Dimensions28.0 x 4.8 x 4.8 inches
    Item Weight14.20 Pounds
    PositionPassenger Side
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces5L8Z-3A428-DA, YL8Z-3A428-CA, YL8Z-3A428-DA, TX-318
    ManufacturerFord
    SKU5L8Z-3A428-DB
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2005-2011 Mercury Mariner4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L DOHC EFI Modular, 6 Cyl 3.0L OHC Duratec4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, 6-Speed Automatic Transmission 6F Mid-Range, CVT Auto Trans Powersplit Elec, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Right Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
  • Customer Questions & Expert Answers

    Q:
    Will these fit my car and if not which part will? Thank you. Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 5L8Z-3A428-DB fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    What are the steps for installing the front driveaxle for the 2007 Mercury Mariner? Posted by Customer
    A:
    To install the front driveaxle, follow these steps:a) Pry the old spring clip from the inner end of the driveaxle (left side) or outer end of the intermediate shaft (right side) and install a new one.b) Lubricate the differential or intermediate shaft seal with multipurpose grease and raise the driveaxle into position while supporting the CV joints.c) Push the splined end of the inner CV joint into the differential side gear (left side) or onto the intermediate shaft (right side) and make sure the spring clip locks in its groove.d) Apply a light coat of multipurpose grease to the outer CV joint splines, pull out on the steering knuckle assembly, and install the stub axle into the hub.e) Insert the ball joint stud into the steering knuckle and tighten the pinch bolt.f) Install a new driveaxle/hub nut and tighten it before lowering the vehicle to prevent wheel bearing damage.g) Grasp the inner CV joint housing (not the driveaxle) and pull out to ensure the driveaxle has seated securely in the transaxle or on the intermediate shaft.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    How do you remove the front driveaxle in the 2008 Ford Escape? Posted by Customer
    A:
    To remove the front driveaxle, follow these steps: a) Loosen the wheel lug nuts and raise the vehicle on jackstands. b) Remove the wheel and the driveaxle/hub nut from the axle, then separate the lower control arm from the steering knuckle. c) Swing the knuckle/hub assembly out until the end of the driveaxle is free of the hub. If the driveaxle splines stick in the hub, tap on the end of the driveaxle with a plastic hammer. d) Support the outer end of the driveaxle with a piece of wire to avoid unnecessary strain on the inner CV joint. e) If removing the right driveaxle, carefully pry the inner CV joint off the intermediate shaft using a large screwdriver or prybar. If removing the left driveaxle, pry the inner CV joint out of the transaxle using a large screwdriver or prybar, being careful not to damage the differential seal. f) Support the CV joints and carefully remove the driveaxle from the vehicle.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part 5L8Z-3A428-DB, the Right Choice

To ensure reliability, purchase Ford part # 5L8Z-3A428-DB Front Axle Shaft. It is sometimes referred to as Mercury Axle Shaft, Mercury CV Joint. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Mercury Mariner models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford 5L8Z3A428DB Front Axle Shaft. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Mercury parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly