×
- Live Chat
- 1-888-788-9341
My Garage
My Account
Cart
Genuine Ford Ranger Mass Air Flow Sensor
MAF Sensor Meter- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
12 Mass Air Flow Sensors found
Ford Ranger Mass Air Flow Sensor
One of the most important sensors found in Ford ranger cars is the Mass Air Flow Sensor or MAF which is used to measure the amount of air a car engine needs in order to provide the premier performance. This information is sent to the PCM that integrates it andctlches the fuel injector time so as to provide the correct blended air/fuel mixture for burning. Various Mass Air Flow Sensor have been used on Ford Rangers; for example, Vane Meters (VAF) and Hot Wire sensors. VAF sensor for example is an efficient but likely to cause limited air flow and also undergo mechanical tread while on the other hand Hot Wire sensor provides high level of accuracy and flexibility but is likely to be compromised by contaminants. In particular issues with the MAF sensor, such as a buildup of dirt, can cause either stalling or improper air-fuel mix or sensor malfunction.
We provide a wide range of Ford Ranger Mass Air Flow Sensor at the best prices possible. If you need Ford Ranger Mass Air Flow Sensor, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.
Ford Ranger Mass Air Flow Sensor Parts Questions & Experts Answers
- Q: How to replace the Brake Light Switch,Camshaft Position Sensor,Coolant Temperature Sensor,Crankshaft Position Sensor,Cylinder Head Temperature Sensor,Idle Control Valve,Intake Manifold Temperature Sensor,Mass Air Flow Sensor,Oxygen Sensors,Throttle Position Sensor and Vehicle Speed Sensor on 1993-2011 Ford Ranger?A: To replace Engine Coolant Temperature (ECT) sensor for 2011 models, drain the cooling system, wrap new sensor's threads with Teflon sealing tape, unplug the electrical connector and remove the sensor by thermostat housing. For 2001 and newer 2.3L models a Cylinder Head Temperature (CHT) sensor is used; disconnect battery, expose electrical connector, unscrew and remove CHT sensor. The Oxygen Sensor replacement involves disconnecting the battery, raising the vehicle and removing the O2 sensor using proper tool, apply anti-seize compound to new threads and tighten it into place. Throttle Position Sensor (TPS) replacement requires disconnecting of battery, removal of throttle body cover, unfastening of TPS and ensure proper alignment during installation. Replacing Mass Airflow Sensor (MAF) means; firstly you need to disconnect battery from its terminal, then undo electrical connection between MAF sensor's plug-in connectors followed by taking off MAF sensor itself lastly install new one with a fresh gasket on 2011 models. To control air conditioning clutch relay PCM controls this while checking fuses for any malfunctioning Air conditioning clutch control means that PCM operates this clutch relay as you verify fuses for defects which may be interfering with idle speed quality in your vehicle at all times Vehicle Speed Sensor (VSS) change applies to those vehicles made before 1997; therefore when replacing it you are supposed to detach an electric connector from a particular component installed in a car under consideration while removing retaining bolt also do not forget about reversing above mentioned process Intake Manifold Temperature Sensor replacement includes disconnecting the battery, unplugging the intake manifold temperature sensor connector, removing the IMTS from intake manifold Idle Air Control (IAC) valve replacement requires disconnection of battery power supply followed by taking IAC valve cover out where electronic wires should be disconnected only after unscrewing screws Power steering pressure switch inspection comprises of checking fuses as well as circuits that might be affecting idle quality in your automobile Camshaft Position (CMP) sensor replacement varies with model, which may include but not limited to separating the battery, loosening electrical connector, removing sensor then fitting the new one properly. Crankshaft Position (CKP) sensor replacement includes disconnecting battery, removal of things like accessory drive belt or alternator, unscrewing of the sensor and installing new one with specific alignment procedures for different models Brake Light Switch or Brake Pedal Position (BPP) Sensor information informs about its purpose that is to show whether brakes are applied or not and it is located on brake pedal assembly.
Related Ford Ranger Parts
Ford Ranger Oxygen Sensors
Ford Ranger Throttle Position Sensor
Ford Ranger Coolant Temperature Sensor
Ford Ranger Temperature Sender
Ford Ranger Vehicle Speed Sensor
Ford Ranger MAP Sensor
Ford Ranger Parking Assist Distance Sensor
Ford Ranger Knock Sensor
Ford Ranger Crankshaft Position Sensor
Ford Ranger Camshaft Position Sensor
Browse by Year
2011 Mass Air Flow Sensor 2010 Mass Air Flow Sensor 2009 Mass Air Flow Sensor 2008 Mass Air Flow Sensor 2007 Mass Air Flow Sensor 2006 Mass Air Flow Sensor 2005 Mass Air Flow Sensor 2004 Mass Air Flow Sensor 2003 Mass Air Flow Sensor 2002 Mass Air Flow Sensor 2001 Mass Air Flow Sensor 2000 Mass Air Flow Sensor 1999 Mass Air Flow Sensor 1998 Mass Air Flow Sensor 1997 Mass Air Flow Sensor 1994 Mass Air Flow Sensor 1993 Mass Air Flow Sensor 1992 Mass Air Flow Sensor 1991 Mass Air Flow Sensor 1990 Mass Air Flow Sensor