How to check and replace the fuel level sending unit in a Ford Crown Victoria?

Raise the vehicle and support it securely on jackstands. Disconnect the electrical connector for the fuel level sensor. Note: On 1998 and earlier models, disconnect the electrical connector at the pump. On 1999 and later models, the electrical connector is located in the harness and must be disconnected at the electrical connector away from the tank. Position the ohmmeter probes into the electrical connector and check the resistance. Use the 200-ohm scale on the ohmmeter. With the fuel tank completely full, the resistance should be about 170.0 ohms. With the fuel tank nearly empty, the resistance of the sensor should be about 11.0 ohms. If the readings are incorrect, replace the sensor. A more accurate check of the sensor can be made by removing it from the fuel tank and checking its resistance while manually operating the float arm. Remove the fuel pump/sensor assembly from the vehicle. Carefully angle the sensor out of the opening without damaging the fuel level float located at the bottom of the assembly. Remove the sensor electrical connector from the fuel pump assembly. Remove the screws that secure the sensor to the fuel pump assembly. Installation is the reverse of removal. If the float arm and float wire loop were damaged or bent during removal and installation, adjust the angle and travel distance. Be sure to install a new rubber gasket.

Genuine Ford Crown Victoria Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Fuel Level Sensors found

View related parts
Ford Crown Victoria Fuel Tank Sender Assembly
Part Number: 6W1Z-9A299-A
$70.64 MSRP: $140.36
You Save: $69.72 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Fuel Tank Sender Assembly
Part Number: 2W1Z-9275-AB
$73.07 MSRP: $116.55
You Save: $43.48 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank
- Replaces: 2W1Z-9275-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Crown Victoria | 8 Cyl 4.6L Romeo SOHC EFI | 4-Speed Automatic Transmission 4R75E Livonia, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Crown Victoria Fuel Tank Sender Assembly
Part Number: F2AZ-9275-B
Product Specifications
- Other Name: Sender Assembly - Fuel Tank ; Fuel Gauge Sending Unit; Fuel Gauge Sending Unit, Sending Unit
- Manufacturer Note: MECHANICAL INSTR. CLUSTER
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Fuel Tank Sender Assembly
Part Number: F3AZ-9275-B
Product Specifications
- Other Name: Sender Assembly - Fuel Tank ; Fuel Gauge Sending Unit; Fuel Gauge Sending Unit, Sending Unit
- Manufacturer Note: MECHANICAL INSTR. CLUSTER
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD-E
View related parts
Ford Crown Victoria Fuel Tank Sender Assembly
Part Number: F3AZ-9275-E
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Gauge Sending Unit, Sending Unit
- Manufacturer Note: MECHANICAL INSTR. CLUSTER
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD, 4AT AOD-E
View related parts
Ford Crown Victoria Fuel Tank Sender Assembly
Part Number: F3AZ-9275-G
Product Specifications
- Other Name: Sender Assembly - Fuel Tank
- Manufacturer Note: Electronic instr. cluster, FROM 1/94
- Replaced by: F3VY-9275-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994 Ford Crown Victoria | 8 Cyl 4.6L | 4AT AOD-E
View related parts
Ford Crown Victoria Sender Assembly
Part Number: F5AZ-9275-A
Product Specifications
- Other Name: Sender Assy; Fuel Gauge Sending Unit, Sending Unit
- Manufacturer Note: exc. Mexico
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Crown Victoria | 8 Cyl 4.6L | 4AT 4R70W, 4AT AOD-E

Ford Crown Victoria Fuel Level Sensor

Fuel Level Sensor in Ford Crown Victoria vehicle is an important unit to indicate the fuel level in the tank to the driver. These electronic devices are specifically created to give precise data on the extent of fuel with respect to temperatures and the data is delivered almost instantly. Made up of a float, actuating rod, and resistor, the fuel sensor transmits information regarding the fuel level to the fuel gauze so that the driver is notified of the need to refill. In the case of any fault, regarding the fuel level sensor, it is advisable to consult professional Auto mechanics to avoid holding a full fuel tank indication after refueling.

We provide a wide range of Ford Crown Victoria Fuel Level Sensor at the best prices possible. If you need Ford Crown Victoria Fuel Level Sensor, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Crown Victoria Fuel Level Sensor Parts Questions & Experts Answers

Fuel Tank Sender Assembly
6W1Z-9A299-A
Q: How to check and replace the fuel level sending unit in a Ford Crown Victoria?
A: Raise the vehicle and support it securely on jackstands. Disconnect the electrical connector for the fuel level sensor. Note: On 1998 and earlier models, disconnect the electrical connector at the pump. On 1999 and later models, the electrical connector is located in the harness and must be disconnected at the electrical connector away from the tank. Position the ohmmeter probes into the electrical connector and check the resistance. Use the 200-ohm scale on the ohmmeter. With the Fuel Tank completely full, the resistance should be about 170.0 ohms. With the fuel tank nearly empty, the resistance of the sensor should be about 11.0 ohms. If the readings are incorrect, replace the sensor. A more accurate check of the sensor can be made by removing it from the fuel tank and checking its resistance while manually operating the float arm. Remove the Fuel Pump/sensor assembly from the vehicle. Carefully angle the sensor out of the opening without damaging the fuel level float located at the bottom of the assembly. Remove the sensor electrical connector from the fuel pump assembly. Remove the screws that secure the sensor to the fuel pump assembly. Installation is the reverse of removal. If the float arm and float wire loop were damaged or bent during removal and installation, adjust the angle and travel distance. Be sure to install a new rubber gasket.