How to remove the headlight switch on Ford Bronco?

For early models, start by disconnecting the cable from the negative battery terminal. Next, remove the knob on the switch by reaching under the dash and pressing the shaft lock tab while pulling the knob and shaft away from the cluster panel. Then, take off the steering column shroud and remove the screws securing the top of the instrument cluster finish panel to the dash before taking off the finish panel. Unscrew the headlight switch mounting nut, remove the switch from the panel, and disconnect the wiring connector from the switch. Installation follows the reverse order of removal, without needing to push the knob lock tabs when reinstalling. For later models, begin by disconnecting the cable from the negative battery terminal. Unsnap the right and left moldings by carefully prying at the notches on the bottom. Use a hooked tool to remove the headlight knob by depressing the spring inside it, then remove the exposed screws under the moldings. Unsnap the instrument cluster finish panel by starting at the lower clips and then the upper clips, disconnect the wiring attached to the finish panel, and remove the panel. Remove the switch pushrod by inserting a punch or similar tool into the switch access hole while pulling the rod from the switch. Unscrew the switch molding nut and pull the switch out through the rear of the dash, disconnect the switch wiring harness, and remove the switch. Installation is the reverse of removal.

Genuine Ford Bronco Headlight Switch

Headlamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Headlight Switches found

View related parts
Ford Bronco SWITCH ASY - HEADLAMPS
Part Number: M2DZ-11654-GC
$22.34 MSRP: $32.67
You Save: $10.33 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Headlamp Switch
- Replaces: M2DZ-11654-GB, M2DZ-11654-GA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Bronco | 4 Cyl 2.3 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Bronco SWITCH ASY - HEADLAMPS
Part Number: M2DZ-11654-HC
$27.03 MSRP: $42.00
You Save: $14.97 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Headlamp Switch
- Replaces: M2DZ-11654-HA, M2DZ-11654-HB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Bronco | 4 Cyl 2.3 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Bronco SWITCH ASY - HEADLAMPS
Part Number: M2DZ-11654-DC
$71.82 MSRP: $114.55
You Save: $42.73 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Headlamp Switch
- Replaces: M2DZ-11654-DA, M2DZ-11654-DB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Bronco | 4 Cyl 2.3 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Bronco SWITCH ASY - HEADLAMPS
Part Number: M2DZ-11654-AC
$23.05 MSRP: $35.82
You Save: $12.77 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Headlamp Switch
- Replaces: M2DZ-11654-AB, M2DZ-11654-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford Bronco | 4 Cyl 2.3 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Bronco Switch Assembly
Part Number: E7TZ-11654-B
Product Specifications
- Other Name: Switch Assy
- Replaced by: 6C2Z-11654-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT A4LD, 4AT AOD, 4AT E4OD, 4MT, 5MT
- 1987-1989 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4MT, 5MT
View related parts
Ford Bronco Switch Assembly
Part Number: E1TZ-11654-A
Product Specifications
- Other Name: Switch Assy; Headlamp Switch
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1981-1986 Ford Bronco | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L | 3AT C6, 4AT AOD, 4MT

Ford Bronco Headlight Switch

The Headlight Switch is an important component of safety of Ford Bronco cars as it allows to use the headlights. This switch does both the functions of turning the headlights on and off but also allows the adjusting of intensity of the beam making it useful when driving under different conditions. For years, various types of Headlight Switch have been used on the Ford Bronco car since they also underwent changes in design and use. The principle objectives may still be the same, but the procedures and services provided may differ from time to time, to address the continually dynamic needs of drivers. The Ford Bronco's Headlight Switch is very important for the lighting system of the car, thus, play a significant role in safety on the roads.

We provide a wide range of Ford Bronco Headlight Switch at the best prices possible. If you need Ford Bronco Headlight Switch, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Bronco Headlight Switch Parts Questions & Experts Answers

Switch Assembly
E1TZ-11654-A
Q: How to remove the headlight switch on Ford Bronco?
A: For early models, start by disconnecting the cable from the negative battery terminal. Next, remove the knob on the switch by reaching under the dash and pressing the shaft lock tab while pulling the knob and shaft away from the cluster panel. Then, take off the steering column shroud and remove the screws securing the top of the instrument cluster finish panel to the dash before taking off the finish panel. Unscrew the headlight switch mounting nut, remove the switch from the panel, and disconnect the wiring connector from the switch. Installation follows the reverse order of removal, without needing to push the knob lock tabs when reinstalling. For later models, begin by disconnecting the cable from the negative battery terminal. Unsnap the right and left moldings by carefully prying at the notches on the bottom. Use a hooked tool to remove the headlight knob by depressing the spring inside it, then remove the exposed screws under the moldings. Unsnap the instrument cluster finish panel by starting at the lower clips and then the upper clips, disconnect the wiring attached to the finish panel, and remove the panel. Remove the switch pushrod by inserting a punch or similar tool into the switch access hole while pulling the rod from the switch. Unscrew the switch molding nut and pull the switch out through the rear of the dash, disconnect the switch wiring harness, and remove the switch. Installation is the reverse of removal.