×
Contact Us Live Chat or 1-888-788-9341
My Garage
My Account
Cart
Search Bar
Search by Part Number, Part Name, or Vehicle
Track Order Help Center
Make sure this part fits

Ford F57Z-9424-D Manifold Assembly - Inlet

1995-2001 Ford Ranger F57Z9424D

Customer Questions & Expert Answers (12)
Ford F57Z-9424-D Manifold Assembly - Inlet
Ford F57Z-9424-D Manifold Assembly - Inlet
Ford F57Z-9424-D Manifold Assembly - Inlet
  • Part Description
    Manifold Assy - Inlet
  • Base No.
    9424
  • Position
    Lower
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers

  • Related Parts

    Shop for related parts for your vehicle

  • Product Specifications

    BrandGenuine Ford
    Base No.9424
    Manufacturer Part NumberF57Z-9424-D, F57Z9424D
    Part DescriptionManifold Assy - Inlet
    Other NamesIntake Manifold, Manifold
    Item Dimensions18.6 x 13.5 x 9.0 inches
    Item Weight7.60 Pounds
    PositionLower
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerFord
    SKUF57Z-9424-D
    WarrantyThis genuine Ford part is guaranteed by Ford's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65

  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1995-2001 Ford Ranger4 Cyl 2.3L, 4 Cyl 2.5L4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R44E, 5AT 5R55E, 5MT

  • Customer Questions & Expert Answers

    Q:
    Is the the correct part for the attached VIN? Posted by FordPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if F57Z-9424-D fits your vehicle.
    Posted by FordPartsGiant Specialist
    Q:
    How should the manifold be installed for the 2001 Ford Ranger? Posted by Customer
    A:
    Install the manifold over the studs. Install the nuts and bolts and tighten them finger tight.
    Posted by FordPartsGiant Specialist
    Q:
    What is the next step after handling the ignition wires for the 2008 Ford Ranger? Posted by Customer
    A:
    Remove the intake manifold mounting bolts.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done to the mating surfaces before installation for the 2008 Ford Ranger? Posted by Customer
    A:
    Thoroughly clean all old gasket material from the mating surfaces of the upper intake manifold and the lower intake manifold.
    Posted by FordPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What is the next step after securing the intake manifold for the 1999 Ford Ranger? Posted by Customer
    A:
    The remainder of installation is the reverse of removal.
    Posted by FordPartsGiant Specialist
    Q:
    What is the first step in the installation process for the 2004 Ford Ranger? Posted by Customer
    A:
    Clean the manifold and head mating surfaces and check the manifold for cracks.
    Posted by FordPartsGiant Specialist
    Q:
    How should the intake manifold be removed for the 2001 Ford Ranger? Posted by Customer
    A:
    Remove the intake manifold. It may be necessary to pry between the manifold and block, using the water pump lug as a fulcrum. Use care to avoid damaging the machined surfaces. Do not pry between the gasket surfaces or leaks will develop. The fuel rails and injectors may remain in place. Lift the manifold out of the engine compartment.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done with the heater hose during removal for the 2005 Ford Ranger? Posted by Customer
    A:
    Disconnect the heater hose from the front of the intake manifold. You may also need to remove the thermostat and housing or disconnect the upper radiator hose from the outlet fitting.
    Posted by FordPartsGiant Specialist
    Q:
    What needs to be installed after the gaskets for the 2009 Ford Ranger? Posted by Customer
    A:
    Install the front and rear manifold end seals, ensuring the locating pins are pressed into place.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done with the heater hose for the 2008 Ford Ranger? Posted by Customer
    A:
    Disconnect the heater hose from the coolant pipe.
    Posted by FordPartsGiant Specialist
    Q:
    What should be done after installing the wheel and lowering the 2002 Ford Ranger? Posted by Customer
    A:
    Remove the bolts securing the upper portion of the accessory drive bracket, then remove the bracket.
    Posted by FordPartsGiant Specialist
    Q:
    What should be removed after disconnecting the battery for the 2007 Ford Ranger? Posted by Customer
    A:
    Remove the intake air duct from the air filter housing.
    Posted by FordPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Ford Part F57Z-9424-D, the Right Choice

To ensure reliability, purchase Ford part # F57Z-9424-D Manifold Assembly - Inlet. It is sometimes referred to as Ford Intake Manifold. In terms of quality and longevity, OEM parts are top-tier. This is because they are made according to Ford's demanding factory specifications and go through strict quality control. This part fits specific Ford Ranger models.

FordPartsGiant.com is a leading supplier of genuine Ford parts and accessories such as Ford F57Z9424D Manifold Assembly - Inlet. On our platform, we provide genuine Ford parts at incredible prices while ensuring top-tier quality. Feel at ease shopping with us, knowing our parts have a hassle-free return policy and rapid delivery service. For detailed Ford parts information, click here.

Why choose Ford Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly