How to remove and install front Stabilizer bar and bushings on Ford Edge?

In order to remove the sway bar kit and do other related tasks, first make sure that the steering wheel is securely positioned at center using a steering wheel holding tool or passing the seat belt through the steering wheel and clipping it in place. Loosen front wheel lug nuts, lift up front part of vehicle, and support with jack stands; apply parking brake and block rear wheels for safety measures. At this moment take off your front wheels, mark where your steering shaft meets the steering gear and by taking away clamp bolt disconnect your steering shaft from your steerage gear. Afterwards remove right-hand side fender splash guards as well as sub frame lower bumper covers after removing those nuts. In case of 2014s models or older ones, detach power steering hose bracket and also remove forward section of exhaust system. If you are working on an all-wheel drive model, make an index mark on driveshaft, disconnect it from transfer case then reposition it. Disconnect sway bar links, tie rod ends and ball joints from their respective components securing harnesses and electrical connectors when necessary. Remove engine roll restrictor heat shield and bolt with making a mark down position of front sub-frame under body at the mounting locations namely; supporting front sub-frame with floor jacks unbolting bolts/nuts from sub-frame support brackets alright lifting sub-frame with jacks about 3 inches lower than that. Lose clamps for sway bar bushing's guide into freedom while sliding out sway bar kit. When removed from vehicle slide off retainer bushings checking them for cracks or wear replacing if necessary. Wipe off rust or dirt in area where sway bar bushing fits with wire brush for cleaning purposes before installation process starts; in relation to installation tighten fasteners according to specified torque values thus ensuring installation of bushings without lubricants especially noting correct positioning of them for 2015 & later models. Finally align sub-frame with marks made on installation place: tighten sub-frame nuts and then secure remaining support bracket fasteners.

How to remove and install rear Stabilizer bar and bushings on Ford Edge?

Find a hoist or place the car on ramps and safely block it to prevent any accidents or raise the rear of the vehicle as well as secure it with jack stands. The vehicle will not roll off the stands if you block its front wheels. Take off nuts from lower and upper ends of left and right sway bar links, hence removing them. Unscrew nuts that hold sway bar bushing brackets and take away brackets together with sway bar kit. Once you have removed the sway bar kit, check for cracks, wear or deterioration of bushings; replace if necessary. Remove rusts and dirt from around the bushing area of the sway bar kit by brushing it using wire brush. To make it easy when putting back new bushings on new Kit use vegetable oil (used in cooking) to lubricate their exterior/interior surfaces. No petroleum based lubricants, mineral oils, or brake fluids should be used because they will damage the bushings. Installation is basically doing what was done during removal but this time tightening fasteners to torque values.

Genuine Ford Edge Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Sway Bar Kits found

View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: 7T4Z-5A772-BA
$49.80 MSRP: $69.18
You Save: $19.38 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Stabilizer
Part Number: F2GZ-5482-B
$140.22 MSRP: $205.00
You Save: $64.78 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | 6 Cyl 2.7 L GAS, 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: F2GZ-5A772-A
$107.06 MSRP: $195.00
You Save: $87.94 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2021 Ford Edge | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: 7T4Z-5A772-A
$27.51 MSRP: $37.59
You Save: $10.08 (27%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: F2GZ-5A772-B
$112.55 MSRP: $205.00
You Save: $92.45 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L EcoBoost (240PS), 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Stabilizer
Part Number: BT4Z-5482-A
$150.70 MSRP: $228.33
You Save: $77.63 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: F2GZ-5A772-C
$141.36 MSRP: $206.67
You Save: $65.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | 6 Cyl 2.7 L GAS, 6 Cyl 2.7L, 6 Cyl 3.5L Cyclone Petrol TIVCT | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: DT4Z-5A772-A
$115.14 MSRP: $168.33
You Save: $53.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Stabilizer
Part Number: F2GZ-5482-A
$147.06 MSRP: $215.00
You Save: $67.94 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Bar - Stabilizer
Part Number: G2GZ-5482-A
$132.24 MSRP: $193.33
You Save: $61.09 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2019 Ford Edge | 4 Cyl 2.0L DOHC, 4 Cyl 2.0L Duratorq-TDCi (132kW/180PS) | 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, 6-Speed Manual Transaxle - MMT6, 8-Speed Automatic Transmission 8F57, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Edge Bar - Stabilizer
Part Number: 7T4Z-5482-B
Product Specifications
- Other Name: Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: 7A1Z-5A772-AA
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2010 Ford Edge | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Stabilizer
Part Number: 7T4Z-5482-A
Product Specifications
- Other Name: Stabilizer Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: BT4Z-5A772-A
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Edge Bar - Rear Stabilizer
Part Number: BT4Z-5A772-B
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford Edge | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, Four-Wheel Drive (Full Time) (Left Hand Drive), Left Hand Drive

Ford Edge Sway Bar Kit

The Sway Bar Kit for Ford Edge cars offers improved vehicle stability due to the linkages of the opposite ends of the suspensions. This kit decreases body movement on cornering and over bumps on the road hence increasing stability. The function of the anti-roll bar is to counteract torque and enable wheels to be leveled to the same plane reducing lateral incline and increasing traction. Throughout the model years, Sway Bar Kits that have been used in the Ford Edge are the adjustable and the active anti-roll bars. Some of these advanced systems, may provide adjustable stiffness to enhance maneuverability and comfort. Newer kinds offer better roll stiffness than the conventional ones but do not affect the vertical spring rates and can involve sensors and hydraulics for control of the sway bars in Ford Edge vehicles and thereby, provides better control of the vehicle during driving.

We provide a wide range of Ford Edge Sway Bar Kit at the best prices possible. If you need Ford Edge Sway Bar Kit, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Edge Sway Bar Kit Parts Questions & Experts Answers

Bar - Stabilizer
F2GZ-5482-B
Q: How to remove and install front Stabilizer bar and bushings on Ford Edge?
A: In order to remove the sway bar kit and do other related tasks, first make sure that the Steering Wheel is securely positioned at center using a steering wheel holding tool or passing the seat belt through the steering wheel and clipping it in place. Loosen front wheel lug nuts, lift up front part of vehicle, and support with jack stands; apply parking brake and block rear wheels for safety measures. At this moment take off your front wheels, mark where your steering shaft meets the steering gear and by taking away clamp bolt disconnect your steering shaft from your steerage gear. Afterwards remove right-hand side fender splash guards as well as sub frame lower bumper covers after removing those nuts. In case of 2014s models or older ones, detach power steering hose bracket and also remove forward section of exhaust system. If you are working on an all-wheel drive model, make an index mark on driveshaft, disconnect it from transfer case then reposition it. Disconnect sway bar links, Tie Rod Ends and ball joints from their respective components securing harnesses and electrical connectors when necessary. Remove engine roll restrictor heat shield and bolt with making a mark down position of front sub-frame under body at the mounting locations namely; supporting front sub-frame with floor jacks unbolting bolts/nuts from sub-frame support brackets alright lifting sub-frame with jacks about 3 inches lower than that. Lose clamps for sway bar bushing's guide into freedom while sliding out sway bar kit. When removed from vehicle slide off retainer bushings checking them for cracks or wear replacing if necessary. Wipe off rust or dirt in area where sway bar bushing fits with wire brush for cleaning purposes before installation process starts; in relation to installation tighten fasteners according to specified torque values thus ensuring installation of bushings without lubricants especially noting correct positioning of them for 2015 & later models. Finally align sub-frame with marks made on installation place: tighten sub-frame nuts and then secure remaining support bracket fasteners.
Bar - Stabilizer
F2GZ-5482-B
Q: How to remove and install rear Stabilizer bar and bushings on Ford Edge?
A: Find a hoist or place the car on ramps and safely block it to prevent any accidents or raise the rear of the vehicle as well as secure it with jack stands. The vehicle will not roll off the stands if you block its front wheels. Take off nuts from lower and upper ends of left and right sway bar links, hence removing them. Unscrew nuts that hold sway bar bushing brackets and take away brackets together with sway bar kit. Once you have removed the sway bar kit, check for cracks, wear or deterioration of bushings; replace if necessary. Remove rusts and dirt from around the bushing area of the sway bar kit by brushing it using wire brush. To make it easy when putting back new bushings on new Kit use vegetable oil (used in cooking) to lubricate their exterior/interior surfaces. No petroleum based lubricants, mineral oils, or brake fluids should be used because they will damage the bushings. Installation is basically doing what was done during removal but this time tightening fasteners to torque values.

Related Ford Edge Parts

Browse by Year

2024 Sway Bar Kit 2023 Sway Bar Kit 2022 Sway Bar Kit 2021 Sway Bar Kit 2020 Sway Bar Kit 2019 Sway Bar Kit 2018 Sway Bar Kit 2017 Sway Bar Kit 2016 Sway Bar Kit 2015 Sway Bar Kit 2014 Sway Bar Kit 2013 Sway Bar Kit 2012 Sway Bar Kit 2011 Sway Bar Kit 2010 Sway Bar Kit 2009 Sway Bar Kit 2008 Sway Bar Kit 2007 Sway Bar Kit