How to remove Clutch Disc and Pressure Plate on Ford Fusion?

The location of the components requires that clutch access be done by pulling off the transaxle but keeping the engine on the car. If the engine is being removed for major over haul, then it is good practice to inspect the clutch and replace any of them that requires replacement because the cost of replacing them is very cheap compared to other parts and since the engine or transaxle is already removed it would be cheaper to replace them were they are in bad condition unless they are new or in good condition. The first step is to have the transaxle disconnected, and to have the weight of the engine suspended through the use of a fixture or hoist. The clutch fork and release bearing could be retained on the transaxle housing. During the clutch disc removal you need clutch alignment tool through the disc hub to support the clutch disc. Look for index marks on flywheel and the pressure plate that would align the parts as they are reconnected in an assembly the lack of such marks means that you need to standardize your own so that you will align them properly when you reconnect them the next time. Reduce the pressure plate to the flywheel by a turns, then gradually take the bolts, the pressure plate and the clutch disc. Check all parts paying special attention on the flywheel for any crack or defects and also ensure that the clutch disc has adequate thickness of lining above the rivet head. The release bearing should be replaced together with the clutch disc due the intensity of their usage. Ensure that the pressure plate is worn or damaged and replace, if it is the case. Wear and damage of the pilot bearing should be checked and replaced if necessary. During installation, it will be necessary to lubricate a new pilot bearing, and then it is installed by hammering that is followed by thorough cleaning of the flywheel and pressure plate related surface. Set the clutch disc and pressure plate on the engine at the right orientation where they will be installed. Do not fully tighten the pressure plate to the flywheel bolts, only do it until they are hand tight, then using an alignment tool, center the clutch disc and then fully tighten the bolts in sock screw fashion to the torque specified. Grease the release bearing and fit it into position, followed by the transaxle and any and all other parts which may have been removed.

Genuine Ford Fusion Pressure Plate

Clutch Pressure Plate

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Pressure Plates found

View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: 9L8Z-7B066-C
$18.92 MSRP: $27.67
You Save: $8.75 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 1.6L PI TC ETHNL, 4 Cyl 2.0L Duratec Hybrid (130kW) , 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) , 4 Cyl 2.5L Duratec HE PFI, 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 2.7L, 6 Cyl 3.0L OHC Duratec, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: CV6Z-7B066-A
$27.02 MSRP: $39.50
You Save: $12.48 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 9L8Z-7B066-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 1.6L PI TC ETHNL, 4 Cyl 2.0L Duratec Hybrid (130kW), 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS), 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS), 4 Cyl 2.5L Duratec HE PFI, 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 2.7L, 6 Cyl 3.0L OHC Duratec, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: 9L8Z-7B066-D
$9.32 MSRP: $13.28
You Save: $3.96 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: Forward Clutch Pressure Plate
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6F Mid-Range, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
- 2010-2015 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 1.6L PI TC ETHNL, 4 Cyl 2.0L Duratec Hybrid (130kW), 4 Cyl 2.0L EcoBoost (240PS), 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS), 4 Cyl 2.5L Duratec HE PFI, 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L OHC Duratec, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: F2GZ-7B066-A
$11.45 MSRP: $16.32
You Save: $4.87 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: Forward Clutch Pressure Plate
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: 7T4Z-7B066-C
$17.56 MSRP: $25.67
You Save: $8.11 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 2.0L Duratec Hybrid (130kW) , 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) , 6 Cyl 2.7L | 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: 9L8Z-7B066-B
$27.02 MSRP: $39.50
You Save: $12.48 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: CV6Z-7B066-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | 4 Cyl 2.5L Duratec HE PFI, 4 Cyl 2.5L PFI Gas/Electric, 6 Cyl 3.0L OHC Duratec, 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: 7T4Z-7B066-A
$5.32 MSRP: $7.58
You Save: $2.26 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 2.0L Duratec Hybrid (130kW) , 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) , 6 Cyl 2.7L | 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate - Clutch Pressure
Part Number: DT4Z-7B066-A
$23.63 MSRP: $33.67
You Save: $10.04 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | 4 Cyl 1.5L GTDI, 4 Cyl 2.0L Duratec Hybrid (130kW) , 4 Cyl 2.0L EcoBoost (200PS), 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.5L Duratec (110kW/150PS), 4 Cyl 2.5L Duratec FFV (125kW/170PS) , 6 Cyl 2.7L | 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate Assembly - Clutch Pressure
Part Number: 6E5Z-7563-A
Product Specifications
- Other Name: Plate Assy - Clutch Pressure
- Replaced by: 7E5Z-7B546-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Fusion | 4 Cyl 2.3L | 5-Speed Manual Transmission (G5M), 6-Speed Manual Transmission Mazda G6M, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Fusion Plate Assembly - Clutch Pressure
Part Number: 7E5Z-7563-A
Product Specifications
- Other Name: Plate Assy - Clutch Pressure
- Replaced by: 7E5Z-7B546-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Fusion | 4 Cyl 2.3L | 5-Speed Manual Transmission (G5M), 6-Speed Manual Transmission Mazda G6M, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive

Ford Fusion Pressure Plate

We provide a wide range of Ford Fusion Pressure Plate at the best prices possible. If you need Ford Fusion Pressure Plate, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Fusion Pressure Plate Parts Questions & Experts Answers

Plate - Clutch Pressure
9L8Z-7B066-C
Q: How to remove Clutch Disc and Pressure Plate on Ford Fusion?
A: The location of the components requires that clutch access be done by pulling off the transaxle but keeping the engine on the car. If the engine is being removed for major over haul, then it is good practice to inspect the clutch and replace any of them that requires replacement because the cost of replacing them is very cheap compared to other parts and since the engine or transaxle is already removed it would be cheaper to replace them were they are in bad condition unless they are new or in good condition. The first step is to have the transaxle disconnected, and to have the weight of the engine suspended through the use of a fixture or hoist. The Clutch Fork and Release Bearing could be retained on the transaxle housing. During the clutch disc removal you need clutch alignment tool through the disc hub to support the clutch disc. Look for index marks on flywheel and the pressure plate that would align the parts as they are reconnected in an assembly the lack of such marks means that you need to standardize your own so that you will align them properly when you reconnect them the next time. Reduce the pressure plate to the flywheel by a turns, then gradually take the bolts, the pressure plate and the clutch disc. Check all parts paying special attention on the flywheel for any crack or defects and also ensure that the clutch disc has adequate thickness of lining above the rivet head. The release bearing should be replaced together with the clutch disc due the intensity of their usage. Ensure that the pressure plate is worn or damaged and replace, if it is the case. Wear and damage of the pilot bearing should be checked and replaced if necessary. During installation, it will be necessary to lubricate a new pilot bearing, and then it is installed by hammering that is followed by thorough cleaning of the flywheel and pressure plate related surface. Set the clutch disc and pressure plate on the engine at the right orientation where they will be installed. Do not fully tighten the pressure plate to the flywheel bolts, only do it until they are hand tight, then using an alignment tool, center the clutch disc and then fully tighten the bolts in sock screw fashion to the torque specified. Grease the release bearing and fit it into position, followed by the transaxle and any and all other parts which may have been removed.

Related Ford Fusion Parts

Browse by Year

2019 Pressure Plate 2018 Pressure Plate 2017 Pressure Plate 2016 Pressure Plate 2015 Pressure Plate 2014 Pressure Plate 2013 Pressure Plate 2012 Pressure Plate 2011 Pressure Plate 2010 Pressure Plate 2009 Pressure Plate 2008 Pressure Plate 2007 Pressure Plate 2006 Pressure Plate