How do you remove sealed beam headlights on Ford Bronco II?

If one wants to remove sealed beam headlights, one can begin by loosening the screws on the retaining ring and then removing the ring. The front side of the headlight bulb should be slid out so that it can be disconnected from the cable assembly plug. On the other hand, one can install a new light bulb by joining the wiring assembly connector with a new bulb and carefully pushing it in its place. Retaining screws are used to attach the retaining ring in place after which the headlight trim is put back into position using screws. On the other hand, for composite-type headlights open the hood, and lower bulb access cover. Remove the locking ring and pull the bulb and wire harness plug assembly out. Cut the electrical wire harness plug free from the locking ring then remove it. To install a new bulb just need to clean contact surfaces, pass the locking ring over the lamp ends, and locate it in position on the lens door.

Genuine Ford Bronco II Headlight

Headlamp

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Headlights found

View related parts
Ford Bronco II Bulb - Tungsten
Part Number: F3UZ-13007-A
$32.15 MSRP: $47.00
You Save: $14.85 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Headlamp, Lamp, Sealed Beam
- Position: Passenger Side
- Replaces: E1FZ-13007-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1988 Ford Bronco II | 4 Cyl 2.3L, 6 Cyl 2.8L, 6 Cyl 2.9L | 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Bronco II Bulb - Tungsten
Part Number: E9TZ-13007-D
$77.93 MSRP: $106.49
You Save: $28.56 (27%)
ADD TO CART
Product Specifications
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989-1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 4MT, 5MT
View related parts
Ford Bronco II Headlamp Assembly
Part Number: F1TZ-13008-D
Product Specifications
- Other Name: Headlamp Assy; Composite Assembly, Composite Headlamp
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4MT, 5MT
View related parts
Ford Bronco II Lamp Assembly
Part Number: E9TZ-13007-C
Product Specifications
- Other Name: Lamp Assy
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989-1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 4MT, 5MT
View related parts
Ford Bronco II Headlamp Assembly
Part Number: E9TZ-13008-J
Product Specifications
- Other Name: HEADLAMP ASY
- Manufacturer Note: R.H., Complete asy.
- Position: Passenger Side
- Replaced by: F1TZ-13008-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Bronco II Headlamp Assembly
Part Number: F1TZ-13008-G
Product Specifications
- Other Name: Headlamp Assy
- Manufacturer Note: R.H. Complete assy., R.H.
- Position: Passenger Side
- Replaced by: F1TZ-13008-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989 Ford Bronco II | 6 Cyl 2.9L | 4AT A4LD, 4MT, 5MT

Ford Bronco II Headlight Parts Questions & Experts Answers

Headlamp Assembly
F1TZ-13008-D
Q: How do you remove sealed beam headlights on Ford Bronco II?
A: If one wants to remove sealed beam headlights, one can begin by loosening the screws on the retaining ring and then removing the ring. The front side of the headlight bulb should be slid out so that it can be disconnected from the cable assembly plug. On the other hand, one can install a new light bulb by joining the wiring assembly connector with a new bulb and carefully pushing it in its place. Retaining screws are used to attach the retaining ring in place after which the headlight trim is put back into position using screws. On the other hand, for composite-type headlights open the hood, and lower bulb access cover. Remove the locking ring and pull the bulb and wire harness plug assembly out. Cut the electrical wire harness plug free from the locking ring then remove it. To install a new bulb just need to clean contact surfaces, pass the locking ring over the lamp ends, and locate it in position on the lens door.