Make sure this part fits

Mercury 5L8Z-3A329-B Shaft

2005-2008 Mercury Mariner 5L8Z3A329B

Customer Questions & Expert Answers (3)
Ford 5L8Z-3A329-B Shaft
  • Part Description
    Shaft
  • Base No.
    3B414A
  • Replaces
    YL8Z-3A329-DB
  • Manufacturer
    Ford
Make sure this part fits
$135.60 MSRP: $188.33
You Save: $52.73 (28%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Mercury
    Base No.3B414A
    Manufacturer Part Number5L8Z-3A329-B, 5L8Z3A329B
    Part DescriptionShaft
    Other NamesIntermed Shaft, Intermediate Shaft
    Item Dimensions4.9 x 5.1 x 21.7 inches
    Item Weight7.70 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ReplacesYL8Z-3A329-DB
    ManufacturerFord
    SKU5L8Z-3A329-B
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2005-2008 Mercury Mariner4 Cyl 2.3L, 4 Cyl 2.3L Hybrid Gas/Electric DOHC, 6 Cyl 3.0L DOHC EFI Modular4AT CD4E, 5-Speed Manual Transmission, 5-Speed Manual Transmission - AK, Front-Wheel Drive (Left Hand Drive), Left Hand Drive, Two-Wheel Drive (Left Hand Drive), Two-Wheel Drive (Right Hand Drive)
  • Customer Questions & Expert Answers

    Q:
    Will these fit my car and if not which part will? Thank you. Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 5L8Z-3A329-B fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    What are the steps to install the rear driveaxle in the 2010 Ford Escape? Posted by Customer
    A:
    To install the rear driveaxle in 2004 and earlier models, follow these steps: a) Pry the old spring clip from the inner end of the driveaxle and install a new one. b) Apply a light film of grease to the area on the inner CV joint stub shaft where the seal rides, then insert the splined end of the inner CV joint into the differential. c) Make sure the spring clip locks in its groove. d) Apply a light film of grease to the outer CV joint splines, pry the trailing arm outward, and insert the outer end of the driveaxle into the hub. e) Install the coil spring. f) Connect the trailing arm to the lower suspension arm and install the nut. g) Using a floor jack, raise the trailing arm to simulate normal ride height and then tighten the nut. h) Install a new driveaxle/hub nut and tighten it before lowering the vehicle to prevent wheel bearing damage. i) Install the wheel and lug nuts, then lower the vehicle and tighten the lug nuts. j) Block the front wheels to keep the vehicle from rolling. k) Loosen the rear wheel lug nuts, raise the vehicle on jackstands, then remove the wheel. l) Remove the rear wheel driveaxle hub nut and discard it. m) Remove the coil spring. n) Remove the wheel speed sensor wiring harness mounting bolt. o) Remove the four bolts from the stabilizer bar bracket and discard them. p) Place a floor jack under the knuckle and support it. q) Remove the bolt from the lower ball joint, then separate the ball joint from the knuckle. r) Separate the inner and outer ends of the driveaxle from the differential and the hub. Work carefully to avoid damaging the CV joints and boots. s) Installation is the reverse of removal.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What are the steps for installing the front driveaxle for the 2008 Mercury Mariner? Posted by Customer
    A:
    To install the front driveaxle, follow these steps:a) Pry the old spring clip from the inner end of the driveaxle (left side) or outer end of the intermediate shaft (right side) and install a new one.b) Lubricate the differential or intermediate shaft seal with multipurpose grease and raise the driveaxle into position while supporting the CV joints.c) Push the splined end of the inner CV joint into the differential side gear (left side) or onto the intermediate shaft (right side) and make sure the spring clip locks in its groove.d) Apply a light coat of multipurpose grease to the outer CV joint splines, pull out on the steering knuckle assembly, and install the stub axle into the hub.e) Insert the ball joint stud into the steering knuckle and tighten the pinch bolt.f) Install a new driveaxle/hub nut and tighten it before lowering the vehicle to prevent wheel bearing damage.g) Grasp the inner CV joint housing (not the driveaxle) and pull out to ensure the driveaxle has seated securely in the transaxle or on the intermediate shaft.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part 5L8Z-3A329-B, the Right Choice

Your vehicle deserves only genuine OEM Ford parts and accessories. To ensure reliability, purchase Ford part # 5L8Z-3A329-B Shaft with base parts number 3B414A. It is sometimes referred to as Mercury Axle Shaft. Our Ford parts and accessories are expedited directly from authorized Ford dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM Ford parts are the best for restoring your vehicle to factory condition performance. This part fits specific Mercury Mariner models.

Affordable, reliable and built to last, Ford part # 5L8Z3A329B Shaft stands out as the smart option. FordPartsGiant.com is your prime online source with the biggest and best selection of genuine Ford parts and accessories at giant discounted prices. We have the OEM Ford parts and accessories you need at the wholesale prices. FordPartsGiant.com has you covered no matter what type of Ford vehicle you drive. For detailed Mercury parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly