How to replace the IAT sensors in a Ford Fusion?

There are two Intake Manifold Temperature Sensor used, the Intake Manifold Temperature Sensor is located on the air filter housing outlet and the Intake Manifold Temperature Sensor is located on the turbocharger air outlet pipe. Disconnect the cable from the negative terminal of the battery. Lift the engine cover up and off of the ballstuds, then remove the cover. Disconnect the electrical connector from the Intake Manifold Temperature Sensor. Remove the sensor by turning it counter clockwise and pulling it out of the air outlet duct. Installation is the reverse of removal.

How to remove and install the MAF/IAT sensor and air intake duct on Ford Fusion?

To remove the Mass Air Flow (MAF)/Intake Manifold Temperature (IMT) start by removing the air intake duct and disconnecting the electrical connector from the MAF/IMT sensor. Remove the MAF/IMT sensor mounting fasteners and remove the sensor from the air filter housing. Installation is the reverse of removal.

Genuine Ford Fusion Intake Manifold Temperature Sensor

Air Intake Temperature Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Intake Manifold Temperature Sensors found

View related parts
Ford Fusion Sensor Assembly
Part Number: DS7Z-12A697-A
$12.64 MSRP: $19.64
You Save: $7.00 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2020 Ford Fusion | 4 Cyl 1.5 L GAS, 4 Cyl 1.5L GTDI, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS), 4 Cyl 2.5 L GAS, 6 Cyl 2.7L | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Sensor Assembly
Part Number: 9C1Z-12A697-D
$45.12 MSRP: $70.73
You Save: $25.61 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assy; Air Intake Temperature Sensor, Temperature Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2020 Ford Fusion | 4 Cyl 1.5 L GAS, 4 Cyl 1.5L GTDI, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transmission - B6, ECVT Auto Trans Power Split, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive

Ford Fusion Intake Manifold Temperature Sensor

The Intake Manifold Temperature Sensor that is installed in Ford Fusion vehicles is used in regulating the levels of air-fuel mixture that is required to achieve optimal combustion levels. It is combined with the Mass Air Flow (MAF) sensor that measures the air demanded in by the engine and sends this details to the Powertrain Control Module (PCM). The PCM then increases or decreases the fuel injector timing, and this helps in the complete burning of fuel. In the course of their manufacturing, there has been the use of numerous types of Intake Manifold Temperature Sensors on the Fusion, all serving to improve performance based on various environmental conditions. Although the types of sensors are not distinguished, some variations can be in the calibration, and compatibility with bolt-on performance parts such as air intake. lmt is extremely crucial to the efficiency of the vehicle and its failure like in the Intake Manifold Temperature Sensor can cause performance problems, poor acceleration and incorrect air to fuel rations.

We provide a wide range of Ford Fusion Intake Manifold Temperature Sensor at the best prices possible. If you need Ford Fusion Intake Manifold Temperature Sensor, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Fusion Intake Manifold Temperature Sensor Parts Questions & Experts Answers

Sensor Assembly
9C1Z-12A697-D
Q: How to replace the IAT sensors in a Ford Fusion?
A: There are two Intake Manifold Temperature Sensor used, the Intake Manifold Temperature Sensor is located on the air filter housing outlet and the Intake Manifold Temperature Sensor is located on the turbocharger air outlet pipe. Disconnect the cable from the negative terminal of the battery. Lift the engine cover up and off of the ballstuds, then remove the cover. Disconnect the electrical connector from the Intake Manifold Temperature Sensor. Remove the sensor by turning it counter clockwise and pulling it out of the air outlet duct. Installation is the reverse of removal.
Sensor Assembly
DS7Z-12A697-A
Q: How to remove and install the MAF/IAT sensor and air intake duct on Ford Fusion?
A: To remove the Mass Air Flow (MAF)/Intake Manifold Temperature (IMT) start by removing the air intake duct and disconnecting the electrical connector from the MAF/IMT sensor. Remove the MAF/IMT sensor mounting fasteners and remove the sensor from the air filter housing. Installation is the reverse of removal.