How to check and adjust valve clearances after replace camshafts or valve-related parts on Ford Mustang?

It is important to check the valve clearances with the help of a cold engine. It is recommended that the valve clearances be checked and altered only after the camshaft(s) or any other related valve parts have been replaced, or when there is much rumbling noise in the valve-train. Start from disconnecting the cable that is connected to the negative terminal of the battery next is remove the spark plugs and the valve covers. Position the engine with the crankshaft pulley center bolt on the cylinder to be checked until cam lobes are out of the lifters as possible using socket and breaker bar. Gauge the clearance of each valve with a feeler gauge of the specified thickness; slight drag on the feeler gauge will tell that the clearance is correct. Record any valve which is out of specification as this will form part of the analysis when estimating the number of required replacement lifters. Again we shall repeat the same process for all the valves. Any of the clearance that exist must be adjusted by replacing the lifter with a new lifter whose thickness head is of a different measure. Stoke the lifters to be replaced and record their assorted valves. Head thickness of each lifter is to be measured using the micrometer on the center projection on the underside for accuracy. To calculate the correct thickness for a replacement lifter that will achieve the specified valve clearance, use the formula: A new lifter thickness would therefore be calculated as: N equal R + (M1-M2) These lifters are stamped on the bottom to show their size such a code 3.310 means the thickness is 3.31mm or 0.13 inch. This lifters are then marked according to their installation location, then applied with engine assembly lube and finally installed. To rectify the problem replace the lifters, reset the camshafts and timing chains and after that adjust the valve clearances.

Genuine Ford Mustang Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Intake Valves found

View related parts
Ford Mustang Valve - Inlet
Part Number: BR3Z-6507-A
$11.10 MSRP: $11.40
You Save: $0.30 (3%)
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Mustang | 8 Cyl 5.0L MOD DOHC SEFI NA | 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission (T56), 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: 2L2Z-6507-AA
$62.95 MSRP: $114.67
You Save: $51.72 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2010 Ford Mustang | 6 Cyl 4.0L SOHC EFI | 5-Speed Automatic Transmission 5R55S, 5-Speed Manual Transmission T5OD, 5-Speed Manual Transmission TR3650, 6-Speed Manual Transmission (T56), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: 7T4Z-6507-B
$12.65 MSRP: $18.50
You Save: $5.85 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2019 Ford Mustang | 6 Cyl 3.7L PFI NA | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission (T56), 6-Speed Manual Transmission-3160, 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: FR3Z-6507-A
$13.11 MSRP: $19.00
You Save: $5.89 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Mustang | 8 Cyl 5.0L MOD DOHC SEFI NA | 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission-3160, 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: 3L3Z-6507-BA
$8.44 MSRP: $12.02
You Save: $3.58 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Manufacturer Note: INSERT, VLV ST INTK
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2010 Ford Mustang | 8 Cyl 4.6L SOHC EFI, 8 Cyl 5.8L DOHC SC | 5-Speed Automatic Transmission 5R55S, 5-Speed Manual Transmission T5OD, 5-Speed Manual Transmission TR3650, 6-Speed Manual Transmission (T56), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: 1S7Z-6507-B
$12.29 MSRP: $17.50
You Save: $5.21 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Manufacturer Note: Intake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2023 Ford Mustang | 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission-3160, 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: JL3Z-6507-A
$7.90 MSRP: $11.25
You Save: $3.35 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2023 Ford Mustang | 8 Cyl 5.0 L GAS, 8 Cyl 5.0L DOHC EFI Modular, 8 Cyl 5.0L MOD DOHC SEFI NA | 10-Speed Automatic Transmission (10R80), 6-Speed Manual Transmission-3160, 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: 4G7Z-6507-AA
$36.08 MSRP: $51.83
You Save: $15.75 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2014 Ford Mustang | 8 Cyl 4.6L SOHC EFI, 8 Cyl 5.4L DOHC EFI S/C ALUM, 8 Cyl 5.8L DOHC SC | 5-Speed Automatic Transmission 5R55S, 5-Speed Manual Transmission T5OD, 5-Speed Manual Transmission TR3650, 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission (T56), 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: GR3Z-6507-A
$26.68 MSRP: $38.00
You Save: $11.32 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: GR3Z-6507-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2019 Ford Mustang | 8 Cyl 5.2L | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission-3160, 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: XL3Z-6507-AA
$38.80 MSRP: $70.67
You Save: $31.87 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2004 Ford Mustang | 8 Cyl 4.6L, 8 Cyl 4.6L SOHC EFI | 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R70W (AODE), 5MT, 5-Speed Manual Transmission (T450D), 5-Speed Manual Transmission T5OD, 5-Speed Manual Transmission TR3650, 6-Speed Manual Transmission Tremec T56, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: E3ZZ-6507-A
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1987-1995 Ford Mustang | 4 Cyl 2.3L, 8 Cyl 5.0L | 4AT A4LD, 4AT AOD, 4AT AOD-E, 5MT
- 1982-1985 Ford Mustang | 4 Cyl 2.3L, 6 Cyl 3.3L, 6 Cyl 3.8L, 8 Cyl 4.2L, 8 Cyl 5.0L | 3AT C3, 3AT C5, 4AT AOD, 4MT, 5MT
View related parts
Ford Mustang VALVE-INTAKE STD
Part Number: E5ZZ6507D
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1989 Ford Mustang | 4 Cyl 2.3L, 6 Cyl 3.3L, 6 Cyl 3.8L, 8 Cyl 4.2L, 8 Cyl 5.0L | 3AT C3, 3AT C4, 3AT C5, 4AT A4LD, 4AT AOD, 4MT, 5MT
View related parts
Ford Mustang Valve - Inlet
Part Number: F3LY-6507-A
$23.48 MSRP: $34.33
You Save: $10.85 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2004 Ford Mustang | 8 Cyl 4.6L, 8 Cyl 4.6L DOHC EFI, 8 Cyl 4.6L DOHC EFI S/C | 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R70W (AODE), 5MT, 5-Speed Manual Transmission (T450D), 5-Speed Manual Transmission T5OD, 5-Speed Manual Transmission TR3650, 6-Speed Manual Transmission Tremec T56, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: E8ZZ-6507-A
$41.06 MSRP: $59.00
You Save: $17.94 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1993 Ford Mustang | 4 Cyl 2.3L, 6 Cyl 3.3L, 6 Cyl 3.8L, 8 Cyl 4.2L, 8 Cyl 5.0L | 3AT C3, 3AT C4, 3AT C5, 4AT A4LD, 4AT AOD, 4MT, 5MT
View related parts
Ford Mustang Valve - Inlet
Part Number: F65Z-6507-AA
$9.73 MSRP: $13.87
You Save: $4.14 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Manufacturer Note: STD.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2004 Ford Mustang | 6 Cyl 3.8L, 6 Cyl 3.8L OHV EFI, 6 Cyl 3.9L OHV EFI NA | 4AT 4R70W, 4AT 4R75W, 4-Speed Automatic Transmission 4R70W (AODE), 5MT, 5-Speed Manual Transmission (T450D), 5-Speed Manual Transmission T5OD, 5-Speed Manual Transmission TR3650, 6-Speed Manual Transmission Tremec T56, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang VALVE - INLET
Part Number: GR3Z-6507-B
$26.68 MSRP: $38.00
You Save: $11.32 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Replaces: GR3Z-6507-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2022 Ford Mustang | 8 Cyl 5.2 L GAS, 8 Cyl 5.2L | 10-Speed Automatic Transmission (10R80), 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission-3160, 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve - Inlet
Part Number: CR3Z-6507-A
$31.68 MSRP: $44.00
You Save: $12.32 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Mustang | 8 Cyl 5.0L DOHC EFI Modular | 6-Speed Automatic Transmission (6R80), 6-Speed Manual Transmission (T56), 6-Speed Manual Transmission-MT82, Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Mustang Valve Inlet
Part Number: E7AZ6507A
Product Specifications
- Other Name: Valve - Inlet; Intake Valve, Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986 Ford Mustang | 4 Cyl 2.3L, 6 Cyl 3.8L, 8 Cyl 5.0L | 3AT C3, 3AT C5, 4AT AOD, 4MT, 5MT
View related parts
Ford Mustang Valve
Part Number: E83Z6507A
Product Specifications
- Other Name: Valve - Inlet; Valves
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1989 Ford Mustang | 4 Cyl 2.3L, 8 Cyl 5.0L | 4AT A4LD, 4AT AOD, 5MT
View related parts
Ford Mustang Valve Inlet
Part Number: E8ZZ6507C
Product Specifications
- Other Name: Valve - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1993 Ford Mustang | 4 Cyl 2.3L, 6 Cyl 3.3L, 6 Cyl 3.8L, 8 Cyl 4.2L, 8 Cyl 5.0L | 3AT C3, 3AT C4, 3AT C5, 4AT A4LD, 4AT AOD, 4MT, 5MT

| Page 1 of 2 |Next >

1-20 of 25 Results

Ford Mustang Intake Valve

The Intake Valve in the Ford Mustang automobiles is responsible for boosting the engine efficiency and also regulating combustion chamber. Basically, it serves the purpose of controlling the duration of admittance of air and fuel mixture into the engine so that power is maintained and efficiency achieved. This is because when the Intake Valve fails in its operation, it compromises the combustion process as well as the engine power hence the need to be replaced as soon as possible to avoid incurring costly repairs. It is worth noticing that there are different Intake Valves had been used on the Ford Mustang models over the years with each is intended for particular performance characteristics. In the process of replacing a damaged Intake Valve some special tools such as the compressors of valve springs and retainers are employed. This is a fundamental requirement to meet to guarantee the efficiency of the Intake Valve hence improving the Ford Mustang's performance.

We provide a wide range of Ford Mustang Intake Valve at the best prices possible. If you need Ford Mustang Intake Valve, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Mustang Intake Valve Parts Questions & Experts Answers

Valve - Inlet
2L2Z-6507-AA
Q: How to check and adjust valve clearances after replace camshafts or valve-related parts on Ford Mustang?
A: It is important to check the valve clearances with the help of a cold engine. It is recommended that the valve clearances be checked and altered only after the Camshaft(s) or any other related valve parts have been replaced, or when there is much rumbling noise in the valve-train. Start from disconnecting the cable that is connected to the negative terminal of the battery next is remove the spark plugs and the valve covers. Position the engine with the Crankshaft Pulley center bolt on the cylinder to be checked until cam lobes are out of the lifters as possible using socket and breaker bar. Gauge the clearance of each valve with a feeler gauge of the specified thickness; slight drag on the feeler gauge will tell that the clearance is correct. Record any valve which is out of specification as this will form part of the analysis when estimating the number of required replacement lifters. Again we shall repeat the same process for all the valves. Any of the clearance that exist must be adjusted by replacing the lifter with a new lifter whose thickness head is of a different measure. Stoke the lifters to be replaced and record their assorted valves. Head thickness of each lifter is to be measured using the micrometer on the center projection on the underside for accuracy. To calculate the correct thickness for a replacement lifter that will achieve the specified valve clearance, use the formula: A new lifter thickness would therefore be calculated as: N equal R + (M1-M2) These lifters are stamped on the bottom to show their size such a code 3.310 means the thickness is 3.31mm or 0.13 inch. This lifters are then marked according to their installation location, then applied with engine assembly lube and finally installed. To rectify the problem replace the lifters, reset the camshafts and Timing Chains and after that adjust the valve clearances.