How to inspect and replace brake line and rubber brake hoses on Ford Crown Victoria?

About every six months, the rubber hoses which connect the steel brake lines with the front and rear brake assemblies should be inspected for cracks, chafing of the outer cover, leaks, blisters and other damage. These are important and vulnerable parts of the brake system and inspection should be complete. A light and mirror will be helpful for a thorough check. If a hose exhibits any of the above conditions, replace it with a new one. Using a flare nut wrench, disconnect the brake line from the hose fitting, being careful not to bend the frame bracket or brake line. Hold the fitting on the hose with a wrench to prevent the metal line from twisting and the frame bracket from bending. Remove the large retaining clip and detach the hose from the bracket and the body. Remove the banjo bolt from the caliper and discard the sealing washers. Connect the hose to the caliper, using new sealing washers. Tighten the banjo bolt. Without twisting the hose, connect the other end of the line to the bracket on the chassis. Connect the metal brake line to the hose fitting by hand, then, using a flare nut wrench, tighten the fitting securely. Be sure to use a wrench on the hose fitting to prevent the bracket from bending or the metal line from twisting. When the brake hose installation is complete, there should be no kinks in the hose. Make sure the hose doesn't contact any part of the suspension. Check this by turning the wheels to the extreme left and right positions. If the hose makes contact, remove it and correct the installation as necessary. When replacing brake lines be sure to use the correct parts. Don't use copper tubing for any brake system components. Purchase steel brake lines from a dealer or auto parts store. Prefabricated brake line, with the tube ends already flared and fittings installed, is available at auto parts stores and dealers. These lines are also sometimes bent to the proper shapes. When installing the new line make sure it's securely supported in the brackets and has plenty of clearance between moving or hot components. After installation, check the master cylinder fluid level and add fluid as necessary. Bleed the brake system and test the brakes carefully before driving the vehicle in traffic.

Genuine Ford Crown Victoria Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

47 Brake Lines found

View related parts
Ford Crown Victoria Hose Assembly
Part Number: 6W1Z-2A442-AA
$27.44 MSRP: $38.12
You Save: $10.68 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Rear Brake Hose
Part Number: F2AZ-2A442-A
$53.99 MSRP: $73.76
You Save: $19.77 (27%)
ADD TO CART
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Brake Hose Assembly
Part Number: 1W7Z-2078-BA
$36.78 MSRP: $50.26
You Save: $13.48 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hose, Flex Hose
- Manufacturer Note: LH, With ABS - with or without Traction Control
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Brake Hose Assembly
Part Number: 1W7Z-2078-AA
$51.42 MSRP: $70.26
You Save: $18.84 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hose, Flex Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Rear Brake-Hydraulic Hose
Part Number: 1W7Z-2A442-BA
$24.95 MSRP: $34.09
You Save: $9.14 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Hose Assembly
Part Number: 1W7Z-2A442-CA
$32.62 MSRP: $44.58
You Save: $11.96 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Manufacturer Note: RH , With or without Traction Control , Less special purpose vehicle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Hose Assembly
Part Number: 1W7Z-2A442-AA
$26.79 MSRP: $36.61
You Save: $9.82 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Hose Assembly
Part Number: F2AZ-2A442-B
$67.01 MSRP: $93.09
You Save: $26.08 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Manufacturer Note: LH, without ABS
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Brand Left Left Side Front Brake Hose
Part Number: 3W1Z-2078-BA
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hose, Flex Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Hose Assembly
Part Number: 3W1Z-2A442-AA
Product Specifications
- Other Name: Brake Hose, Flex Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Hose Assembly
Part Number: 3W1Z-2A442-BA
Product Specifications
- Other Name: Hose Assy; Brake Hose, Flex Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Brake Pipe
Part Number: F6AZ-2A040-BB
$0.00
Product Specifications
- Other Name: Pipe - Brake
- Manufacturer Note: w/ ABS & TC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Brake Tube Assembly
Part Number: F7AZ-2B253-AA
$0.00
Product Specifications
- Other Name: Tube Assembly - Brake
- Manufacturer Note: w/anti-spin traction brakes
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Brake Tube Assembly
Part Number: 9W7Z-2267-C
$16.78 MSRP: $26.07
You Save: $9.29 (36%)
Product Specifications
- Other Name: Tube Assembly - Brake
- Replaces: 6W1Z-2267-B, 6W1Z-2267-A, 9W7Z-2267-B, 9W7Z-2267-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, 4AT, 4AT 4R75W, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Brake Hose Assembly
Part Number: 1W7Z-2078-CA
Product Specifications
- Other Name: Hose Assy - Brake; Brake Hose, Flex Hose
- Manufacturer Note: LH , Less ABS
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Tube Assembly Brake
Part Number: 2W7Z2263BA
Product Specifications
- Other Name: Tube Assy - Brake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Brake Tube Assembly
Part Number: 3W1Z-2267-AA
Product Specifications
- Other Name: Tube Assembly - Brake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Brake Tube Assembly
Part Number: 3W1Z-2C296-AA
Product Specifications
- Other Name: Tube Assembly - Brake; Brake Tube
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Brake Tube Assembly
Part Number: 3W1Z-2C296-BA
Product Specifications
- Other Name: Tube Assembly - Brake; Brake Tube
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Brake Tube Assembly
Part Number: 3W7Z-2C287-AA
Product Specifications
- Other Name: Tube Assembly - Brake
- Manufacturer Note: Less Livery/long wheelbase package
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W

| Page 1 of 3 |Next >

1-20 of 47 Results

Ford Crown Victoria Brake Line

Brake Line in Ford Crown Victoria is the component that used to facilitate the brake fluid from the master cylinder to the brake caliper pistons so that the hydraulic brake system can work. The metal brake systems include brake line which may rust, or get damaged by shock and /or vibration thereby causing leakage of the brake fluid and reduced hydraulic pressure. It is worth noticing that brake hoses can also become physically and internally damaged, which will compromise the brake performance. In cases that they need replacement, DOT3 preformed brake line kits and stainless steel flexible hose, corrosion free are offered for simple application. There is a considerable improvement of the feel of the pedal when the braided stainless steel hoses are fitted as opposed to situations that require performance driving abilities.

We provide a wide range of Ford Crown Victoria Brake Line at the best prices possible. If you need Ford Crown Victoria Brake Line, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Crown Victoria Brake Line Parts Questions & Experts Answers

Brake Hose Assembly
3W1Z-2078-AA
Q: How to inspect and replace brake line and rubber brake hoses on Ford Crown Victoria?
A: About every six months, the rubber hoses which connect the steel brake lines with the front and rear brake assemblies should be inspected for cracks, chafing of the outer cover, leaks, blisters and other damage. These are important and vulnerable parts of the brake system and inspection should be complete. A light and mirror will be helpful for a thorough check. If a hose exhibits any of the above conditions, replace it with a new one. Using a flare nut wrench, disconnect the brake line from the hose fitting, being careful not to bend the frame bracket or brake line. Hold the fitting on the hose with a wrench to prevent the metal line from twisting and the frame bracket from bending. Remove the large retaining clip and detach the hose from the bracket and the body. Remove the banjo bolt from the caliper and discard the sealing washers. Connect the hose to the caliper, using new sealing washers. Tighten the banjo bolt. Without twisting the hose, connect the other end of the line to the bracket on the chassis. Connect the metal brake line to the hose fitting by hand, then, using a flare nut wrench, tighten the fitting securely. Be sure to use a wrench on the hose fitting to prevent the bracket from bending or the metal line from twisting. When the brake hose installation is complete, there should be no kinks in the hose. Make sure the hose doesn't contact any part of the suspension. Check this by turning the wheels to the extreme left and right positions. If the hose makes contact, remove it and correct the installation as necessary. When replacing brake lines be sure to use the correct parts. Don't use copper tubing for any brake system components. Purchase steel brake lines from a dealer or auto parts store. Prefabricated brake line, with the tube ends already flared and fittings installed, is available at auto parts stores and dealers. These lines are also sometimes bent to the proper shapes. When installing the new line make sure it's securely supported in the brackets and has plenty of clearance between moving or hot components. After installation, check the master cylinder fluid level and add fluid as necessary. Bleed the brake system and test the brakes carefully before driving the vehicle in traffic.