How to replace the Brake Light Switch,Camshaft Position Sensor,Coolant Temperature Sensor,Crankshaft Position Sensor,Cylinder Head Temperature Sensor,Idle Control Valve,Intake Manifold Temperature Sensor,Mass Air Flow Sensor,Oxygen Sensors,Throttle Position Sensor and Vehicle Speed Sensor on 1993-2011 Ford Ranger?

To replace Engine Coolant Temperature (ECT) sensor for 2011 models, drain the cooling system, wrap new sensor's threads with Teflon sealing tape, unplug the electrical connector and remove the sensor by thermostat housing. For 2001 and newer 2.3L models a Cylinder Head Temperature (CHT) sensor is used; disconnect battery, expose electrical connector, unscrew and remove CHT sensor. The Oxygen Sensor replacement involves disconnecting the battery, raising the vehicle and removing the O2 sensor using proper tool, apply anti-seize compound to new threads and tighten it into place. Throttle Position Sensor (TPS) replacement requires disconnecting of battery, removal of throttle body cover, unfastening of TPS and ensure proper alignment during installation. Replacing Mass Airflow Sensor (MAF) means; firstly you need to disconnect battery from its terminal, then undo electrical connection between MAF sensor's plug-in connectors followed by taking off MAF sensor itself lastly install new one with a fresh gasket on 2011 models. To control air conditioning clutch relay PCM controls this while checking fuses for any malfunctioning Air conditioning clutch control means that PCM operates this clutch relay as you verify fuses for defects which may be interfering with idle speed quality in your vehicle at all times Vehicle Speed Sensor (VSS) change applies to those vehicles made before 1997; therefore when replacing it you are supposed to detach an electric connector from a particular component installed in a car under consideration while removing retaining bolt also do not forget about reversing above mentioned process Intake Manifold Temperature Sensor replacement includes disconnecting the battery, unplugging the intake manifold temperature sensor connector, removing the IMTS from intake manifold Idle Air Control (IAC) valve replacement requires disconnection of battery power supply followed by taking IAC valve cover out where electronic wires should be disconnected only after unscrewing screws Power steering pressure switch inspection comprises of checking fuses as well as circuits that might be affecting idle quality in your automobile Camshaft Position (CMP) sensor replacement varies with model, which may include but not limited to separating the battery, loosening electrical connector, removing sensor then fitting the new one properly. Crankshaft Position (CKP) sensor replacement includes disconnecting battery, removal of things like accessory drive belt or alternator, unscrewing of the sensor and installing new one with specific alignment procedures for different models Brake Light Switch or Brake Pedal Position (BPP) Sensor information informs about its purpose that is to show whether brakes are applied or not and it is located on brake pedal assembly.

Genuine Ford Ranger Oxygen Sensors

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Oxygen Sensors found

View related parts
Ford Ranger Sensor - Hego
Part Number: XL3Z-9F472-AA
$67.32 MSRP: $111.27
You Save: $43.95 (40%)
ADD TO CART
Product Specifications
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2011 Ford Ranger | 4 Cyl 2.3L NA Petrol, 6 Cyl 3.0L, 6 Cyl 3.0L OHV EFI | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Sensor Assembly
Part Number: F85Z-9G444-BA
$61.27 MSRP: $83.72
You Save: $22.45 (27%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Sensor Assy
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2006 Ford Ranger | 6 Cyl 3.0L OHV EFI, 6 Cyl 4.0L SOHC EFI | 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Sensor - Exhaust Gas - Oxygen
Part Number: F85Z-9G444-F
$61.27 MSRP: $83.72
You Save: $22.45 (27%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Ford Ranger | 6 Cyl 3.0L OHV EFI, 6 Cyl 4.0L SOHC EFI | 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Sensor Assembly
Part Number: F8TZ-9G444-CA
$105.23 MSRP: $209.09
You Save: $103.86 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assy; Oxygen Sensor, Rear Oxygen Sensor
- Replaces: F7TZ-9G444-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-2001 Ford Ranger | 4 Cyl 2.5L, 6 Cyl 3.0L, 6 Cyl 4.0L | 4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R44E, 5AT 5R55E, 5MT
View related parts
Ford Ranger Sensor - Hego
Part Number: XL3Z-9F472-BA
$35.80 MSRP: $57.09
You Save: $21.29 (38%)
ADD TO CART
Product Specifications
- Other Name: Front Oxygen Sensor, Oxygen Sensor
- Position: Driver Side & Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2011 Ford Ranger | 4 Cyl 2.3L NA Petrol, 6 Cyl 3.0L OHV EFI, 6 Cyl 4.0L SOHC EFI | 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Sensor - Hego
Part Number: F85Z-9G444-AB
$49.72 MSRP: $82.18
You Save: $32.46 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Position: Passenger Side
- Replaced by: GU2Z-9G444-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2006 Ford Ranger | 4 Cyl 2.3L NA Petrol, 6 Cyl 3.0L, 6 Cyl 3.0L OHV EFI, 6 Cyl 4.0L SOHC EFI | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Sensor - Exhaust Gas - Oxygen
Part Number: F85Z-9G444-E
$49.72 MSRP: $82.18
You Save: $32.46 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Position: Driver Side
- Replaced by: GU2Z-9G444-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Ford Ranger | 4 Cyl 2.3L NA Petrol, 6 Cyl 3.0L OHV EFI, 6 Cyl 4.0L SOHC EFI | 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger SENSOR - EXHAUST GAS - OXYGEN
Part Number: KB3Z-9G444-C
$69.20 MSRP: $110.36
You Save: $41.16 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Oxygen Sensor, Oxygen Sensor
- Replaces: DY-1481, KB3Z-9G444-A, DY-1590, KB3Z-9G444-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 2 Whl L/H Rear Drive-High Ride, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Ranger SENSOR - HEGO
Part Number: KB3Z-9F472-A
$91.20 MSRP: $145.45
You Save: $54.25 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oxygen Sensor, Upper Oxygen Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 2 Whl L/H Rear Drive-High Ride, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Ranger SENSOR - EXHAUST GAS - OXYGEN
Part Number: KB3Z-9G444-A
$69.20 MSRP: $110.36
You Save: $41.16 (38%)
ADD TO CART
Product Specifications
- Other Name: Oxygen Sensor
- Replaced by: KB3Z-9G444-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019 Ford Ranger | 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 2 Whl L/H Rear Drive-High Ride, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Ranger Sensor Assembly
Part Number: E63Z9F472A
Product Specifications
- Other Name: Sensor Assy; Oxygen Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989 Ford Ranger | 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 5MT
- 1983-1985 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.3L | 3AT C3, 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Ranger Sensor - Hego
Part Number: XL3Z-9F472-C
$144.78 MSRP: $230.91
You Save: $86.13 (38%)
Product Specifications
- Other Name: Front Oxygen Sensor, Oxygen Sensor
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Ranger | 6 Cyl 3.0L OHV EFI | 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Sensor Assembly
Part Number: E6TZ-9F472-A
Product Specifications
- Other Name: Sensor Assy; Oxygen Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989 Ford Ranger | 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 5MT
- 1983-1985 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.3L | 3AT C3, 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Ranger Sensor Hego
Part Number: E6TZ9F472D
Product Specifications
- Other Name: Sensor - Hego; Oxygen Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989 Ford Ranger | 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 5MT
- 1983-1985 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.3L | 3AT C3, 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Ranger Sensor Assembly
Part Number: E6ZZ9F472A
Product Specifications
- Other Name: Sensor Assy; Oxygen Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989 Ford Ranger | 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 5MT
- 1983-1985 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.3L | 3AT C3, 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Ranger Sensor - Hego
Part Number: F6DZ-9G444-CA
Product Specifications
- Manufacturer Note: D/L=482mm
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997 Ford Ranger | 4 Cyl 2.3L | 4AT 4R44E, 5AT 5R55E, 5MT
View related parts
Ford Ranger Sensor Assembly
Part Number: F85Z-9G444-DA
Product Specifications
- Other Name: Sensor Assy; Oxygen Sensor
- Replaces: F75Z-9G444-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-2003 Ford Ranger | 6 Cyl 3.0L, 6 Cyl 4.0L | 4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R44E, 5AT 5R55E, 5MT

Ford Ranger Oxygen Sensors

The Oxygen Sensors in Ford Ranger vehicles helps in controlling the air/fuel mix by measuruing unburned oxygen from exhaust streams. This sensor produces an electrical voltage proportionate to the presence or absence of oxygen, enabling the engine control computer to add or subtract fuel in order to get the most kilometres out of the gas and at the same time minimize emissions. Most Ford Rangers have no less than two oxygen sensors, one upstream of the catalytic converter, and the other downstream of the converter; the upstream sensor supplies the feedback. These sensors are typically used at high temperatures and can deteriorate following contamination in terms of localized emissions to enhance fuel intake. Many earlier models might sit SA pressures, while some of the latest automotive models employ air/fuel ratio sensors that allow for a greater selection of options for correct results. It must be remembered that like any other component of a car, sensors also require proper upkeep and often, proper examination to guarantee their correct functioning as well as to maintain an efficient vehicle.

We provide a wide range of Ford Ranger Oxygen Sensors at the best prices possible. If you need Ford Ranger Oxygen Sensors, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Ranger Oxygen Sensors Parts Questions & Experts Answers

Sensor - Exhaust Gas - Oxygen
F85Z-9G444-F
Q: How to replace the Brake Light Switch,Camshaft Position Sensor,Coolant Temperature Sensor,Crankshaft Position Sensor,Cylinder Head Temperature Sensor,Idle Control Valve,Intake Manifold Temperature Sensor,Mass Air Flow Sensor,Oxygen Sensors,Throttle Position Sensor and Vehicle Speed Sensor on 1993-2011 Ford Ranger?
A: To replace Engine Coolant Temperature (ECT) sensor for 2011 models, drain the cooling system, wrap new sensor's threads with Teflon sealing tape, unplug the electrical connector and remove the sensor by thermostat housing. For 2001 and newer 2.3L models a Cylinder Head Temperature (CHT) sensor is used; disconnect battery, expose electrical connector, unscrew and remove CHT sensor. The Oxygen Sensor replacement involves disconnecting the battery, raising the vehicle and removing the O2 sensor using proper tool, apply anti-seize compound to new threads and tighten it into place. Throttle Position Sensor (TPS) replacement requires disconnecting of battery, removal of throttle body cover, unfastening of TPS and ensure proper alignment during installation. Replacing Mass Airflow Sensor (MAF) means; firstly you need to disconnect battery from its terminal, then undo electrical connection between MAF sensor's plug-in connectors followed by taking off MAF sensor itself lastly install new one with a fresh gasket on 2011 models. To control air conditioning clutch relay PCM controls this while checking fuses for any malfunctioning Air conditioning clutch control means that PCM operates this clutch relay as you verify fuses for defects which may be interfering with idle speed quality in your vehicle at all times Vehicle Speed Sensor (VSS) change applies to those vehicles made before 1997; therefore when replacing it you are supposed to detach an electric connector from a particular component installed in a car under consideration while removing retaining bolt also do not forget about reversing above mentioned process Intake Manifold Temperature Sensor replacement includes disconnecting the battery, unplugging the intake manifold temperature sensor connector, removing the IMTS from intake manifold Idle Air Control (IAC) valve replacement requires disconnection of battery power supply followed by taking IAC valve cover out where electronic wires should be disconnected only after unscrewing screws Power steering pressure switch inspection comprises of checking fuses as well as circuits that might be affecting idle quality in your automobile Camshaft Position (CMP) sensor replacement varies with model, which may include but not limited to separating the battery, loosening electrical connector, removing sensor then fitting the new one properly. Crankshaft Position (CKP) sensor replacement includes disconnecting battery, removal of things like accessory drive belt or alternator, unscrewing of the sensor and installing new one with specific alignment procedures for different models Brake Light Switch or Brake Pedal Position (BPP) Sensor information informs about its purpose that is to show whether brakes are applied or not and it is located on brake pedal assembly.