Should servicing of valves, valve seats, and valve guides be done by a professional on Ford Crown Victoria?

Because of the nature of the position and the specific instruments and equipment needed, performing the valve job as it takes to service the valves, valve seats, and valve guides should be handled by an expert. An amateur can unbolt the head, open it to inspection and semi-cleaning before delivering the assembly to a dealership or an automotive machine where the actual work will be done. It makes it possible to determine the state of components of heads and valve trains, know what work is still required, what new parts may be needed when cooperating with an automotive machine shop. The dealer service department or automotive machine shop is retained for the relief of valves and springs, valve face necessary reconditioning or new, reconditioning of valve guides, checking and replacing of valve springs, spring retainers, rotators and keepers if necessary, valve seal replacement, assembly of valve components, and correct installed spring height check also. Also, if its surface has warping, the cylinder head gasket surface will be resurfaced. After the valve job is done by a professional the head will be almost as new as it was when it first came out the factory. On its arrival, the head must also be washed to reduce the amount of metal particles and abrasive grit that might still be present after serving the valves or resurfacing, and compressed air if available should be used to blow out all the oil holes and passages before fitting on the engine.

Genuine Ford Crown Victoria Exhaust Valve

Exhaust Muffler Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Exhaust Valves found

View related parts
Ford Crown Victoria Valve - Exhaust
Part Number: XL3Z-6505-AA
$41.18 MSRP: $75.00
You Save: $33.82 (46%)
ADD TO CART
Product Specifications
- Other Name: Exhaust Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
- 2001-2005 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W
View related parts
Ford Crown Victoria Valve - Exhaust
Part Number: F1AZ-6505-A
$16.71 MSRP: $22.84
You Save: $6.13 (27%)
ADD TO CART
Product Specifications
- Other Name: Exhaust Valve, Valve
- Replaces: F75Z-6505-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-2000 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Valve - Exhaust
Part Number: F6AZ-6505-AB
$31.92 MSRP: $43.61
You Save: $11.69 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2002 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W
View related parts
Ford Crown Victoria Valve - Exhaust
Part Number: 6W7Z-6505-BA
$43.21 MSRP: $63.17
You Save: $19.96 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve
- Manufacturer Note: STD.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Crown Victoria | 8 Cyl 4.6L, 8 Cyl 4.6L Romeo SOHC EFI | 4AT, 4AT 4R75W, 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Valve - Exhaust
Part Number: XL3Z-6505-EA
Product Specifications
- Manufacturer Note: Std., Natural Gas only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Ford Crown Victoria | 8 Cyl 4.6L | 4AT, 4AT 4R70W, 4AT 4R75W

Ford Crown Victoria Exhaust Valve

Exhaust Valve is one of the main components in internal combustion engine and in Ford Crown Victoria its function is to let out or expel the burnt exhaust gases from the engine cylinders. This process is critically important in ensuring that the engine attains its premier working condition since the damage to the Exhaust Valve could cause some complications that are, loss in power, failures in engine to fire, rough idle, and deteriorating fuel economy. In the Ford Crown Victoria models there is appointed a certain process for operating the Exhaust Valves, aimed at proper ejection of exhaust gases. Although the quoted information does not point to the fact as to whether there exist Exhaust Valves of one kind or the other or that different style of Exhaust Valves is installed in different Crown Victoria, it emphasizes on the efficiency of Exhaust Valves in avoiding such issues resulting from the Crown Victoria engines.

We provide a wide range of Ford Crown Victoria Exhaust Valve at the best prices possible. If you need Ford Crown Victoria Exhaust Valve, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Crown Victoria Exhaust Valve Parts Questions & Experts Answers

Valve - Exhaust
F6AZ-6505-AB
Q: Should servicing of valves, valve seats, and valve guides be done by a professional on Ford Crown Victoria?
A: Because of the nature of the position and the specific instruments and equipment needed, performing the valve job as it takes to service the valves, valve seats, and valve guides should be handled by an expert. An amateur can unbolt the head, open it to inspection and semi-cleaning before delivering the assembly to a dealership or an automotive machine where the actual work will be done. It makes it possible to determine the state of components of heads and valve trains, know what work is still required, what new parts may be needed when cooperating with an automotive machine shop. The dealer service department or automotive machine shop is retained for the relief of valves and springs, valve face necessary reconditioning or new, reconditioning of valve guides, checking and replacing of valve springs, spring retainers, rotators and keepers if necessary, valve seal replacement, assembly of valve components, and correct installed spring height check also. Also, if its surface has warping, the cylinder head gasket surface will be resurfaced. After the valve job is done by a professional the head will be almost as new as it was when it first came out the factory. On its arrival, the head must also be washed to reduce the amount of metal particles and abrasive grit that might still be present after serving the valves or resurfacing, and compressed air if available should be used to blow out all the oil holes and passages before fitting on the engine.