What are the precautions and how to replace fuel filters in Ford F-250?

Fuel filters in carbureted models must be replaced according to the maintenance interval suggestions and when a blockage in the fuel line occurs due to excessive foreign material in the fuel. Given the volatile nature of gasoline, precautions should be exercised when the fuel filter is replaced. This work should be done on a cool engine, away from open flames and not within an enclosed area. Any spills should be cleaned up immediately. Fuel filters are located in different places depending on the year, engine size and weight rating of the vehicle. Most can be found in-line somewhere between the fuel pump and the carburetor. If a fuel filter is located in-line between the carburetor and the fuel pump, it is usually connected with rubber hoses. After removing the filter, drain it and discard it in a non-incendiary refuse container. Replace the filter with an exact duplicate replacement and push it into new rubber connecting hoses. Tighten all clamps, start the vehicle and check for leaks. If the filter is the type located in the inlet of the carburetor, first detach the line leading to the inlet. Carefully unscrew the carburetor inlet filter unit from the carburetor. To reinstall, simply thread a new filter into the carburetor and tighten securely. If an internal filter is located inside the carburetor inlet, the spring, gasket and filter must be removed. Assemble the new filter, seal and spring in the reverse order of their removal. Some fuel filters are located in the bottom of the fuel pump. To remove this type of filter, unscrew the canister from the bottom of the fuel pump. Slowly lower the canister and filter assembly off the bottom of the fuel pump. Empty the fuel into an approved gasoline container, then remove the filter and gasket assembly. Insert a new filter and gasket assembly. Screw the filter and filter housing assembly back on to the base of the fuel pump. Start the vehicle and check the filter and surrounding area for leaks.

How to remove and install a fuel filter in a Ford F-250?

Relieve the fuel system pressure and loosen the fuel filler cap. Disconnect the cable from the negative terminal of the battery. If necessary, raise the vehicle and support it securely on jack stands with the front end slightly higher than the rear. Locate the fuel filter on the inside of the left-side frame rail. Remove the filter-to-fuel line retainer clips if equipped. Remove the fuel lines from the filter. Remove the nuts retaining the filter bracket to the frame rail and remove the filter. Installation is the reverse of removal. Turn the key on and off several times to pressurize the system. Check the filter for leaks. Don't forget to reset the inertia switch.

Genuine Ford F-250 Fuel Filter

Gas Filter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Fuel Filters found

View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: F89Z-9155-A
$18.07 MSRP: $31.82
You Save: $13.75 (44%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Filter Assy - Fuel
- Replaced by: 2M5Z-9155-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.4L | 4AT 4R100, 4AT 4R70W, 5MT
View related parts
Ford F-250 Filter Assembly
Part Number: E5TZ-9J306-BA
$53.14 MSRP: $60.00
You Save: $6.86 (12%)
ADD TO CART
Product Specifications
- Other Name: Filter Assy; Fuel Filter, Fuel Strainer
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1997 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: FOTZ-9155-B
$20.24 MSRP: $35.64
You Save: $15.40 (44%)
ADD TO CART
Product Specifications
- Other Name: Fuel Filter
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1998 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R100, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Element
Part Number: F2TZ-9N184-A
$43.32 MSRP: $69.09
You Save: $25.77 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Fuel Filter, Fuel/Water Separator
- Replaces: E8TZ-9N184-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1994 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 7.3L | 3AT C6, 3MT, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Element
Part Number: E8TZ-9N184-A
$43.32 MSRP: $69.09
You Save: $25.77 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Fuel/Water Separator; Fuel Filter
- Replaced by: F2TZ-9N184-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1992 Ford F-250 | 8 Cyl 7.3L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Element
Part Number: F4TZ-9N184-A
$54.45 MSRP: $90.00
You Save: $35.55 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Fuel Filter, Fuel/Water Separator
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1996 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 7.3L | 3AT C6, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: E7DZ-9155-A
$21.09 MSRP: $33.64
You Save: $12.55 (38%)
ADD TO CART
Product Specifications
- Other Name: Filter Assy - Fuel
- Replaced by: YF1Z-9155-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1991 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 3MT, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: F4TZ-9155-B
$495.95 MSRP: $827.27
You Save: $331.32 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: FILTER ASY - FUEL
- Replaced by: F4TZ-9155-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Element
Part Number: F8CZ-9N184-AAGF
$38.29 MSRP: $53.19
You Save: $14.90 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-1999 Ford F-250 | 8 Cyl 5.4L | 4AT 4R100, 4AT 4R70W, 5MT
- 1996 Ford F-250 | 8 Cyl 7.3L | 3AT C6, 4AT E4OD, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: F6TZ-9155-A
$302.20 MSRP: $605.45
You Save: $303.25 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: FILTER ASY - FUEL
- Manufacturer Note: Fuel/Water/Filter Separator asy. Service all details in assembly except Filter F4TZ 9N184-A., 7.3L, except Calif. Ems.
- Replaced by: F6TZ-9155-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R70W, 4AT E4OD, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: D9PZ-9155-A
$13.73
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Filter Assy - Fuel; Fuel Filter
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1986 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.6L, 8 Cyl 6.9L, 8 Cyl 7.5L | 3AT C6, 3MT, 4AT AOD, 4MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: E3FZ-9155-F
$11.97 MSRP: $19.09
You Save: $7.12 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Filter Assy - Fuel; Fuel Filter
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1982-1986 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.6L, 8 Cyl 6.9L, 8 Cyl 7.5L | 3AT C6, 3MT, 4AT AOD, 4MT
View related parts
Ford F-250 Element
Part Number: F5TZ-9365-AA
$38.65 MSRP: $61.64
You Save: $22.99 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Manufacturer Note: Element for F6AZ-9155-AC housing/element located on frame rail next to 9C968, NGV
- Replaced by: 4W7Z-9365-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1998 Ford F-250 | 8 Cyl 5.4L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: E3TZ-9155-A
$47.08 MSRP: $75.09
You Save: $28.01 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Filter Assy - Fuel; Fuel Filter
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1983-1987 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L, 8 Cyl 7.5L | 3AT C6, 3MT, 4AT AOD, 4MT, 5MT
View related parts
Ford F-250 Element
Part Number: F6AZ-9155-AC
$38.65 MSRP: $61.64
You Save: $22.99 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Replaced by: 4W7Z-9365-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: D3AZ-9155-C
$8.47 MSRP: $13.51
You Save: $5.04 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Filter Assy - Fuel; Fuel Filter
- Replaces: FG-14-D, D3AZ-9155-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1981 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.6L | 3AT C6, 3MT, 4AT AOD, 4MT
View related parts
Ford F-250 Filter Assembly
Part Number: E1FZ9A011A
$18.83 MSRP: $26.16
You Save: $7.33 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Filter Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1997 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Filter Assembly
Part Number: D1AZ-9A011-A
Product Specifications
- Other Name: Filter Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1997 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Filter Assembly
Part Number: D1FZ-9A011-A
Product Specifications
- Other Name: Filter Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1997 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Filter Assembly - Fuel
Part Number: D3FZ-9155-B
Product Specifications
- Other Name: Filter Assy - Fuel
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1980-1981 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.6L | 3AT C6, 3MT, 4AT AOD, 4MT

| Page 1 of 2 |Next >

1-20 of 25 Results

About Ford F-250 Fuel Filter

Of all the high-precision auto parts within a car, the most important one is the Ford F-250 Fuel Filter. Keeping your F-250 Fuel Filter in top condition is critical to keeping your vehicle running smoothly. By buying a new replacement part, you can save hundreds, even thousands of dollars in costly auto repairs later down the road.

Ford F-250 Fuel Filter Parts Questions & Experts Answers

Element
E8TZ-9N184-A
Q: What are the precautions and how to replace fuel filters in Ford F-250?
A: Fuel filters in carbureted models must be replaced according to the maintenance interval suggestions and when a blockage in the fuel line occurs due to excessive foreign material in the fuel. Given the volatile nature of gasoline, precautions should be exercised when the fuel filter is replaced. This work should be done on a cool engine, away from open flames and not within an enclosed area. Any spills should be cleaned up immediately. Fuel filters are located in different places depending on the year, engine size and weight rating of the vehicle. Most can be found in-line somewhere between the fuel pump and the carburetor. If a fuel filter is located in-line between the carburetor and the fuel pump, it is usually connected with rubber hoses. After removing the filter, drain it and discard it in a non-incendiary refuse container. Replace the filter with an exact duplicate replacement and push it into new rubber connecting hoses. Tighten all clamps, start the vehicle and check for leaks. If the filter is the type located in the inlet of the carburetor, first detach the line leading to the inlet. Carefully unscrew the carburetor inlet filter unit from the carburetor. To reinstall, simply thread a new filter into the carburetor and tighten securely. If an internal filter is located inside the carburetor inlet, the spring, gasket and filter must be removed. Assemble the new filter, seal and spring in the reverse order of their removal. Some fuel filters are located in the bottom of the fuel pump. To remove this type of filter, unscrew the canister from the bottom of the fuel pump. Slowly lower the canister and filter assembly off the bottom of the fuel pump. Empty the fuel into an approved gasoline container, then remove the filter and gasket assembly. Insert a new filter and gasket assembly. Screw the filter and filter housing assembly back on to the base of the fuel pump. Start the vehicle and check the filter and surrounding area for leaks.
Element
F2TZ-9N184-A
Q: How to remove and install a fuel filter in a Ford F-250?
A: Relieve the fuel system pressure and loosen the fuel filler cap. Disconnect the cable from the negative terminal of the battery. If necessary, raise the vehicle and support it securely on jack stands with the front end slightly higher than the rear. Locate the fuel filter on the inside of the left-side frame rail. Remove the filter-to-fuel line retainer clips if equipped. Remove the fuel lines from the filter. Remove the nuts retaining the filter bracket to the frame rail and remove the filter. Installation is the reverse of removal. Turn the key on and off several times to pressurize the system. Check the filter for leaks. Don't forget to reset the inertia switch.